ORIGINAL INSTRUCTION MANUAL 450W Electric Grass Trimmer N1F-GT-280/450-D Important - Please read these instructions fully before starting assembly These instructions contain important information that will help you get the best from your trimmer, ensuring it is assembled correctly and safely.
SPEAR & JACKSON SINCE 1760 For more than 250 years gardeners have enjoyed high quality performance and great results using Spear & Jackson tools. Our garden power tools combine continuous innovation and the latest in manufacturing technologies with a proud heritage. Each product is carefully designed with performance, comfort and durability firmly in mind, which has earned Spear & Jackson an enviable reputation as a maker of tools to trust.
CONTENTS Safety Information 04 Box Content / Parts 12 Assemble 13 Operate 15 Maintenance 20 Technical Data 23 Troubleshooting 25 Warranty 26 Description of symbols General safety Safety warnings Personal safetyY Operational safety Maintenance and storage safety Intended use 04 05 05 07 08 10 11 Safety guard assemble Front handle assemble Plant protector assemble Cord strain relief 13 13 13 14 General operate Height adjustment Handle adjustment Tilt adjustment Edging Automatic line feedin
SAFETY INFORMATION Please read these instructions fully before operating or maintaining your machine DESCRIPTION OF SYMBOLS The following warning symbols appear throughout this manual and indicate the appropriate safety measures you should take when operating and maintaining the grass trimmer. IMPORTANT! Please read all of the safety and operating instructions carefully before using this tool. Please pay particular attention to all sections of this user guide that carry warning symbols and notices.
SAFETY INFORMATION Please read these instructions fully before operating or maintaining your machine GENERAL SAFETY IMPORTANT! ■ Keep this instruction manual in a safe place for future reference. ■ Read the instructions carefully. Be familiar with the controls and the proper use of the equipment. ■ Never use the machine while people, especially children, or pets are nearby. Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their property.
SAFETY INFORMATION Please read these instructions fully before operating or maintaining your machine ELECTRICAL SAFETY ■ Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. ■ Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators.
SAFETY INFORMATION Please read these instructions fully before operating or maintaining your machine repaired. and clean. Properly maintained cutting tools ■ Disconnect the plug from with sharp cutting edges the power source and/ are less likely to bind and or the battery pack from are easier to control. the power tool before ■ Use the power tool, making any adjustments, changing accessories, or accessories and tool bits storing power tools. Such etc.
SAFETY INFORMATION Please read these instructions fully before operating or maintaining your machine serious personal injury. ■ Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. ■ Prevent unintentional starting.
SAFETY INFORMATION Please read these instructions fully before operating or maintaining your machine feet and hands from the cutting means. ■ Before use check the controls and proper use of the product. ■ Before using the product and after any impact, check for signs of wear or damage and repair as necessary. ■ Always disconnect the product from the power supply (i.e.
SAFETY INFORMATION Please read these instructions fully before operating or maintaining your machine ■ Disconnect from the power supply when the cord becomes damaged or tangled. ■ If the cord becomes damaged during use, disconnect the cord from the supply immediately. DO NOT TOUCH THE CORD BEFORE DISCONNECTING THE SUPPLY. ■ Do not use the product if the cord is damaged or worn. ■ Warning! The cutting elements continue to rotate after the product is switched off.
SAFETY INFORMATION Please read these instructions fully before operating or maintaining your machine similar qualified specialist. ■ When not in use, store the product out of the reach of children. ■ Have your power tools serviced by a qualified repair person using only identical replacement parts. This will ensure that safety of the power tool is maintained. manufacturer from his or her legal liability.
BOX CONTENT PARTS 1 2 3 4 5 6 7 8 10m cable Main handle On/off Switch Cable retainer Front handle Locking sleeve length adjustment Guard Plant protector 9 10 11 12 13 14 15 Tilt adjustment pedal Pole Knob Angle adjustment button Cable collector Support wheel Spare spool 2 3 11 4 15 5 1 6 13 10 12 9 8 14 7 If there are any parts missing, please call the customer helpline on 0345 605 2067 12 AFTER SALES SUPPORT 0345 605 2067
ASSEMBLE 1 Safety guard assemble i. Remove four mounting screws from motor housing. Note: They are pre-mounted on the motor housing by factory to help end-user find them quickly. And send a message to end-user, where these four screws should be used for. ii. Fit the safety guard onto the motor housing. iii. Fix the safety guard in place by using these four screws. 2 Front handle assemble i. Loosen the knob and remove it together with the bolt from the auxiliary handle. ii.
