Installation Guide

ManualsBrandsSpeakman ManualsBathSensorFlo Battery-Powered Sensor Faucet in Polished Chrome

Page 1 of 15

SPEAKMAN

400 Anchor Mill Rd. New Castle, DE 19720 Phone: 800-537-2107 Fax: 800-977-2747

1/15/16 www.speakman.com 92-S-9100-9200-05

SPEAKMAN

S-9100-CA, S-9100-CA-E, S-9200-CA, S-9200-CA-E

Installation, Maintenance & Operation Instructions

SENSORFLO® BATTERY or AC POWERED SLIM DESIGN FAUCETS with DIFFERENT OPTIONS

DESCRIPTION

Speakman SENSORFLO® faucet featuring a Solenoid and Power pack that are readily serviceable from

under the counter. Integral Hot and Cold mechanical mixing valves, Hot and Cold water supply check valves,

standard inline filters, and a new Sensor Module design incorporated into solid brass Faucet body make it

ideal for public areas such as schools, hotels, laboratories, and hospitals.

Speakman SENSORFLO

Slim Design Faucets are available in several Faucet Spout shapes such as:

Gooseneck, Modern Tubular or Cast C-Spout, all with a Sensor Module installed inside.

The solid brass spout body contains the Sensor Module. The Solenoid and the Power Supply (Batteries or

AC/DC adapter) are located under the sink with easy accessibility. The Sensor module is powered by two (2)

3-volt DC lithium batteries or AC/DC adaptor with waterproof connectors housed in a separate Power

Module attached under counter, and mounted onto the Solenoid body. There is a low battery warning light

that pulsates before the batteries are depleted and keeps pulsating for at least 2 weeks after they are no

longer in service.

OPERATION

Speakman SENSORFLO

faucets are thoughtfully designed and engineered in accordance with the highest

quality and performance standards. It requires no handles to turn, lift or push. Built in vandal resistant

circuitry shuts off the water after continuous flow of approximately 60 seconds. This feature prevents

flooding. (The water is easily turned on again by placing one’s hands under the lavatory spout)

Water conserving vandal resistant recessed aerator reduces water flow to 2.2 GPM / 8.4 LPM to meet

requirements of ANSI A112.18.1M for flow rates. There is a inline filter on the Solenoid that is readily accessible

for maintenance purposes. ADA (American Disabilities Act) compliant. NOTE: Stainless steel hoses are

optional.

SPECIFICATIONS

INLET SUPPLY: 3/8” COMPRESSION WITH MALE THREADS for Cold and Hot Water

FLOW RATE: 2.2 GPM / 8.4 LPM

FINISH: BRASS CHROME PLATED

Options:

Less Transformer (for use with multi-unit

transformers)

LF Vandal Resistant Laminar 1.5 GPM Flow Control

3 Stainless Steel Hoses for use with Tee or

Mixer

ELF Vandal Resistant Laminar 1.2 GPM Flow Control

HTS 1 Stainless Steel Flexible Hose

T Tee with Checks

Vandal Resistant 1.5 GPM Aerator Outlet

Device

Summary of content (15 pages)

