MULTISCALE 1080p Scaler Box Operation Manual
TABLE OF CONTENTS 1. Introduction.............................................................................. 1 2. Features...................................................................................... 1 3.PackageContents..................................................................…..1 4. Operation Controls and Functions .......................................2 4.1 Front Panel...............................................................………....2 4.2 Rear Panel................................
1. Introduction SPATZ's Multiscale Scaler Box is designed to upscale digital/analog video signal from Composite, S-Video, PC, Component (HD) and HDMI input sources, to digital HDMI output of wide-range HDTV and PC resolutions, up to 1080p and WUXGA (1920 x 1200.) Besides video upscaling, the scaler box also converts digital/analog audio signal to digital format, then output either through HDMI combining with the video, or Coaxial S/PDIF separately.
. Operation Controls and Functions 4.1 Front Panel 1. POWER Button and LED Indicator: Press the button to turn ON/OFF the power of the unit. The LED will illuminate when the power is turned on. 2. IR remote control sensor. 3. Input Selection Buttons and LED Indicators: Press each of the buttons (CV/SV/COMP/PC/HDMI) to select the desired input source. The LED will illuminate when the corresponding input is selected. 4. MENU Button: Press the MENU button to bring up OSD operation menu (see section “4.
4.2. Rear Panel 1. HDMI OUT and CO-AX OUT: Connect the HDMI OUT port to the HDMI input port of your display such as HDTV. Connect the CO-AX OUT port to the Coaxial (S/PDIF) input port of your amplifier for separate digital audio output. 2. AUX IN Input: When the video signal input through the HDMI IN port is from a DVI source such as a PC, use the AUX IN port to input the audio signal. 3.
4.3.
4.4. Remote Control 1. POWER: Press the button once to power on the Multiscale Press again to enter standby mode. 2. INPUT: Press the button repeatedly to toggle through various input sources. 3. HD Input: Press the button to directly select component input. 4. PC Input: Press the button to directly select PC input. 5. HDMI/DVI Input: Press the button to directly select DVI (or HDMI) input. 6. Output Resolution: Press any one of the button to directly select output resolution.
Pin definition for serial cable PIN Multiscale Definition 1 NC 2 TxD 3 RxD 4 NC 5 GND 6 NC 7 NC 8 NC 9 NC RS-232 transmission format: BaudRate: 19200 bps Data Bit: 8 bits Parity: None Stop Bit: 1 bit PI 1 2 3 4 5 6 7 8 9 Remote Controller Definition NC Rx Tx NC GND NC NC NC NC
Serial Commands: Command Code Response Description S POWER 0 > POWER OFF POWER OFF S POWER 1 > POWER ON POWER ON S SOURCE 0 > SOURCE CV CV INPUT S SOURCE 1 > SOURCE SV SV INPUT S SOURCE 2 > SOURCE COMP COMP INPUT S SOURCE 3 > SOURCE PC PC INPUT S SOURCE 4 > SOURCE HDMI S OUTPUT 0 > OUTPUT NATIVE HDMI INPUT NATIVE RESOLUTION OUTPUT S OUTPUT 1 > OUTPUT VGA VGA RESOLUTION OUTPUT S OUTPUT 2 > OUTPUT SVGA SVGA RESOLUTION OUTPUT S OUTPUT 3 > OUTPUT XGA XGA RESOLUTION OUTPUT S OU
S BRIGHTNESS 0~100 S HUE 0~100 S SATURATION 0~100 S SHARPNESS 0~100 S NR 0~3 S PCHPOSITION 0~100 S PCVPOSITION 0~100 S PCCLOCK 0~100 S PCPHASE 0~63 S COLORTEMP 0~3 S RED 0~100 > BRIGHTNESS 0~100 > HUE 0~100 > SATURATION 0~100 SATURATION 0~100 ADJUST [Defaut:60] > SHARPNESS 0~100 SHARPNESS 0~100 ADJUST [Defaut:32] > NR OFF~HIGH 0:OFF; 1:LOW; 2:MIDDLE; 3:HIGH, NR CONTROL > PCHPOSITION H POSITION 0~100 ADJUST 0~100 > PCVPOSITION V POSITION 0~100 ADJUST 0~100 > PCCLOCK 0~100 PC MODE COLCK 0~100 ADJUST > PCPHA
(B) Status Commands: (Retrieve Status) Command Code R POWER R SOURCE R OUTPUT R SIZE R PICTUREMODE Response > POWER ON > SOURCE CV~HDMI > OUTPUT NATIVE~WUXGA > SIZE FULL~PANSCAN > PICTUREMODE STANDARD~USER Description SHOW POWER STATUS SHOW SOURCE STATUS SHOW OUTPUT STATUS SHOW SIZE STATUS SHOW PICTURE MODE STATUS R CONTRAST > CONTRAST 0~100 SHOW CONTRAST STATUS R BRIGHTNESS > BRIGHTNESS 0~100 SHOW BRIGHTNESS STATUS R HUE > HUE 0~100 SHOW HUE STATUS R SATURATION > SATURATION 0~100 SHOW SATURAT
5.2.