ASSEMBLE 4 Cord strain relief i. Make sure the on/off switch is in its off position. ii. Double the cord, about 3cm from the end. Lead the loop through the hole on the rear safe guard and hook the loop over the cord strain relief. Gently pull on the cord to ensure that it is firmly attached.
OPERATE General operate i. Check the product, its power cord and plug as well as accessories for damage before each use. Do not use the product if it is damaged or shows wear. ii. Double check that accessories or cutting device are properly fixed. iii. Always hold the product on its handles. Keep the handles dry to ensure safe support. Height adjustment i. Loosen the locking sleeve counter clockwise. ii. Adjust the pole length to fit your body height. iii. Tighten the locking sleeve anti-clockwise.
OPERATE Tilt adjustment Adjust the vertical angle of the trimmer head to fit the trimming conditions. i. Press the tilt adjustment pedal down with your foot. ii. Adjust the angle of the pole, up or down. iii. Release the unlock pedal and keep moving the pole until it locks in place. NOTE: Always ensure that the pedal snaps into place after adjusting the trimmer in one of the five positions! Edging 90 o i. Adjust the vertical angle of trimmer head to 0 degree by pressing the tilt adjustment pedal. ii.
OPERATE appliance. To support proper line elongation, ensure that the coil has stopped moving completely before turning on the appliance again. The lines are automatically cut to the correct length by the line cutter. Plant protector Use the plant protector to keep distance to plants like flowers, trees or other objects that could be hit by the cutting device. i. Fold the plant protector out for trimming / edging operation. ii. Fold the plant protector in for storage.
OPERATE iv. Hold the trimmer head just above the ground at an angle of approximately 30°. 30o o 30 v. Move the product slowly from side to side in a swinging motion. vi. Ensure the cutting device remains clean and free from off-cuts that may cause it to jam. Check regularly. Release the on/ off switch and disconnect the product from the power supply before checking. vii. Trim longer grass in stages; do not cut long grass in one cut. For the best results, cut longer grass in steps. viii.
OPERATE WARNING! ·· Always fit the guard before using the product ·· When cutting longer /high grass, please make sure that you cut this down in 2 to 3 stages. ·· DO NOT cut long grass in one cut, as this will damage your grass trimmer, and make your warranty invalid. Tips i. For best results, do not cut wet grass because it tends to stick to the cutting head and guard, prevents proper discharge of grass trimmings, and could cause you to slip and fall. ii.
MAINTENANCE This product does not contain any parts that can be repaired by the consumer. Contact an authorised service centre or a similarly qualified person to have it checked and repaired. Replacing the spool NOTE: Before replace the spool, make sure the mains plug is disconnected from the unit. i. Press together both locking device tabs on the spool cover and remove the cover. ii. Remove the old spool from the spool cover iii. Clean out any dirt or grass residue. iv.
MAINTENANCE i. Hold the loose ends of the line together with one hand, find the center of the line with the other hand and hook this center loop into the groove on the spool. ii. Wind the line following the directional arrows on the spool housing and hook the two ends into the side grooves. Storage i. Store the product and its accessories in a dry, frost-free place. ii. Always store the product in a place that is inaccessible to children. The ideal storage temperature is between 10°C and 30°C.
MAINTENANCE After use i. Switch the product off, disconnect it from the power supply and let it cool down. ii. Fold the plant protector in. iii. Check, clean and store the product as described below. Recycling and disposal i. Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice. ii. The product comes in a packaging that protects it against transportation damage.
TECHNICAL DATA Model Input voltage rating Input power No load speed N1F-GT-280/450-D 240V~/50Hz 450W 9000/min Trimming line Ø 1.4 mm, length 8m Cutting width 28cm Angle adjustment 0°~90° Weight 3.56kg Vibrations 4.61m/s2, K=1.
TECHNICAL DATA Measured sound pressure level LpA: 86dB(A), K=3dB(A) Measured sound power level LwA: 95.8dB(A), K=3dB(A) Guaranteed sound power level LwA: 96dB(A) The sound values have been determined according to noise test code given in EN 50636-2-91, using the basic standards EN ISO 11201 and EN ISO 3744. The sound intensity level for the operator may exceed 80dB(A) and ear protection measures are necessary.
TROUBLESHOOTING Suspected malfunctions are often due to causes that the user can fix themselves. Therefore, check the product using this section. In most cases the problem can be solved quickly.
WARRANTY If your device develops a fault, please don’t hesitate to contact our customer service department on 0345 605 2067, we can solve 80% of problems via the phone. 1. These warranty terms cover additional warranty rights and do not affect your statutory warranty rights. All our products are covered by a 3 year manufacturer warranty. 2. Claims must be accompanied by Proof of Purchase.
