Flexible Intensifier® Technology Bullet IP Camera QUICK INSTALLATION GUIDE O3FB68 Please read this guide carefully before installation and operation of the product.
Notice Thank you for purchasing this product. This guide is designed to be a reference tool for the product. Please read it carefully before operating the product and retain it for future reference. Should you require any technical assistance, please contact Speco Technologies Technical Support. CAUTION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.
PRECAUTIONS Please read the manual carefully before the installation in order to set up the camera correctly and to obtain the best picture quality. Installation and services should only be carried out by an authorized personnel according to local safety regulations. If any liquid or solid matter gets into the housing, immediately disconnect the camera from power supply and have it checked by your authorized dealer before reusing. Avoid installing the camera in extremely hot or cold places.
1. PRODUCT OVERVIEW Key Features 3.0 Mega pixel 1/2.8" SONY progressive scan CMOS image sensor for excellent image quality IP68 rated water-proof Support for corridor view (in H.264) Support for corridor view (in H.264) Integrated motion detection with pre- and post-alarm image / video buffering Supports CBR (Constant Bit Rate) and VBR (Variable Bit Rate) modes Supports Tampering-Alarm Controllable frame rate Privacy Masking up to 8 areas Built-in standard PoE (802.
System Integration Physical Environment Supported Protocol Intelligent Video Alarm Trigger Firmware Upgrade Etc Memory Slot Power Source Power Consumption Net Weight Heater Dimension(mm) Operating Temperature Storage Temperature HTTPS Encryption HTTP, HTTPS, DNS, RTSP, RTP, TCP, UDP, ICMP, DHCP Motion detection 12 x 12 blocks Motion Detection, Tampering Alarm Remote Upgrade via Network 1 x Factory Reset Button Save to Micro SD card with event mode and continuous mode DC 12V / 1.
2. NAME AND FUNCTION OF EACH PART 2.
2.2 Name and Function 2 1 3 5 6 4 NO. ITEM DESCRIPTION 1 Power Connector DC12V Caution : If O3FB68 is powered by PoE, do not plug in DC Jack with active DC power into DC power connector. 2 Network and POE Connector POE (Power over Ethernet) and LAN cable 3 Lens 3.
3. INSTALLATION 3.1 How to mount to ceiling / wall Ceiling LAN Cable Power Plastic anchor x 3 (B) Bracket nut (A) L-Wrench Tapping screw (Ø4 x 30) x 3 Wall Tapping screw (Ø4 x 30) x 3 Plastic anchor x3 LAN Cable Power (A) L-Wrench (B) Bracket nut ① Drill three screw holes on the wall plate to fix three plastic anchors (supplied) in the holes. ② Fix the plastic anchors in the holes. ③ Position the bracket on the screw points. ④ Fix the bracket by tightening the screws.
3.2 3-Axis Adjustment ① Panning 360˚ Tilt 90° Slightly loosen Pan Bracket nut then adjust pan of the camera and tighten the Bracket nut. Panning 360° Bracket nut ② Tilt 90˚ Slightly loosen Tilt bolt then adjust tilt of the camera and tighten the bolt firmly. Rotating 360° ③ Rotation 360˚ Slightly loosen Tilt bolt then adjust rotation of the camera and tighten the bolt firmly. 3.3 Installation Example 3.3.
3.3.3 Accessing the Camera or video server’s Homepage 1) Open the browser and input network camera address in the address bar or double click the device in IP Scanner. Input your IP address here 2) Please input your user name and password when prompted. 3) Default user name is admin and password is 1234. 4) The first time you login to the camera camera, you will be notified that a ActiveX control is required to be installed. installed You need to allow the installation of ActiveX ActiveX.
4.
