OWNER’S MANUAL
TABLE OF CONTENTS Introduction............................................................................. 4 Seat Post / Fork Compatibility......................................... 7 Accessories.............................................................................. 8 Frame Features...................................................................... 9 Frame Geometry.................................................................... 10 Shock Setup...............................................
INTRODUCTION Congratulations on your purchase and welcome to the finest line of suspension bikes available! About Off Road, Stunt, Downhill and Freeriding This manual is designed to be used in conjunction with the Bicycle Owner’s Manual and owner’s manuals supplied by the manufacturer of the front and rear suspension components. If you did not receive any of these manuals, download them from the Internet, contact your dealer, or contact us by telephone.
INTRODUCTION Here is what you should look for when you inspect your bicycle for this type of riding: bent or broken components, such as the handlebar, handlebar stem, seatpost, pedals; dents, cracks, scratches, deformation, or discoloration. Because damage may be internal and hidden, if any of these signs are present, stop riding until your bicycle has been thoroughly inspected by your Specialized dealer.
INTRODUCTION Service and Modifications Technological advances have made bicycles and bicycle components more complex, and the pace of innovation is increasing. It is impossible for this manual or the accompanying manuals to provide all of the information required to properly repair and/or maintain your bicycle. In order to help minimize the chances of an injury, it is critical for you to have work performed by an authorized Specialized retailer.
FORK SETUP INFORMATION WARNING! The FSRxc and Myka frames are compatible ONLY with single crown forks that have travel of 4.0” (100mm) or less. Use of different styled forks or forks with longer travel may result in catastrophic failure of the frame which may result in serious personal injury or death. SEAT POST SETUP SEATPOST MINIMUM INSERTION: All Specialized full suspension models with interrupted seat tubes have a small hole to identify the minimum extension allowed for your seatpost.
MUDFLAP FENDER CHAINSTAY SLEEVE The Stumpjumper Mudflap is compatible with all 0406 Stumpjumper FSR, 07 Myka and 05-07 FSRxc Models, through your local Specialized dealer. Replacement custom neoprene chainstay SlapJacket sleeves are available through your local Specialized dealer.
FSRxc / MYKA FRAME FEATURES 1. Main Frame 2. Seatstay 3. Chainstay 4. Shock Link 5. Main Pivot 6. Dropout (Horst) Pivot 7. Shock Link at Seatstay Pivot 8. Shock Link at Frame Pivot 9. Lower Shock Eyelet 10. Upper Shock Eyelet 11. Shock 12.
FSRxc / MYKA FRAME GEOMETRY FSRxc Geometry Men’s Small 1 2 3 4 5 6 7 8 *Top Tube Length **Standover Hgt Head Tube Length Head Tube Angle Seat Tube Angle BB Height Wheelbase Chainstay Length 550mm 723mm 100mm 69° 73° 321mm 1053mm 424mm (21.65“) (28.46”) (3.94”) (12.64”) (41.46”) (16.70”) Men’s Medium 586mm 745mm 110mm 69° 73° 321mm 1090mm 424mm (23.07”) (29.33”) (4.33”) (12.64”) (42.91”) (16.70”) Men’s Large 611mm 760mm 120mm 69° 73° 321mm 1116mm 424mm (24.06”) (29.92”) (4.72”) (12.64”) (43.94”) (16.
FSRxc / MYKA FRAME GEOMETRY 11
Fox Triad X-Fusion RLA / RC REAR AIR SHOCK SETUP Fig.1 Sag Setting: Set the sag (20-25% of shock stroke). See attached pressure chart for starting air pressure. Note - the chart is only a starting point, actual sag needs to the checked and adjusted on the bike, while riding, and at regular intervals. After setting the pressure, push the rubber ring up to the seal, sit on the bike gently, dismount, and measure sag. Set Standard rebound damping adjuster to rider preference.
DERAILLEUR GUARD INSTALLATION The Specialized Derailleur guard is available separately through your local Specialized dealer. The guard works with solid or Q/R axle types and is compatible with all Mountain bike models using the 2005-2006 Enduro/Demo derailleur hanger. Guard Part #: 9896-4030 Hanger Part #: 9895-4021 31 Derailleur Guard Installation (Q/R option): 1. Install rear derailleur on derailleur hanger. 2. Place rear wheel in frame and install Q/R, with springs and without Q/R end nut. 3.
NOTE: Bearing and Bolt Kits are available only through your local Specialized dealer. To retain your warranty and for your safety, all maintenance should be performed by your local Specialized dealer. Bearing Kit Parts Part # Qty. 1.a 2 1.b 4 1.c 2 1.d 2 1.e 2 1.f 6 1.g 2 1.
SBC LIMITED WARRANTY Specialized Bicycle Components, Inc.
USEFUL PRODUCT LIFE CYCLE Every Specialized bicycle and frameset has a useful product life cycle. The length of that useful product life cycle will vary with the construction and materials of the bicycle or frameset, the maintenance and care the bicycle or frameset receives over its useful product life cycle, and the type and amount of use the bicycle or frameset is subject to.
15130 Concord Circle Morgan Hill, CA 95037 www.specialized.com © 2008 Specialized Bicycles PN# W2080308 SPECIALIZED BICYCLE COMPONENTS 15130 Concord Circle, Morgan Hill, CA 95037 18 (408) 779-6229 Please note all instructions are subject to change for improvement without notice. Rev.