Installation

ManualsBrandsSpeakman ManualsPlumbingSentinel Pro Collection 2.5 GPM Wall Mounted Shower System, Includes Diverter Trim, Showerhead, Handshower, in Polished Chrome

SPEAKMAN

400 Anchor Mill Rd. New Castle, DE 19720 Phone: 800-537-2107 Fax: 800-977-2747

12/04/17 www.speakman.com 92-SM-5450-01

SPEAKMAN

SM-5450

Installation, Operation & Maintenance Instructions

SENTINELPRO™ COMBINATION SERIES

DESCRIPTION

Speakman SentinelPro™ Combination, SM-5450, unites Anti-Scald Thermostatic / Pressure Balance Diverter

Shower/Bath Valve with integral Check Stops (CPV-TP-DV), Trim with integral Volume Control / Diverter

Handle (CPT-5401), Hand Shower with flow control (VS-100-PC), Supply Ell (VS-115), In-line Vacuum Breaker

(VS-117), Swivel Connector (VS-120); 30in Slide Bar (VS-123), Tub Spout (S-1554), and 69in Metal (SS) Hose.

SPECIFICATIONS

CPV-TP-DV ANTI-SCALD THERMOSTATIC / PRESSURE BALANCE DIVERTER SHOWER VALVE:

CONNECTIONS: ½” Female Copper Sweat and ½” NPT Male at both the Inlets (Cold, Hot) & Outlets

(Shower, Tub)

FLOW RATE: 1.5 gpm (5.7 L/min) or higher

COMPLIANCE: ASSE 1016 / ASME A112.1016 / CSA B125.16 & ASME A112.18.1 / CSA B125.1 Standards

CPT-5401 T/P DIVERTER VALVE TRIM:

FINISH: Polished Chrome

COMPLIANCE: ASME A112.18.1 / CSA B125.1 Standard

VS-100-PC HAND SHOWER WITH FLOW CONTROL:

CONNECTIONS: ½” NPSM Male Inlet

FLOW RATE: 2.5 gpm (9.5 L/min)

FINISH: Polished Chrome

COMPLIANCE: ASME A112.18.1 / CSA B125.1 Standard

VS-115 SUPPLY ELL:

CONNECTIONS: ½” NPT Female Inlet; ½” NPSM Male Outlet

FINISH: Polished Chrome

VS-117 IN-LINE VACUUM BREAKER:

CONNECTIONS: ½” NPSM Female Inlet; ½” NPSM Male Outlet

FINISH: Polished Chrome

COMPLIANCE: ASSE 1014 Standard

VS-120 SWIVEL CONNECTOR:

CONNECTIONS: ½” NPSM Male Inlet; ½” NPSM Female Outlet

FINISH: Polished Chrome

VS-123 30in SLIDE BAR:

FINISH: Polished Chrome

S-1554 TUB SPOUT:

CONNECTIONS: ½” NPT Female Inlet

FINISH: Polished Chrome

INSTRUCTIONS

See individual products for installation of the components and warranty information.

Summary of content (16 pages)

