I Preface This electric height adjustable standing desk consists of a heavy-duty steel desk frame and a motorized height adjustment system. Please read and completely understand this manual before installation in order to make sure the safe and correct use of the system and maintain the longevity of the overall construction and the built-in electronics. Instructions of Safety and Warnings: * Any failure to comply with the safety and installation instructions in this manual may cause serious bodily injury.
I Preparation o ‘What are the specifications you need to know? | 9 ‘What are the tools you require while Installation? ‘Weight Capacity Power Input Operation Temperature 100kyg (2201bs) {100-240V) E5) o Bubble Level Allen Wrench Drill Phillips Screwdriver (Included) o ‘What's the thing you'd better have before Installation? A Shipping Blanket to protect the desk and the floor o Things you need to know before installation Please check all of the components shown in the component hacktivist, If any of the com
$-D (x6) Phillips Head Screw Philips Head Screw-+ 1 Spacer | Cable Sip Now let’s start the installation. I Attaching Side Brackets Shipping Blanket * Please prepare a spacious area for installation, and put a shipping blanket on the area to prevent scratches on the floor and the frame. * Unpack the crossbar, and carefully place it on the floor. Attach the side bracket to the end of the crossbar. Please don’t screw it now. * Repeat the same process to assemble the other side bracket.
I Drilling Mounting Holes « Place the assembled frame on the back of the tabletop. « Ensure that the frame is placed in the center of the table. Allen Wrench « Then adjust the frame to suit the size of the tabletop. When adjusting the frame position, please mace sure It doesn’t exceed the range of kits screen printing. Loosen the hex head screws that fix the adjustable junction, but don't completely take out the screws.
T~ Re tighten all the hex head screws to finish the adjustment. Drill After tightening the screws, use a drill to make mounting holes on the backside of the tabletop through the 8 mounting holes on the side brackets. Note: The depth of the mounting holes should be over 10mm and the diameter should be less than 3mm.
1 Assembling the Lifting Columns Allen Wrench « Remove the tabletop for further Installation. « Insert the two lifting columns into the two ends of the crossbar with the heads of the [lifting columns facing Inward. Make sure the mounting holes on the lifting columns completely align with the screw holes on the crossbar. « Fix the lifting column and the side bracket with crossbar using 4 S-A screws with the Allen wrench. * Repeat the same process to assemble the other lifting column.
I Assembling the Fixing Plate * Align the mounting holes on the fixing plates with the screw holes as shown, * Attach the fixing plate on the center of the crossbar with 2 $-D screws using a Phillips screwdriver. Note: The arrow on the fixing plate indicates the direction of sliding in the control bax. Folio the direction of the arrow to mount the control box in the next step. The fixing plate can be attached to ether of the right side and the left side.
I Assembling the Cable Management Tray Align the fixing plate with the right end of the control box's soot. Slide the control box into the fixing plate from the left until the control box can't be moved the attachment Is complete. Align the mounting holes on the tray hangers with the screw holes &) on the cable management tray. Assemble the tray hangers to the cable management tray with 4 5-D screws from below using a Phillips screwdriver.
17 Tighten the knobs on the tray hangers. 1 Assembling the Desktop Attach the 5-C natl-vibratlon pad to the surface of the crossbar on the ten positions as shown.
« Allen the previously drilled screw holes with » Attach the controller to the desktop with 2 S-B screws using a driller. the mounting holes on the crossbar. Insert » Stick the adhesive S-E cable clip under desk to organize cords. and tighten the 4 S-B screws from below. * Repeat the same process to tighten the other side of the desktop.
I Low Profile Adjustment There are two adjustable fat pads under each foot. If the orifice isn't even, simply turn the pad to adjust the height to make the desk stable Tip: Use & bubble level to check if the desktop is even. Connect the desk to power. You can now use the sit-stand desk. Note: We have another manual of the digital controller for detailed instruction. Please check the Digital Control Panel For Electric Height Adjustable Desk User Guide.