EZVR4/8 DVR SATA HDD User’s Manual Speco Technologies 200 New Highway Amityville, NY 11701 800-645-5516 www.specotech.
Safety Precautions CAUTION RISK OF ELECTRICAL SHOCK. DO NOT OPEN ! CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER (OR BACK), NO USER SERVICEABLE PARTS REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of insulated dangerous Voltage within the product’s enclosure that may be of sufficient magnitude to constitute risk of electrical shock to persons.
About this document Before installing the unit, be sure to thoroughly review and follow the instructions in this User’s Manual. Pay particular attention to the parts that are marked NOTICE. When connecting with external application, first turn the power OFF and follow manual instructions for appropriate installation. Before reading this document 1. This manual contains information for configuring, managing and using the EZVR DVR. 2.
FCC Statement: WARNING This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received including interference that may cause undesired operation." * Federal Communications Commission (FCC) Statement WARNING This Equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.
INSTALLATION 1. The package 2. Un-packed MODEL NO.: SER NO. : MADE IN TAIWA N MODEL NO.: SER NO.: MADE IN TAIWAN 3. Take the unit out from the package 4. Put on a flat desk 5. Connect your camera cables to the BNC 6. Connect your monitor cable to the BNC connectors on the rear. connector labeled “Monitor” on the rear. 7. Connect the power adaptor. 8. Turn on the “Power” switch after the cameras are installed. The EZVR will then “boot” up and begin recording.
FRONT PANEL KEYPAD Please operate the keypad function according to the DVR model that you purchased Screen mode EZVR4 : Quad screen mode button 1. 2. CHANNEL 1 : Channel 1 full screen button 3. CHANNEL 2 : Channel 2 full screen button 4. CHANNEL 3 : Channel 3 full screen button 5. CHANNEL 4 : Channel 4 full screen button Screen mode EZVR8 1. / : Split screen mode button 2. CHANNEL 1 : Channel 1 full screen button 3. CHANNEL 2 : Channel 2 full screen button 4.
Record mode EZVR4 / EZVR8 1. 24H : 24 hour recording mode 2. 72H : 72 hour recording mode 3. 240H : 240 hour recording mode 4. 480H : 480 hour recording mode 5. 960H : 960 hour recording mode 6. REC : Press this button to start recording. Press again to stop. Miscellaneous EZVR4 / EZVR8 1. MENU : Press this button to display the menu setup 2. SEARCH : Press this button to search for a specific playback time 3. BACKUP : Copies Playback video onto a USB device 4.
REAR PANEL CONNECTOR Power cord in 12VDC / 5A, Power Switch (ON / OFF) EZVR4: Camera 1 ~ 4 input BNC type EZVR8: Camera 1 ~ 8 input BNC type Main monitor output x 2 Audio channel input x 4 and output x 2 – RCA Type Alarm / Relay / RS485 connector 9
Booting Up Detecting the hard disk Live screen Indicator: Live: HDD installed Recording Overwrite Live mode Video loss Key lock Alarm Input Alarm Output Playback: Forward Reverse Pause 10
Remote controller The keys on the remote control have the same functions as the front keyboard of the unit.
Main MENU – Time Setup 1. Press ENTER to select Time Set. Press ENTER again to display the cursor. 2. Use the left or right buttons to select the item you wish to adjust, then press ENTER to change the value. 3. Press MENU to return to the previous screen and move the cursor to Apply. 4. Press ENTER to confirm. 5. Select On or Off for Daylight Savings Time. Once the time is initially set, changing the DST mode will adjust the time appropriately.
Main MENU – Audio Record Use direction buttons to select Audio Record. Press ENTER to select On or Off. Diagram Speaker RCA Cable Microphone RCA Audio Out (Line Level) RCA Audio In (Line Level) Notice: 1. Audio channel input x 4 and output x 2 2. Audio is always on input 1 when DVR is on QUAD screen of live/playback mode 3. To hear audio input 1 ~ 4, please select full screen 1 ~ 4 on live/playback mode 4.
Main MENU – Alarm Input Use direction buttons to select Alarm Input. Press the Enter button to choose the type of sensor input (Normally Open - NO or Normally Closed - NC). To disable the alarm mode switch to the Off position.. Main MENU – Alarm Output Use direction buttons to select Alarm Output. When switched to Off the alarm output is disabled. Press the Enter button to turn the output relay on or off.
Alarm Input Door closed Door open The Alarm Signal type depends upon the Alarm Sensor polarity defined as NO (Normal Open) or NC (Normal Close).
Main MENU – Auto Record Use direction buttons to select Auto Record. When Auto Record is set to On, the EZVR4/8 Press the Enter button to choose On or Off. will start recording again after 2 minutes of If switched to OFF then Auto Record is inactivity after being manually stopped. disabled. Main MENU – Overwrite HDD Use direction buttons to select Overwrite YES – Recording continues to overwrite the Enable.
Main MENU – Status Bar Use direction buttons to select Status Bar . Then press ENTER to select ON or Off . If set ON, the status bar will show date-time and status icons . If set Off the status bar will hide date-time and status icons . Main MENU – Language Use direction buttons to select Language. Press Enter button to choose a language.
Main MENU – Exit Use direction buttons to select Exit. Press Enter button to leave the menu. Playback mode – Note: Instructions appear on the screen after selecting “Search” Press SEARCH to enter the playback mode. Press ENTER to select a date and time. Use the left or right arrows to select the item Press MENU to return to the previous screen you wish to change, then press ENTER to and move cursor to Search.
Press ENTER to start the searching. Wait until the unit starts to playback. Backup mode Note: Plug in a USB device before starting the backup You must first playback an event using When the event you wish to backup appears instructions from the previous page. on the screen, press the BACKUP button to select the start time. Press the BACKUP button a second time to select the end of the copy. The unit will detect the USB drive and copy the data to the USB device.
Player Software Main Screen Please operate the player software according to the DVR model that you purchased Click icon to select the file to play. It will be in .
Starts to play; 1 2 3 4 5 6 7 8 9 10 11 12 13 1 Open File 8 Fast Forward 2 Fast Reverse 9 Capture (Save to C:\ Capture & Clipboard) 3 Play Reverse 10 Full Screen mode 4 Previous Frame 11 Quad Screen mode 5 Pause 12 Split Screen mode (Only EZVR8 included) 6 Next Frame 13 Export to AVI format 7 Play AVI Button: .vvf file export to .avi format Select export channel(s) and click audio if included.
Specifications EZVR4 EZVR8 4 CH Inputs 1.0Vp-p, 75ohm 8 CH Inputs 1.0Vp-p, 75ohm Input (BNC Type) (BNC Type) Output Main monitor composite video (BNC type) x 2 S/N Ratio More than 40dB Color 6.
85-DM4063-A004G B 24
