Installation Guide

ManualsBrandsSpeakman ManualsBathNeo Single-Handle 3-Spray Shower Faucet in Polished Chrome (Valve Included)

SPEAKMAN

Phone: 800-537-2107 Fax: 800-977-2747

01/14/19 www.speakman.com 92C-SM-1010-01

SPEAKMAN

SM-1010

Installation, Operation & Maintenance Instructions

NEO™ COLLECTION COMBINATION SERIES

DESCRIPTION

Speakman Neo™ Collection Combination Series, SM-1010 includes: Shower Valve Trim (CPT-1001), Shower

Arm with Wall Flange (S-2540), and Low Flow Multi Function Shower Head (S-3010-E2). This combination

does include the Shower Valve.

This combination comes with the following Speakman

Sentinel Mark II® Pressure Balance Shower Valve

CPV-PB: Pressure Balance Shower Valve

Sweat & Thread Connections

SPECIFICATIONS

CPV-PB SENTINEL MARK II® PRESSURE BALANCE SHOWER VALVE:

COMPLIANCE: ASME A112.18.1 / CSA B125.1 Certified / ASSE 1016 Certified

CPT-1001 SENTINEL MARK II® SHOWER VALVE TRIM:

COMPLIANCE: ASME A112.18.1 / CSA B125.1 Standard

S-2540 SHOWER ARM WITH WALL FLANGE:

CONNECTIONS: ½” NPT Male Inlet & Outlet

S-3010-E2 LOW FLOW MULTI FUNCTION SHOWER HEAD:

CONNECTIONS: ½” NPT Female Inlet

FLOW RATE: 2.0 gpm (7.6 L/min)

COMPLIANCE: ASME A112.18.1 / CSA B125.1 Standard & WaterSense Certified

INSTRUCTIONS

See individual products for installation of the components and warranty information.

Summary of content (10 pages)

PAGE 1
SPEAKMAN ® SM-1010 Installation, Operation & Maintenance Instructions NEO™ COLLECTION COMBINATION SERIES DESCRIPTION Speakman Neo™ Collection Combination Series, SM-1010 includes: Shower Valve Trim (CPT-1001), Shower Arm with Wall Flange (S-2540), and Low Flow Multi Function Shower Head (S-3010-E2). This combination does include the Shower Valve.
PAGE 2
ROUGH-IN SPEAKMAN ® Phone: 800-537-2107 Fax: 800-977-2747 01/14/19 www.speakman.
PAGE 3
INSTRUCTIONS FOR MODELS TOOLS AND SUPPLIES CPV-PB CPV-PB-DV Pencil Keyhole Saw 1 IMPORTANT • Be sure to read instructions thoroughly before beginning installation. Adjustable Wrench Remove the two Screws with a Philips Head Screwdriver then slide the Rough-In Template off the Valve. • Be sure to have properly adjusted the Temperature Limiting Stop (TLS) as outlined in this Installation Manual. • Inspect all connections after installation of valve. • This valve has an operating range of 20-80 psi.
PAGE 4
6 PIPE FITTING INSTALLATION Connect the HOT and COLD Water Supply Lines ❷ (not included), the Shower Outlet Pipe ❸ (not included), and Tub Outlet Pipe ❹ (not included), by threading them into the Valve Body ❶ in a clockwise direction. Tighten the pipes to the Valve Body ❶ with a Pipe Wrench. Connect the Pipe Elbows ❺ (not included), to the end of the shower outlet and tub outlet pipes. If performing a shower only installation, install Plug Cap ❻ in place of tub outlet piping, as shown in STEP 5.
PAGE 5
10 FLUSHING THE WATER OUTLETS AND CHECKING FOR LEAKS 11 ADJUSTING THE TEMPERATURE LIMIT STOP (TLS) The maximum outlet temperature setting adjustment (Temperature Limit Stop (TLS)) of the Valve has been factory set at 110 °F. To adjust the limit of the maximum outlet temperature the Valve delivers, adjust the Valve’s temperature limit stop (TLS) collar by following the steps below. Place the Handle ❶ on the Valve Cartridge Spindle ❷ and turn the Handle ❶ clockwise to the full on mixed position.
PAGE 6
SPEAKMAN CPV-PB ROUGH-IN DIAGRAM ® A NOTES: COMPLIANCE: ASME A112.18.1/CSA B125.1 1" 25mm HOLE FOR SHOWER ARM ASSE1016/ASME A112.1016/CSA B125.16 6'-6" [2 METERS] TO FLOOR CONNECTIONS: 1/2" NPT MALE 1/2" SWEAT CONNECTIONS Hot/Cold Inlets: ½” Female Copper Sweat ½” NPT Male 5-1/2" (140MM) DIA.
PAGE 7
INSTRUCTIONS FOR MODELS CPT-1001 TOOLS AND SUPPLIES Phillips Screwdriver 1 Clean wall surface. Place Mounting Base (1) onto the valve, align mounting holes, and secure with supplied screws (2). Measuring Tape IMPORTANT • Do not over-tighten any connections or damage may occur. • Be sure to read instructions thoroughly before beginning installation. • Be sure to have properly adjusted the Temperature Limiting Stop (TLS) as per the Valve Installation Instructions before installing Valve Trim.
PAGE 8
SPEAKMAN CPT-1001 REPAIR PARTS ® ITEM NO. PART NO. DESCRIPTION RPG05-0874 SCREWS AND SPLINE ADAPTERS SPEAKMAN CPT-1001 ROUGH-IN DIAGRAM ® A 1" 25mm HOLE FOR SHOWER ARM R3 1 " 2 88.9mm 6'-6" [2 METERS] TO FLOOR 15 " 16 23.6mm 2" 50.4mm 51" 2 140mm HOLE FOR VAVLE ACCESS 7" 8 22.6mm 3 7 " 16 87mm 2" 51mm 31" 2 88.8mm 1" 2 12.7mm 1'-9" [533mm] 31" 2 88.4mm 5 13 " 16 147mm 2-1/2" [64mm] MINIMUM 3-1/2" [89mm] MAXIMUM ROUGH IN DEPTH 4'-6" [1.
PAGE 9
INSTRUCTIONS FOR MODELS TOOLS AND SUPPLIES S-2540 Thread Seal Tape 2 Apply Thread Seal Tape to inlet side of Shower Arm (1). ROUGH IN DIMENSIONS Allen Wrench (Included) IMPORTANT 2.25in 57.15mm REF Be sure to read instructions thoroughly before beginning installation. Do not overtighten any connections or damage may occur. SAFETY TIPS 3 Cover your drain to prevent loss of parts. Thread Shower Arm (1) into Female Pipe Fitting within the wall.
PAGE 10
INSTRUCTIONS FOR MODELS S-3010 S-3010-E2 S-3010-E175 TOOLS AND SUPPLIES Thread Seal Tape (included) 1 Apply Thread Seal Tape to the outlet side of shower arm in a clockwise direction. ROUGH IN DIMENSIONS Adjustable Wrench 5-1/2" 140mm IMPORTANT Be sure to read instructions thoroughly before beginning installation. Do not overtighten any connections or damage may occur. 2 6" 152mm Thread Shower head onto shower arm by turning it in a clockwise direction. Tighten with adjustable wrench.