Installation

ManualsBrandsSpeakman ManualsPlumbingCommander Collection 0.5 GPM Deck Mounted Widespread Bathroom Faucet with Wrist Blade Handles

INSTRUCTIONS FOR MODELS

92-SC-300X-LD-05

For additional assistance or service please contact:

SPEAKMAN

800-537-2107

customerservice@speakman.com

www.speakman.com

SC-3002-8-LD

SC-3002-8-LD-E

SC-3004-8-LD

SC-3004-8-LD-E

SC-3004-FC-LD

SC-3004-LD

SC-3004-LD-E

HELPFUL TOOLS & SUPPLIES:

TOOLS AND SUPPLIES

Phillips

Screwdriver

Adjustable

Wrench

Slip Joint

Wrench

Aerator

Wrench

(supplied)

Basin

Wrench

Tubing

Cutter

Supply

Hoses

Safety

Glasses

Thread Seal

Tape

Solder Kit

Warranty information can be found at:

www.speakman.com

WARRANTY

MAINTENANCE

Your new Speakman Product is designed for years of

trouble-free performance. Keep it looking new by

cleaning it periodically with a soft cloth. The use of harsh

chemicals and abrasives on any of the Speakman custom

finish products may damage the finish and void the

product warranty. Please be sure to only use approved

cleaners. Please contact Speakman for any clarification

of acceptable cleaners.

Cover your drain to prevent loss of parts. Be sure to

wear eye protection while cutting pipe.

SAFETY TIPS

IMPORTANT

This installation manual covers several models.

While the appearance of your faucet may

vary, the installation steps required are the

same as shown in this manual.

Be sure to read instructions thoroughly before

beginning installation.

Do not overtighten any connections or damage

may occur.

This faucet has an operating range of 20-80 psi.

Remove the Compression Nuts (1) from the inlets

of the end body valves.

Remove Compression Nuts (1) from End Bodies.

Retrieve the Tee Assembly bag group. Slide a

Compression Nut (1), followed by a

Compression Sleeve (2) over the copper pipe of

each end of the Tee Assembly.

Summary of content (4 pages)

PAGE 1
INSTRUCTIONS FOR MODELS SC-3002-8-LD SC-3002-8-LD-E SC-3004-8-LD SC-3004-8-LD-E SC-3004-FC-LD SC-3004-LD SC-3004-LD-E TOOLS AND SUPPLIES Phillips Screwdriver Adjustable Wrench Slip Joint Wrench IMPORTANT This installation manual covers several models. While the appearance of your faucet may vary, the installation steps required are the same as shown in this manual. Do not overtighten any connections or damage may occur.
PAGE 2
3 Bench assemble the Tee to the HOT and COLD end body valves. Be sure to fully seat the copper piping into the end body valves, and hand tighten Compression Nuts (1) to the outlet ports. Be sure the end body valves are perpendicular to the Tee assembly. 4 Insert and position the Gooseneck Flange (1) with Gasket (2) down through the center hole of the sink or counter top, being sure the cut out of the gasket is aligned to the rear of the faucet.
PAGE 3
11 From above the sink, place decorative Flange (1), then screw Escutcheon (2) onto end body valve assemblies and hand tighten. Slip Trim Sleeves (3) onto spindles. Position Handles (4), Lock Washers (5) (SC-3004 series) and use Screws (6) to secure to spindles. Position Index Buttons (7) on handles (blue on right handle, red on left handle) and press into place. 12 Assemble gooseneck to flange assembly by wrench tightening Gooseneck Collar Nut (1).
PAGE 4
SC-3002-8-LD ROUGH-IN DIAGRAM SPEAKMAN ® 81" 8 206mm 8" 203mm 21" 4 57mm 31" 8 79mm 1-1/2" (38mm) MAXIMUM DECK THICKNESS 3" 8 9mm 11" 8 29mm 73" 8 188mm 11 3 " 4 298mm 3" 8 9mm 45" 8 119mm 2" 51mm 21" 4 57mm 11" 2 38mm MAXIMUM DECK THICKNESS 11 " 16 17mm SPEAKMAN ® COLD INLET 53" 8 135mm 11 3 " 4 298mm " 12 1 2 317mm " 3" 8 9mm 2" 71 2 189mm 45" 8 119mm 21" 4 57mm 51mm HOT INLET COLD INLET DIMENSIONS SUBJECT TO CHANGE WITHOUT NOTICE.