PAGE 1
SPEAKMAN ® SM-5450 Installation, Operation & Maintenance Instructions SENTINELPRO™ COMBINATION SERIES DESCRIPTION Speakman SentinelPro™ Combination, SM-5450, unites Anti-Scald Thermostatic / Pressure Balance Diverter Shower/Bath Valve with integral Check Stops (CPV-TP-DV), Trim with integral Volume Control / Diverter Handle (CPT-5401), Hand Shower with flow control (VS-100-PC), Supply Ell (VS-115), In-line Vacuum Breaker (VS-117), Swivel Connector (VS-120); 30in Slide Bar (VS-123), Tub Spout (S-1554), and
PAGE 2
ROUGH-IN SPEAKMAN ® 400 Anchor Mill Rd. New Castle, DE 19720 Phone: 800-537-2107 Fax: 800-977-2747 12/04/17 www.speakman.
PAGE 3
INSTRUCTIONS FOR MODELS TOOLS AND SUPPLIES CPV-TP CPV-TP-DV Pencil Keyhole Saw Adjustable Wrench 1 IMPORTANT • Be sure to read instructions thoroughly before beginning installation. Referencing the supplied rough-in dimensions (located at the end of this manual), determine the preferred location of valve. Align the supplied rough-in template with this location and trace outline of template onto wall.
PAGE 4
6 If your installation is for a shower only, apply thread seal tape to the lower outlet port and install the included cap. Wrench tighten. 7 Ensure Valve is positioned plumb and level. Remove Rough-In Template from Valve. Make threaded connections or plumb and solder all joints and fittings. Take care to protect surrounding area when soldering. Secure piping to surrounding structure. 8 OR Make piping connections for all accessories. Take care to protect surrounding area when soldering.
PAGE 5
CPV-TP / CPV-TP-DV SERVICE INSTRUCTIONS Service instructions Caution- Any repair or servicing of the valve may affect the maximum hot temperature setting of the valve. After working on the valve, make sure the maximum hot water temperature is set to the recommended setting of 110° F maximum. T/P Cartridge Removal 1) Shut off the hot & cold water supply integral stops at the valve. Remove valve trim from valve.
PAGE 6
SPEAKMAN CPV-TP ROUGH-IN DIAGRAM ® A NOTES: COMPLIANCE: ASME A112.18.1/CSA B125.1 1" 25mm HOLE FOR SHOWER ARM Shower Valve ASSE1016 6'-6" [2 METERS] TO FLOOR CONNECTIONS: 1/2" NPT MALE 1/2" SWEAT CONNECTION Hot/Cold Inlets: ½” Female Copper Sweat ½” NPT Male 5-1/2" (140MM) DIA.
PAGE 7
INSTRUCTIONS FOR MODELS CPT-5001 / CPT-5401 TOOLS AND SUPPLIES Phillips Screwdriver Silicone 1 Remove the Handle Button Screw by inserting one of the included Mounting Screws thru the hole in the Handle. Caulk Gun IMPORTANT • Do not over-tighten any connections or damage may occur. • Be sure to read instructions thoroughly before beginning installation. 2 Insert the T/P Rubber Sleeve with Tabs over Valve Bonnet. • This valve has an operating range of 20-80 psi.
PAGE 8
Ensure the Rubber Gasket is correctly installed to the Retaining Ring. Align the Retaining Ring with the slots on the Wall Plate. Press and Rotate the ring clock-wise until it Locks / Seals in place. Make sure the seal is secure with the Wall Plate. 10 Insert Handle Button into the Handle. * VIEW FROM BACK UNDERSIDE OF HANDLE If further adjustments need to be made after the Handle Button is inserted, there is an access hole at the back side of the handle. Use a paper clip to push the Button back out.
PAGE 9
