Specifications

TM
2
2
TM
Einstellhinweise:
Stromversorgung LNB
Schalterstellungen:
Für die LNB-Fernspeisung sind 3 Betriebsarten wählbar:
12 V: Alle 4 ZF-Eingänge führen 12 Volt Fernspeisung (Betriebsart für
Quattro LNB).
18 V: Die vertikalen ZF-Eingänge führen 12 Volt und die horizontalen
ZF-Eingänge führen 18 Volt.
22 kHz: Wie Schalterstellung 18 Volt, jedoch sind die High-Band Eingänge
mit 22 kHz moduliert (Betriebsart für QUAD).
Die Schalterstellung hat keinen Einfluss auf die Steuersignale des
Receivers!
Die zutreffende LNB-Fernspeisespannung kann für die
Betriebsfunktionen “Standby” oder “Dauerbetrieb” =Always On
eingestellt werden.
Bei Vorgängerversionen nur Standby Betrieb möglich.
Bitte beachten Sie das Geräteetikett.
Der LNB-Fernspeisestrom darf insgesamt 0,6 A und der maximal zulässi-
ge Strom auf einer Buchse darf 0,4 A beim SBK 5502 NF und 0,5 A beim
SBK 5503 NFI nicht überschreiten.
Eingangspegel
Das Basisgerät SBK 5503 NFI verfügt über Synchronpegelsteller, um die
unterschiedlichen Pegel der verschiedenen Bänder (Low-Band; High-Band)
anzugleichen. Pro Band steht ein Regler zur Verfügung. Die Eingangspegel
können um 0...10 dB reduziert werden. Die Version SBK 5502 NF besitzt für
jeden SAT-ZF-Eingang separate Pegelsteller. Stellbereich: 0 ... -8 dB.
Um den Pegel der terrestrischen oder BK-Signale anzupassen, sind die
Basisgeräte mit einem Pegelsteller ausgestattet. Die Eingangspegel können
im aktiven Betrieb um 0...10 dB reduziert werden.
Bitte beachten Sie den Anleitungsteil „Terrestrik“!
12 V 22 kHz
18 V
12 V22 kHz
18 V
Standby
Dauerbetrieb/
Always On
Synchron
Low-Band
Synchron
High-Band
-10 dBTerr.
passiv
Setting instructions:
Power Supply to LNB
3 operation modes can be chosen for the LNB remote power supply:
12 V: All 4 IF inputs carry 12 volts remote power supply (for
Quattro LNB).
18 V: Vertical IF inputs carry 12 volts, horizontal IF inputs carry
18 volts.
22 kHz: Same as controller position 18 volts, but the high-band
inputs are 22 kHz modulated (for QUAD-LNB).
The controller position does not affect the control signals of
the receiver !
The adequate LNB remote power voltage can be set for
operation modes “standby” or “Always on”.
Previous versions only with “standby” mode.
Please pay attention to the label.
The LNB remote current must not exceed a total of 0,6 A and the
maximum permissible current per socket must not exceed 0,4 A for the
SBK 5502 NF and 0,5 A for the SBK 5503 NFI.
Input Levels
The SBK 5503 NFI has a synchronous level attenuator in order to match the
different levels of the various bands (low band, high band). There is one con-
troller per band. The input levels can be reduced by 0 ... 10 dB.
The SBK 5502 NF has a separate level attenuator for each SAT-IF-input.
Level adjustment range: 0 ... -8 dB.
The launch amplifiers are equipped with an adjustable attenuator in order to
adjust the level of the terrestrial or CATV signals.
The input levels can be reduced in active mode by 0 ... 10 dB.
Please take note of the „Terrestrial“ section of the instructions.
12 V 22 kHz
18 V
12 V22 kHz
18 V
Standby
Dauerbetrieb/
Always On
Synchron
Low-Band
Synchron
High-Band
-10 dBTerr.
passiv