SPEEDZONE® PR0 CYCLOCOMPUTER Congratulations on your purchase! You are now the owner of the world’s most advanced cyclocomputer. Your Specialized SpeedZone® Pro is the first cycling computer to feature wireless digital transmitters for both speed and cadence sensing. Additionally, it incorporates a revolutionary new display screen that allows you to view five functions simultaneously. The SpeedZone® Pro has been designed to provide the best combination of performance, features, durability and ease of use.
This illustration describes the screen display and buttons: The following functions are available on your SpeedZone® Pro: • SPEED – Current Speed • AVSPD – Average speed • MXSPD – Maximum Speed • TRIP – Trip Distance • ODO – Odometer (total distance) • ATM – Automatic Start/Timer • TIMER – Stopwatch With Lap-timer • CAD – Cadence • AVCAD – Average Cadence • MXCAD – Maximum Cadence • INT – Interval Timer • DIST – Distance Countdown • ALTI – Current Altitude • ALTI – Altitude Climbed • %GRD – Inclinometer • T
coin. (See Figure 3A) If, after battery Replacing the replacement, the LCD display is blank Transmitter Battery or shows incomplete digits, turn the The Wireless Transmitter comes with computer over and press the "AC" the battery installed at the factory. button on the bottom of the case with When the battery in the transmitter the tip of a pen or a paper clip. This needs replacing, it will transmit a sigwill clear all the data and re-start the nal to your SpeedZone® Pro and the computer.
placement of the magnet is correct. (See figure 4). For the best signal reception, adjust angle of the transmitter so that it is vertical. It is not necessary, or desirable to aim the transmitter at the computer. Wheel magnets have been provided for both traditional round spokes and FIGURE 5. MAGNET bladed (flat) aerodyPLACEMENT namic spokes. For wheels with round spokes: Attach the magnet to a spoke across from the transmitter with the magnet screw.
FIGURE 7. SECURING HARDWARE FIGURE 8. FASTEN MAGNET TO CRANK ARM until the "wheel option" indicator flashes while spinning the wheel. FIGURE 9. CLEARANCE BETWEEN MAGNET AND SENSOR process that must be done only when you first install your SpeedZone® Pro and any time you replace the battery IMPORTANT INSTALLATION NOTE: in the transmitter.
vided screw. For the best signal reception, adjust angle of the transmitter so that it is vertical (See figure 7). It is not necessary, or desirable to aim the transmitter at the computer. Next, attach the cadence magnet to the inside of your crank arm directly across from the sensor. Use a tiewrap to fasten the magnet to the crank arm. (See figure 8). Do not tighten the tie-wrap until final placement of the magnet is correct.
lines the mode/side-mode sequence. Once a particular mode has been entered, its values can be reset or adjusted by pressing and holding the "SET " button for three seconds. Some operations may require that you use a combination of the "MODE" and "SET" and "TOP" buttons. 1. Setting the Display Language Your SpeedZone ® Pro can display information on the dot-matrix display area in six different languages: English (ENGL), German (GER), French (FR), Italian (ITA), Dutch (NED), and Spanish (ESP).
Km/h FIGURE 11. EASY CALIBRATION MODE 3. Setting the Programmable Odometer This mode is useful if you have replaced the battery and would like to retain the mileage you have already ridden. To access the Programmable odometer mode, first advance to the Odometer Mode by pressing "MODE" 14 button until ODO appears on the lefthand side of the screen. Note: if your display says TRIP, press the "SET" button once to change to ODO.
currently selected tire size for wheel option #1. To scroll through the preprogrammed tire sizes tap both the "MODE" and "SET" buttons simultaneously. When you reach the desired tire size press the "SET" button once to select it and enter Easy Calibration Mode for wheel option #2. Follow the same procedure to program the wheel #2 tire size and tap the "SET" button to exit Easy Calibration Mode.
three seconds. The display will now show the currently selected tire size for wheel option #1. (See figure 13). If necessary scroll through the preprogrammed tire sizes by tapping both the "MODE" and "SET" buttons simultaneously until the display shows MM and four-digit number. This number represents your tire circumference in millimeters. Press the "MODE" button until the flashing digit is correct. (Note: The "MODE" button may be held to scroll to the correct digit.
Pro will record the lap time. After the TIMER has been stopped (by pressing the "TOP" button) the previous twelve lap times can be reviewed by pressing "SET" button. Additionally, the computer will display the total time when LPTOT is shown. 7. Interval Timer (INT) Your SpeedZone® Pro is equipped with an Interval Timer. This feature allows you to customize your training by integrating a programmable repeating countdown timer into your workout.
hour and in meters when speed is measure in kilometers per hour. screen. To set the Distance Countdown, hold the "SET" button for three seconds. The hour digit will 10. Altitude ClimbedMaximum begin flashing. Press the "MODE" The Altitude Climbed function on your Button until the desired number SpeedZone® Pro calculates the total appears. (Hold down the "Mode" altitude gained during your ride. button to scroll quickly) Press the Descended altitude is not counted.
to 99.9 M/h (99.9 Km/h) with a resolution of 0.1 M/h (0.1 Km/h) Km/h FIGURE 17. MAXIMUM SPEED SCREEN Auto Start/Stop Timer (ATM)In ATM mode the timer function records the actual time spent riding. It operates only when there is speed input and is displayed In the Digital Display Area of the screen Timer Mode (TIMER)the current speed equals the Maximum In TIMER mode the stopwatch function Speed). The maximum speed is will operate when the "TOP" button is retained in memory and updated pressed.
Programmable Odometer The odometer digits are programmable. This is convenient for transferring your hard-earned mileage that is usually lost when changing batteries or computers. Km/h Km/h FIGURE 19. TRIP DISTANCE SCREEN FIGURE 20. ODOMETER SCREEN Trip Distance (DST)Trip distance mode will record up to 999.99 miles or kilometers and then roll to zero. The trip distance SET can be reset by pressing the "SET" button for three seconds. The resolution is 0.01 miles (0.01 Kilometers).
Second Wheel OptionFor riders who own more than one bicycle or who frequently change tires, the SpeedZone® Pro is capable of storing two tire sizes. You can change between the two sized by pressing both the "MODE" and "SET" buttons simultaneously for three seconds. The second wheel mode indicator will change from 1 to 2. Mileage recorded will be cumulative between the two sizes. (An accessory handlebar mount is available from your Specialized dealer. P/N 4812-4020) backlight will remain on for 3 seconds.
components come loose, it could become tangled in your spokes and cause an accident. • See your authorized Specialized dealer if you have any trouble installing or maintaining your computer. • Clean the unit with a mild detergent and a soft dry cloth. Never use any kind of solvent or alcohol. • The SpeedZone® Pro computer is intended for use on bicycles only and should not be used on any motorized vehicle. Specifications: Current Speed: 0.0 to 99.9 MPH 0.0 to 99.9 Km/H 30 Average Speed (AVS) 0.0 to 199.
date of that original purchase, this product is found to be defective in material or workmanship under normal use or service, Specialized Bicycle Components Inc. will, at its sole option, repair or replace the product without charge; provided that the Original Purchaser returns the product, securely packaged, postage prepaid to: Specialized Bicycle Components Inc., 1137 South, 3800 West Salt Lake City, UT 84104, USA. Attn: SpeedZone Pro Warranty.
