User manual

LNB - Fernspeisung
FürdieLNB-Fernspeisungsind3Betriebsartenwählbar:
12V: Alle 12 ZF-Eingänge (1…12) führen 12 Volt Fernspeisung (Betriebsart für
Quattro - LNB)
18V: DievertikalenZF-Eingängeführen14VoltunddiehorizontalenZF-Eingänge
führen 18 Volt
22kHz: WieSchalterstellung18Volt,jedochsinddieHigh-BandEingängemit22kHz
moduliert (Betriebsart QUAD - LNB)
Die Schalterstellung hat keinen Einfluss auf die Steuersignale des Receivers!
Die zutreffende LNB-Fernspeisespannung kann für die Betriebsfunktion „Standby“
oder „Dauerbetrieb“ eingestellt werden.
FürdieLNB-FernspeisespannungstehteinFernspeisestromvoninsgesamt1200mA
zur Verfügung (maximal 400 mA pro LNB)
Selektive Standby - Funktion
• DasPower-BasisgerätverfügtübereineselektiveStandby-Funktion.
Beispiel: Schauen alle Teilnehmer TV - Programme ausschließlich vom SAT - System A,
wird nur das dafür eingesetzte LNB versorgt. Die interne Logik schaltet die
Versorgungsspannung sowohl zu den übrigen LNBs als auch für die integrierten
Verstärker ab. Dieser Vorgang bewirkt eine deutliche Energieeinsparung!
Signalisierung der Standby - Funktion
• DieterrestrischeVerteilungbleibtvonderStandby-Funktionunbeeinflusst.
Stammleitungsausgänge
• DemPowerBasisgerätliegen13DC-entkoppelteAbschlusswiderständebei.Damit
sind die Stammleitungen abzuschließen!
LNB remote power supply
3 operation modes can be chosen for the LNB remote power supply:
12V: All12IFinputs(1...12)carry12voltsremotepowersupply(forQuattro-LNB).
18V: VerticalIFinputscarry14volts,horizontalIFinputscarry18volts
22 kHz: Same as switch position 18 volts, but the high - band inputs are 22 kHz modu-
lated (for QUAD - LNB)
The switch position does not affect the control signals of the receiver!
The adequate LNB remote power voltage can be set for operation modes „Standby“
or „Always On“.
FortheLNBremotepowersupply,remotepowerof1200mAintotalisavailable(maxi-
mum 400 mA per LNB system)
Selective standby function
• Thelaunchamplifierfeaturesaselectivestandbyfunction.
Example: If all participants only watch TV programs of SAT system A, only the dedi-
cated LNB is supplied with power. The internal logic turns off the power supply of all
other LNBs as well as that of the integrated amplifiers. This process saves a great
deal of energy!
Standby function signaling
• Theterrestrialdistributionisnotaffectedbythestandbyfunction.
Trunk line outputs
• Thelaunchamplifierissuppliedwith13DCisolatedterminatingresistorsfortermi-
nating the trunk lines!
FürSAT-Systeme A B C
Über Stammleitung 1 5 9
Hilfsspannung 12 Volt in der gesamten
Kaskade über Stammleitung
2 6 10
ForSATsystem A B C
Via trunk line 1 5 9
Auxiliary voltage 12 volts within
the whole cascade via trunk line
2 6 10