Owner`s manual

PRINTER’S INSTRUCTIONS:
INSTR,INSTL,IRE-2.0 • LINEAR P/N: 223109B • INK: BLACK •
MATERIAL: 20LB. GLOSS WHITE PAPER • SIZE: 4.25” X 17.500” FOLD TO 4.250” X 3.500”
• FOLDING: 5 PARALLEL FAN-FOLDS, FINISH WITH LOGO SHOWING • SCALE: 1-1
223109B • IMAGE 2
IR Controlled Components
IR Sensor
Window
Fig. 5a IRE-2.0 attached directly
to IR sensor window
Cabinet Door
Fig. 5b IRE-2.0 attached to inside of
cabinet door directly opposite
IR sensor window
IRE-2.0 attached to shelf directly
below or above IR sensor window
Fig. 5c & d
Fig. 5
Fig. 5
Low
output side
toward IR
sensor
Connecting
lead
Emitter
Shell
High
output
side
Internal
IR Emitter
Use the higher power setting (NOT Blaster Power) on the connecting
block or terminator, if so provided.
Some installers like the option of placing the emitter completely inside
a component, as near as possible to the IR sensor, for a clean external
appearance. In some cases, the whole emitter can be so placed.
Fig. 4
IRE-2.0
Dual IR Emitter
SmartPath
™
INSTALLATION INSTRUCTIONS
2
940 Columbia Avenue, Riverside, CA 92507
•
Phone [phone]
•
Fax [phone]
www.speakercraft.com
LIMITED 5-YEAR WARRANTY
SpeakerCraft Inc. warrants to the original retail purchaser only that this SpeakerCraft
product will be free from defects in materials and workmanship, for a period of 5-
years, provided it was purchased from a SpeakerCraft Authorized Dealer.
Defective products must be shipped, together with proof of purchase, prepaid
insured to the SpeakerCraft Authorized Dealer from whom they were purchased, or
to the SpeakerCraft factory at the address listed on this installation instruction manual.
Freight collect shipments will be refused. It is preferable to ship this product in the
original shipping container to lessen the chance of transit damage. In any case,
the risk or loss or damage in transit is to be borne by the purchaser. If upon examina
-
tion at the Factory or SpeakerCraft Authorized Dealer it is determined that the unit
was defective in materials or workmanship at any time during this warranty period,
SpeakerCraft or the SpeakerCraft Authorized Dealer will, at its option, repair or replace
this product at no additional charge, except as set forth below. If this model is no
longer available and can not be repaired effectively, SpeakerCraft, at its sole option
may replace the unit with a current model of equal or greater value. In some cases
where a new model is substituted, a modification to the mounting surface may be
required. If mounting surface modification is required, SpeakerCraft assumes no
responsibility or liability for such modification. All replaced parts and product
become the property of SpeakerCraft Inc. Products replaced or repaired under this
warranty will be returned to the original retail purchaser, within a reasonable time,
freight prepaid.
This warranty does not include service or parts to repair damage caused by accident,
disaster, misuse, abuse, negligence, inadequate packing or shipping procedures,
commercial use, voltage inputs in excess of the rated maximum of the unit, or service,
repair or modification of the product which has not been authorized or approved by
SpeakerCraft. This warranty also excludes normal cosmetic deterioration caused by
environmental conditions. This warranty will be void if the Serial number on the
product has been removed, tampered with or defaced.
This warranty is in lieu of all other expressed warranties. If the product is defective in
materials or workmanship as warranted above, the purchaser’s sole remedy shall be
repair or replacement as provided above. In no event will SpeakerCraft be liable for
any incidental or consequential damages arising out of the use or inability to use the
product, even if SpeakerCraft Inc. or a SpeakerCraft Inc. Authorized Dealer has been
advised of the possibility of such damages, or for any claim by any other party. Some
states do not allow the exclusion or limitation of consequential damages, so the above
limitation and exclusion may not apply. All implied warranties on the product are
limited to the duration of this expressed warranty. Some states do not allow limitation
on the length of an implied Warranty. If the original retail purchaser resides in such a
state, this limitation does not apply.
In others, it may be necessary to remove the internal emitter from its
shell so that it will fit in tiny chassis places. In this case, use the thin
edge of a knife to carefully pry the lower cover from the shell of the
emitter. Gently ease the tiny emitter and lead from it’s nest within the
shell. Use heat shrink tubing, or other insulating means, to prevent
shorting of the exposed leads.
Note 4: The emitters on the IRE-2.0 are wired in series. If you cut
one off, you will need to short the cut-off wires together for the
other one to operate.
Note 5: The emitter shell and EZ-Docker
™
port, though dark in
appearance, are transparent to Infrared. This allows IR commands
to pass through them, permitting local hand held remote control as
well as through the IRE-2.0.
LIT03200 (rev1)
223109B
ELT03200
SpeakerCraft
SpeakerCraft
®
®
Other Emitter Placements
Since the IRE-2.0 has high output from it’s curved top (See Fig. 4),
you may attach it to other surfaces nearby, if the installation permits.
(See Fig. 5)