Installation Guide

ManualsBrandsSpeakman ManualsPlumbingNeo Universal Shower Valve Trim Kit in Polished Chrome

INSTRUCTIONS FOR MODELS

NEED HELP?

92-CPT-1000-UNI-D-R2

For additional assistance or service please contact:

SPEAKMAN

Company

400 Anchor Mill Road

New Castle, DE 19720

800-537-2107

customerservice@speakman.com

www.speakman.com

CPT-1000-UNI

CPT-1300-UNI

Delta Installation

TOOLS AND SUPPLIES

IMPORTANT

SAFETY TIPS

Cover your drain to prevent loss of parts. Be sure to

always wear proper eye protection.

MAINTENANCE

Your new Valve Trim is designed for years of

trouble-free performance. Keep it looking new by

cleaning it periodically with a soft cloth. Avoid

abrasive cleaners, steel wool, and harsh chemicals as

these will dull the finish and void your warranty.

WARRANTY

Additional warranty information can be found at:

www.speakman.com

Phillips

Screwdriver

• Circular Trim Package shown for reference. While

the appearance of your trim may be different, the

installation steps are the same.

• This Trim Package is intended to mount only to the

following Delta valves. Please verify the model of

your valve prior to installation.

DELTA

MultiChoice

R10000-UNBX

R10000-UNBXHF

R10000-UNWS

R10000-UN

R10000-UNWSHF

*NOT FOR USE WITH DIVERTER/VOLUME CONTROL MODELS

• Verify that existing Valve is installed

correctly per manufacturers instructions. If

valve is not installed correctly, installation of

the Universal Valve Trim may not be possible.

Verify that your existing Delta Valve has the correct Cartridge installed. The Universal Valve Trim

will only work with Delta’s single function cartridge. If your Valve has a Dual Function Cartridge,

you must replace the cartridge with a Delta 1300/1400 Series Cartridge.

1300/1400 CARTRIDGE

1300/1400 MULTI-CHOICE CARTRIDGE

CORRECT SINGLE FUNCTION

CARTRIDGE TO USE.

DUAL FUNCTION CARTRIDGE

CANNOT BE USED WITH SPEAKMAN

UNIVERSAL VALVE TRIM

REPLACE WITH 1300/1400 CARTRIDGE

OR 1300/1400 MULTICHOICE CARTRIDGE

1700 CARTRIDGE

17 MULTI-CHOICE CARTRIDGE

DUAL FUNCTION THERMOSTATIC

CARTRIDGE CANNOT BE USED WITH

SPEAKMAN UNIVERSAL VALVE TRIM.

REPLACE WITH 1300/1400 CARTRIDGE

OR 1300/1400 MULTICHOICE CARTRIDGE

17T CARTRIDGE

Remove existing Delta Trim Package. Unthread and remove existing Bonnet Collar from Delta

Valve.

Clean front surface of wall. Ensure that the Delta Valve Stops (3) are in the open position by

unthreading Valve Stop counter-clockwise. Install Valve Mounting Plate (1) to existing Delta Valve,

using the 10-24 x 1-½” screws (2) provided. Take care to not over tighten mounting screws or

damage may occur.

NOTE: Depending on the mounting depth of the Delta Valve, the Valve Mounting Plate (1) may contact

either the surface of the wall, or the Plaster Guard of the Delta Valve when secured into the final position.

Summary of content (13 pages)

