Manualshelf

Brochure

ManualsBrandsSpears ManualsPVC Barbed Insert Tees6" Barbed PVC Tee (Insert x Insert x Insert)
12345678910
PVC & PP INSERT FITTINGS
FOR USE WITH POLYETHYLENE PIPE
Made in the U.S.A. 906
NOT FOR DISTRIBUTION OF COMPRESSED AIR OR GAS
Progressive Products from Spears
®
Innovation and Technology
Nominal
Size in.
Insert
Length
“P”
min.
Barb O.D. “Z”
max. min.
Barb
Depth
“V”
min.
Inside
Diameter
“D”
min.
1/2 1-1/4 .665 .635 .015 .406
3/4 1-1/4 .865 .835 .015 .562
1 1-1/4 1.095 1.065 .020 .750
1-1/4 1-1/4 1.425 1.395 .025 .995
1-1/2 1-1/2 1.665 1.630 .030 1.125
2 1-1/2 2.125 2.085 .030 1.656
2-1/2 2 2.520 2.487 .030 2.062
3 2-1/8 3.125 3.086 .030 2.600
4 3 4.090 4.044 .030 3.525
Nominal Size
in.
Average I.D.
in.
Tolerance
in.
1/2 .622 +.010 - .010
3/4 .824 +.010 - .015
1 1.049 +.010 - .020
1-1/4 1.380 +.010 - .020
1-1/2 1.610 +.015 - .020
2 2.067 +.015 - .020
2-1/2 2.469 +.015 - .025
3 3.068 +.015 - .030
4 4.026 +.015 - .035
Dimensions of Insert Ends
ASTM D 2609
Dimensions of Polyethylene Pipe
ASTM D 2104 and D 2239
STANDARDS & SPECIFICATIONS
It is the users responsibility to determine the suitability for the intended service application.
Insert Fittings Dimensions
G = (LAYING LENGTH) Intersection of center lines to insert bottom or thread bottom; 90° elbows, tees & crosses; ± 1/32 inch.
H = Intersection of center lines to end of insert or face of fi tting; 90° elbows, tees & crosses; ± 1/32 inch.
L = Overall length of fi ttings; ± 1/16 inch.
N = (LAYING LENGTH) Insert bottom to insert bottom or thread bottom; couplings & straight adapters; ± 1/16 inch.
Plastic Insert Fittings for
Polyethylene (PE) Plastic
Pipe.
• ASTM D 2609
National Sanitation Foundation (NSF
®
)
Standard 14 Plastic Fittings for
Potable Water.
Spears
®
Insert Fittings are produced from PVC
Type 1, Minimum Cell Classifi cation 12454.
CPVC Minimum Cell Classifi cation 23447.
• Material
11/16 min.
1-1/8 min.
.344 min. .55 ± .0
V
P
D
Z
Dimensions of Spiral
Barb Ends
V
DZ
P
Nominal
Size in.
Insert
Length
“P”
min.
Barb
O.D. “Z”
max.
Barb
Depth
“V”
min.
Inside
Diameter
“D”
min.
1/2 .90 .675 .055 .460
3/4 .90 .875 .055 .600
1 .96 1.105 .055 .775
Dimensions of Twist Lock Coupling