Instructions

Copyright © 2019 ANEST IWATA SPARMAX Co., Ltd.
1/2
PRODUCT SET UP
1. First use: Carefully unpack the unit, verify that all parts listed in the
“Parts List” are present, and visually inspect for damage. If there are
any signs of damage or if any parts are missing, do not use the
product. Contact your retailer or supplier immediately.
2. Place the compressor in a clean, dry, and well-ventilated area that
has adequate air circulation.
3. Connect ower shape adaptor of the PU Hose onto the compressor’s
Air Outlet , and the other end of the hose to your airbrush. NOTE:
Dierent adaptors may be required for dierent airbrush brands and
models. If your airbrush needs an adaptor, please contact your local
retailer or supplier.
4. Plug the appropriate end of the DC Power Supply into the
compressor.
PRODUCT OPERATION
1. Insert the wall plug of the DC Power Supply into a working power
outlet. Turn the compressor on by pressing the On/O Button. The
Button will light up with the power on.
2. To adjust air pressure, turn the pressure adjustment knob clockwise
to increase air pressure, or counter-clockwise to decrease air
pressure.
3. When the airbrush is not in use, place it into the Airbrush Holder, the
compressor will stop due to the Smart-Stop design. The compressor
will start working again at previous adjusted pressure when the
airbrush is taken o the holder. NOTE: Depending on the airbrush
model placed into the Airbrush Holder, the Smart Stop sensor
may not activate. In such case, position the compressor set until
the hose hangs down smoothly o the table and the Smart Stop is
able to detect the airbrush and activate.
4. To avoid damage, do not expose the Smart-Stop airbrush holder to
water or any forms of liquid.
5. Avoid touching any exposed metal parts on the compressor during,
or immediately after, operation. The compressor may be warm to
the touch for several minutes after operation.
6. It is recommended that the compressor run continuously for no
more than 30 minutes. After 30 minutes of continuous operation,
use the On/O Button to turn o the unit or place the airbrush into
the holder to pause the compressor. Allow the unit to cool for 10 to
15 minutes before turning the compressor back on.
7. After each use, make sure the unit is turned o and unplugged. Also
be sure to release any remaining air from the compressor by
depressing the airbrush trigger.
SMART STOP PATENTED TECHNOLOGY
The DC-25XR uses the Sparmax Smart-Stop design, which
automatically stops the compressor when a SPARMAX airbrush is
placed into the holder on the compressor. This energy saving design
allows users to stop the compressor when not in use. This reduces
pressure uctuations when compared to using an auto on/o switch
and regulator. The Smart-Stop is an intuitive design which aims to
improve user experience whilst extending the lifetime of the
compressor.
PATENTED WORLDWIDE
TW: M505546
GB: GB2532098
JP: 2014-006061
AU: 2015100687
CN: 201420781435.X
US: US20160131129A1
DE: Nr.202014106203.3
TROUBLESHOOTING
If airow is not sucient …
• Check for air leaks where air can be heard escaping, or apply a soap
and water solution on all connections. Resulting bubbles indicate an
air leak. Tighten ttings where necessary.
• PTFE seal tape is recommended for all threaded connections.
• Replace the Air Hose if the hose is torn or damaged.
If compressor shuts o frequently, the motor fails to come up to full
speed or becomes hotter than usual during operation …
• Disconnect other appliances that are using the same power outlet.
• Avoid using extension cords.
If problems arise which you cannot solve with the information
provided above, please contact your retailer or supplier for assistance.
Do not attempt to x the device yourself. Improper operation and/or
dismantling of the device may damage the compressor. If any
parts/accessories are damaged, please contact your retailer or supplier
for replacement or repair.
DC-25XR
User’s Manual
Auto ON
Auto OFF