PAGE 1
INSTRUCTIONS FOR MODELS CPT-1000-UNI CPT-1300-UNI Delta Installation TOOLS AND SUPPLIES 1 Phillips Screwdriver Verify that your existing Delta Valve has the correct Cartridge installed. The Universal Valve Trim will only work with Delta’s single function cartridge. If your Valve has a Dual Function Cartridge, you must replace the cartridge with a Delta 1300/1400 Series Cartridge. CORRECT SINGLE FUNCTION CARTRIDGE TO USE.
PAGE 2
4 7 Re-assemble the Bonnet Collar to the Delta Valve. Orient the Decorative Wall Plate (1) as shown below and insert the RED index button into the top hole of the Wall Plate, and the BLUE index button into the lower hole. Slide Wall Plate Assembly over Wall Mounting Plate (2). RED BLUE 5 Secure the Wall Mounting Plate (1) to the Valve Mounting Plate (2) using the 8-32 X 1-1/8” Screws (3) provided.
PAGE 3
REPAIR PARTS •RPG10-0117 ROUGH-IN DIMENSIONS: CPT-1000-UNI 41" 2 114mm ROUGH-IN DIMENSIONS: CPT-1300-UNI 45" 8 117mm 71" 4 186mm 71" 4 186mm 21" 4 56mm 2" 51mm 71" 4 186mm 31" 2 89mm 31" 2 89mm 1" 25mm •Dimensions are subject to change without notice. 11" 8 28mm •Dimensions are subject to change without notice.
PAGE 4
INSTRUCTIONS FOR MODELS CPT-1000-UNI CPT-1300-UNI Kohler Installation TOOLS AND SUPPLIES Drill Drill Bit Ø1/4” (0.25”) 1 Using a Ø1/4” (ø.25”) Drill Bit, enlarge the 4 holes shown below in the existing Kohler Mounting Flange. 2 Clean front surface of wall. Install Valve Mounting Plate (1) to existing Kohler Valve, using the 10-24 x 1-½” screws (2) provided. Take care to not over tighten mounting screws or damage may occur.
PAGE 5
4 The Universal Valve Trim kit includes two (2) Spindle Adapters that allow for both shallow and deep valve mount installations. Measure the distance between the front lip of the Wall Mounting Plate and the end of the Kohler Spindle as shown below to determine which Spindle Adapter is to be used. 6 Orient the Decorative Wall Plate (1) as shown below and insert the RED index button into the top hole of the Wall Plate, and the BLUE index button into the lower hole.
PAGE 6
REPAIR PARTS •RPG10-0114 ROUGH-IN DIMENSIONS: CPT-1000-UNI 41" 2 114mm ROUGH-IN DIMENSIONS: CPT-1300-UNI 45" 8 117mm 71" 4 186mm 71" 4 186mm 21" 4 56mm 2" 51mm 71" 4 186mm 31" 2 89mm 31" 2 89mm 1" 25mm •Dimensions are subject to change without notice. 11" 8 28mm •Dimensions are subject to change without notice.
PAGE 7
INSTRUCTIONS FOR MODELS CPT-1000-UNI CPT-1300-UNI Moen Installation TOOLS AND SUPPLIES 1 Assemble Moen Adapter (1) to the Valve Mounting Plate (2) taking care to orient it as shown below. Press spring tabs of the Moen Adapter (1) thru the corresponding holes in the Valve Mounting Plate (2). 2 Clean front surface of wall. Install Valve Mounting Plate Assembly (1) to existing Moen Valve (2), using the 8-32 x 2-½” Screws (3) provided.
PAGE 8
3 Secure the Wall Mounting Plate (1) to the Valve Mounting Plate (2) using the 8-32 X 5/8” Screws (3) provided. 5 The Universal Valve Trim kit includes two Spindle Adapters that allow for both shallow and deep mount installations. Observe the distance between the front lip of the Wall Mounting Plate and the end of the Moen Spindle Hub as shown below to determine which Spindle Adapter to use.
PAGE 9
6 Confirm that the Valve is in the correct orientation as described in Step 4. Insert Spline Adapter (1) over Moen spindle (2), aligning it to the flats on the Moen Spindle (2). The extended “lug” on the Spindle Adapter (1) should be positioned to the left of the Moen Valve Stop (4). One set of splines on the adapter must be oriented perfectly vertical when installed, as shown below. Secure the Spline Adapter with the 10-24 X 1/2” Screw (3) provided.
PAGE 10
REPAIR PARTS •RPG10-0115 ROUGH-IN DIMENSIONS: CPT-1000-UNI 41" 2 114mm ROUGH-IN DIMENSIONS: CPT-1300-UNI 45" 8 117mm 71" 4 186mm 71" 4 186mm 21" 4 56mm 2" 51mm 71" 4 186mm 31" 2 89mm 31" 2 89mm 1" 25mm •Dimensions are subject to change without notice. 11" 8 28mm •Dimensions are subject to change without notice.
PAGE 11
INSTRUCTIONS FOR MODELS CPT-1000-UNI CPT-1300-UNI Symmons Installation TOOLS AND SUPPLIES Phillips Screwdriver 1 Flat Tip Measuring Screwdriver Tape Clean front surface of wall. Verify that Symmons Valve Stops (4) are in the “Open” position by turning counter-clockwise. Install Valve Mounting Plate (1) to existing Symmons Valve, using the 8-32 x 1-3/8” screws (2), and Washers (3) provided. Take care to not over tighten mounting screws or damage may occur.
PAGE 12
3 The Universal Valve Trim kit includes two (2) Spindle Adapters that allow for both shallow and deep valve mount installations. Measure the distance between the front lip of the Wall Mounting Plate and the end of the Symmons Spindle as shown below to determine which Spindle Adapter is to be used. 5 Orient the Decorative Wall Plate (1) as shown below and insert the RED index button into the top hole of the Wall Plate, and the BLUE index button into the lower hole.
PAGE 13
REPAIR PARTS •RPG10-0116 ROUGH-IN DIMENSIONS: CPT-1000-UNI 41" 2 114mm ROUGH-IN DIMENSIONS: CPT-1300-UNI 45" 8 117mm 71" 4 186mm 71" 4 186mm 21" 4 56mm 2" 51mm 71" 4 186mm 31" 2 89mm 31" 2 89mm 1" 25mm •Dimensions are subject to change without notice. 11" 8 28mm •Dimensions are subject to change without notice.