SPEAKMAN CPT-5001 ROUGH-IN DIAGRAM ® A 1" 25mm HOLE FOR SHOWER ARM 7.50in 191mm 6'-6" [2 METERS] TO FLOOR 1/2" NPT MALE 1/2" SWEAT CONNECTION 1/2" NPT MALE 1/2" SWEAT CONNECTION 5-1/2" (140MM) DIA. HOLE FOR VALVE ACCESS 4.31in 110mm 1/2" NPT MALE 1/2" SWEAT CONNECTION 3.50in 89mm 3.75in 95mm 1'-9" [533mm] VALVE MOUNTING IS SHOWN FOR REFERENCE ONLY. VALVE IS NOT INCLUDED WITH CPT-5000 4’-6" [1.
PAGE 10
INSTRUCTIONS FOR MODELS TOOLS AND SUPPLIES VS-100-PC VS-100-PC-E2 VS-100-PC-E175 1 Connect the correct side of your hose (not included) to the water supply. Hand tighten. 2 Connect remaining end of Hose to inlet of Hand Shower. Hand tighten. If there are leaks at the hose connections, look into using thicker washers to ensure a tight seal. Thread Seal Tape (included) IMPORTANT Be sure to read instructions thoroughly before beginning installation.
PAGE 11
ROUGH IN DIMENSIONS 50 RUBBER TIPPED SPRAYS 31" 8 79.38 81" 2 215.90 PAUSE BUTTON 1/2-14 NPSM MALE THREADED INLET FLOW CONTROL INSERTED INTO HANDLE .714in 18.14mm ACROSS FLATS 1 3 " 16 30.18 VS-100-PC Max. Flow Rate: 2.5 gpm (9.5L/min) Min. Flow Rate: 2.0 gpm (7.6 L/min) @ 45psi FOR USE WITH AUTOMATIC COMPENSATING VALVES RATED AT 7.6 L/MIN (2.0 GPM) OR LESS. VS-100-PC-E2 Max. Flow Rate: 2.0 gpm (7.6 L/min) Min. Flow Rate: 1.5 gpm (5.
PAGE 12
SPEAKMAN COMPANY VS-115 Installation, Maintenance & Operation Instructions VERSATILE ® SUPPLY ELL DESCRIPTION VERSATILE® chrome plated brass supply ell with wall flange. SPECIFICATIONS SUPPLY INLET: ½” NPT FEMALE OUTLET: ½” NPSM MALE SHIPPING WEIGHT: 0.4 LBS. INSTALLATION Slip the wall flange on to the inlet pipe. Using teflon tape or pipe dope on threads, screw ell onto pipe and wrench tighten. Connect accessories to supply ell and firmly hand tighten. Turn water supply on and check for leaks.
PAGE 13
SPEAKMAN COMPANY VS-117 Installation, Maintenance & Operation Instructions VERSATILE ® VACUUM BREAKER DESCRIPTION VERSATILE® chrome plated brass in-line vacuum breaker. SPECIFICATIONS SUPPLY INLET: ½” NPSM FEMALE OUTLET : ½” NPSM MALE SHIPPING WEIGHT: XXX LBS. INSTALLATION Connect, using rubber washer, to supply piping. Connect accessories to vacuum breaker. Firmly hand tighten connection. Turn water supply on and check for leaks.
PAGE 14
SPEAKMAN COMPANY VS-120 Installation, Maintenance & Operation Instructions VERSATILE ® SWIVEL CONNECTOR DESCRIPTION Speakman VERSATILE® Swivel connector. SPECIFICATIONS SUPPLY INLET: ½” NPSM MALE OUTLET : ½” NPSM FEMALE SHIPPING WEIGHT: 0.1 LBS. INSTALLATION Using rubber washer(s), connect inlet to supply hose and outlet to hand held shower. Firmly hand tighten connections. Turn water supply on and check for leaks.
PAGE 15
SPEAKMAN COMPANY VS-123 Installation, Maintenance & Operation Instructions VERSATILE ® 30” SLIDE BAR DESCRIPTION Speakman VERSATILE ® 30” chrome plated slide bar with mounting screws. SPECIFICATIONS SHIPPING WEIGHT: 1.5 LBS. INSTALLATION Location of the bar is optional but restricted by the hose length. Attach bar to wall using fasteners supplied. Slip hand held shower with swivel connector onto post. Adjust height of post handle. Tighten handle to lock into place.
PAGE 16
SPEAKMAN COMPANY S-1554 Installation, Maintenance & Operation Instructions TUB SPOUT DESCRIPTION Speakman polished chrome plated metal tub spout. SPECIFICATIONS ½” NPT FEMALE INLET SHIPPING WEIGHT: XXX LBS. INSTALLATION Apply teflon tape or pipe dope to male threads and thread spout onto piping. Wrench tighten carefully. Check all connections for leaks. MAINTENANCE The gleaming finish of your SPEAKMAN tub spout can be cleaned by using mild soap and warm water.