PAGE 1
Page 1 of 15 SPEAKMAN ® S-9100-CA, S-9100-CA-E, S-9200-CA, S-9200-CA-E Installation, Maintenance & Operation Instructions SENSORFLO® BATTERY or AC POWERED SLIM DESIGN FAUCETS with DIFFERENT OPTIONS DESCRIPTION Speakman SENSORFLO® faucet featuring a Solenoid and Power pack that are readily serviceable from under the counter.
PAGE 2
Page 2 of 15 All models of faucets are also available with the following combinations of options. NO Deck Plate 4” Deck Plate 8” Deck Plate UCM (under counter mixing valve with built-in backflow check valves) TMV (thermostatic mixing valve for more consistent water temperature with check valves) ACM (above counter mixer) MO (manual override) Three different shapes of Faucets, all made of solid polished chrome brass can be mounted onto a unique Central Base with the Infrared Sensor Module.
PAGE 3
Page 3 of 15 INSTALLATION INSTALLATION OF AERATOR Install vandal resistant aerator into the outlet of the faucet with the provided Speakman aerator wrench INSTALLATION OF POWER MODULE TO SOLENOID If the Power Module (either battery or AC) is not pre-installed onto Solenoid body, attach it as shown with the #8 provided screws. (2) INSTALLATION OF FAUCET Insert the faucet shank into a 1-1/8” hole with connector wires going in first, taking care to not pinch the wires.
PAGE 4
Page 4 of 15 Under sink, place rubber wire guard (with notch facing forward) and pass the wires through notch. The wires should be inside the channel of the rubber wire guard to prevent pinching when tightening. Insert metal washer and tighten the locknut to provide tension into the rubber guard. While tightening make sure the position of Faucet on top of counter is straight. Verify that no connector wires are pinched.
PAGE 5
Page 5 of 15 Install 3/8”compression fitting hoses to the UCM (under counter mixing valve). The hot and cold sides are marked H and C. Hand tighten connections and then slightly tighten with an adjustable wrench. DRY CONNECTION ONLY. NOTE: During winter month it may be necessary to reverse Hot and Cold connections to obtain warmer temperature range of water. After connecting to supply lines, turn on the water and activate the faucet with your hands, checking for leaks.
PAGE 6
Page 6 of 15 After screw has been removed from the unit, pull up faucet body top. There are 2 O-Rings on the shank and one around the lenses of Sensor Module that should be replaced if damaged. Remove the 2 screws on the clamp. After removing, pull up the Sensor Module from the central shank (do not damage the O-Rings and the wire connectors). Reassemble new Module with care not to cut wires through the big holes into the Base, and then insert the clamp with the Sensor over the shank.
PAGE 7
Page 7 of 15 With the cover of the power module removed, remove the dead batteries and replace them with new batteries (ensure that the position of the new batteries matches the marks + and - on the cover). Replace the cover on Power Module. ROUGH-IN DIMENSIONS SPEAKMAN ® 400 Anchor Mill Rd. New Castle, DE 19720 Phone: 800-537-2107 Fax: 800-977-2747 1/15/16 www.speakman.
PAGE 8
Page 8 of 15 INSTALLATION OF OPTIONS ACM (ABOVE COUNTER MIXER) INSTALLATION 1. With the Flange Nut, steel washer and rubber washer on the shank, install ACM from the bottom. 2. Tighten the top Flange Nut adjusting the proper height above counter. 3. Tighten then the bottom Flange Nut until the assembly is fixed in place. 4. Insert the Handle and tighten with the screw onto the shank. 5. Snap the screw cover onto Handle. 6. Attach the Hot and Cold hoses from supply line to ACM (see marks on body) 7.
PAGE 9
Page 9 of 15 MO (MANUAL OVERRIDE) INSTALLATION 1. Thread a Thin Nut onto the Faucet Shank. . 2. Insert Mount bracket over Faucet Shank. Secure into position with the Solenoid Nut. (dry connection only) 3. Lower the Thin Nut onto bracket 4. Slip compression spring onto MO spindle 5. With O-Ring attached to the Spacer, slip Spacer and Bearing Sleeve onto spindle 6. With the lock washer and screw inside the Handle, properly position Handle onto Spindle. 7.
PAGE 10
Page 10 of 15 UCM (UNDER COUNTER MIXER) WITH MO (MANUAL OVERRIDE) INSTALLATION 1. Install the MO as described above. 2. Install the UCM fixed on the wall with the Clamp in the desired position. 3. The UCM it is marked with H and C for hot and cold supply lines. The mixed water exits on top into the Tee. 4. The water supply splits into the Tee: -one exit hose goes to Solenoid and the other hose goes to bottom of MO. 5.
PAGE 11
Page 11 of 15 ACM (ABOVE COUNTER MIXER) WITH MO (MANUAL OVERRIDE) INSTALLATION 1. Install the MO and ACM as described above. (NOTE: In this case the ACM has an extra By-pass outlet: -in total 2 branches of mixed water.) 2. There are two branches with mixed water: -one goes to Solenoid inlet, and the other goes to bottom of MO. 3. Form the side of MO the by-pass hose goes to the upper side of Solenoid discharge for manually controlled side.
PAGE 12
Page 12 of 15 HOSE INSTALLATION BETWEEN MO (MANUAL OVERRIDE) AND ACM (ABOVE COUNTER MIXER) OR UCM (UNDER COUNTER MIXER For ease of installation attach hoses to ACM (above counter mixer) and MO (manual override) diverter before installing under the sink. 1. Attach hot supply hose 1 to inlet ports of mixer (H port) 1 either ACM or UCM. 2. Attach cold supply hose 2 to inlet ports of mixer (C port) 2 either ACM or UCM. 3.
PAGE 13
Page 13 of 15 REPAIR PARTS PART/GROUP NUMBER RPG05-0837-PC RPG38-0128-PC A-EA12 A-ELF RPG05-0851-PC RPG76-0033-LBL RPG 76-0039 RPG 66-0044 RPG66-0168 RPG66-0169 13/16 -1.5 GPM Aerator repair group 13/16 -0.5 GPM Boca repair group A-EA12 A-ELF 1.
PAGE 14
Page 14 of 15 TROUBLESHOOTING Before calling Speakman Company for service, please run through the following checklist of troubleshooting steps. IF WATER FLOW FROM THE FAUCET DECREASES: 1. 2. Make sure the supply stops are open. Ensure both the hot and cold water Temperature Adjusters are not in the closed position (to open, screw out the hot and cold water Temperature Adjusters (counter-clockwise direction) 3. Check that the In-line Filter in the Solenoid body is not blocked with debris.
PAGE 15
Page 15 of 15 QUESTIONS & ANSWERS Q. How does the Sensorflo® faucet work? A. It uses infrared technology. The sensor emits a non-visible beam of light. When an object enters the detection area, the sensor signals the solenoid valve to open for water to flow. When an object leaves the detection area, the sensor signals the valve to close. Q. Is the Speakman Sensorflo® faucet sensor beam adjustable? A. No, the Speakman Sensorflo® faucet sensor beam is not adjustable.