User's Manual

2.8 Label and compliance information
The final end product must be labeled in a visible area with the following: “Contains FCC ID:
RYK-WPEA251ACNIBT
. The grantee's FCC ID can be used only when all FCC compliance
requirements are met.
2.9
Information on test modes and additional testing requirements
This transmitter is tested in a standalone mobile RF exposure condition and any co
simultaneous transmission with other transmitter(s) or portable use will require a separate class
II permissive change re-
evaluation or new certification.
2.10 Additional testing, Part 15 Subpart B disclaimer
This transmitter module is tested as a subsystem and its certification does not cover the FCC Part
15 Subpart B (unintentional radiator) rule req
will still need to be reassessed for compliance to this portion of ru
As long as all conditions above are met, further
OEM integrator is still responsible for testing their end
requirements required with this module installed.
IMPORTANT NOTE:
In the event that these conditions
configurations or co-
location with another transmitter), then the FCC authorization is no longer
considered valid and the FCC ID
OEM integrator will be responsible for re
obtaining a separate FCC authorization.
Manual Information To the End User
The OEM integrator
has to be aware not to provide information to the end user regarding how to
install or remove this RF module in the user’s manual of th
module.
The end user manual shall include all required regulatory information/warning as show in this
manual.
OEM/Host manufacturer responsibilities
OEM/Host manufacturers are ultimately responsible for the compliance o
The final product must be reassessed against all the essential requirements of the FCC rule such as
FCC Part 15 Subpart B before it can be placed on the US market. This includes reassessing the
transmitter module for compliance with
This module must not be incorporated into any other device or system without retesting for
compliance as multi-
radio and combined equipment
Wireless Module
2.8 Label and compliance information
The final end product must be labeled in a visible area with the following: “Contains FCC ID:
. The grantee's FCC ID can be used only when all FCC compliance
Information on test modes and additional testing requirements
This transmitter is tested in a standalone mobile RF exposure condition and any co
simultaneous transmission with other transmitter(s) or portable use will require a separate class
evaluation or new certification.
2.10 Additional testing, Part 15 Subpart B disclaimer
This transmitter module is tested as a subsystem and its certification does not cover the FCC Part
15 Subpart B (unintentional radiator) rule req
uirement applicable to the final host. The final host
will still need to be reassessed for compliance to this portion of ru
le requirements if applicable
As long as all conditions above are met, further
transmitter
test will not be required. However, the
OEM integrator is still responsible for testing their end
-
product for any additional compliance
requirements required with this module installed.
In the event that these conditions
can not be met
(for example certain laptop
location with another transmitter), then the FCC authorization is no longer
considered valid and the FCC ID
can not
be used on the final product. In these circumstances, the
OEM integrator will be responsible for re
-
evaluating the end product (inclu
obtaining a separate FCC authorization.
Manual Information To the End User
has to be aware not to provide information to the end user regarding how to
install or remove this RF module in the user’s manual of th
e end product which integrates this
The end user manual shall include all required regulatory information/warning as show in this
OEM/Host manufacturer responsibilities
OEM/Host manufacturers are ultimately responsible for the compliance o
f the Host and Module.
The final product must be reassessed against all the essential requirements of the FCC rule such as
FCC Part 15 Subpart B before it can be placed on the US market. This includes reassessing the
transmitter module for compliance with
the Radio and EMF essential requirements of the FCC rules.
This module must not be incorporated into any other device or system without retesting for
radio and combined equipment
Wireless Module
The final end product must be labeled in a visible area with the following: “Contains FCC ID:
. The grantee's FCC ID can be used only when all FCC compliance
This transmitter is tested in a standalone mobile RF exposure condition and any co
-located or
simultaneous transmission with other transmitter(s) or portable use will require a separate class
This transmitter module is tested as a subsystem and its certification does not cover the FCC Part
uirement applicable to the final host. The final host
le requirements if applicable
.
test will not be required. However, the
product for any additional compliance
(for example certain laptop
location with another transmitter), then the FCC authorization is no longer
be used on the final product. In these circumstances, the
evaluating the end product (inclu
ding the transmitter) and
has to be aware not to provide information to the end user regarding how to
e end product which integrates this
The end user manual shall include all required regulatory information/warning as show in this
f the Host and Module.
The final product must be reassessed against all the essential requirements of the FCC rule such as
FCC Part 15 Subpart B before it can be placed on the US market. This includes reassessing the
the Radio and EMF essential requirements of the FCC rules.
This module must not be incorporated into any other device or system without retesting for