User Manual

ManualsBrandsSpeco ManualsBullet CamerasOnSIP Indoor/Outdoor IR Bullet Network IP Camera, 2.8-12mm Lens, Dark Grey

’

Rev.1.0 (Nov., 2011)

ONSIP OB1

Summary of content (50 pages)

PAGE 1
ONSIP OB1 Owner ’s Manual ONSIP OB1 Rev.1.0 (Nov.
PAGE 2
ONSIP OB1 Owner ’s Manual Directions Be careful not to cause any physical damage by dropping or throwing ONSIP OB1. Especially keep the device out of reach from children. Do not disassemble ONSIP OB1. No After Service is assumed when disassembled. Use only the power adapter provided with ONSIP OB1. Be careful to prevent moisture or water penetration into the unit. Particular attention is needed when installing ONSIP OB1.
PAGE 3
ONSIP OB1 Owner ’s Manual Caution Any changes or modifications to this device could void the warranty. Revision History Date Revision 2011-11-01 1.0 Details First manual revision creation. Rev.1.0 (Nov.
PAGE 4
ONSIP OB1 Owner ’s Manual Contents Contents.......................................................................................... 4 1. Introduction ................................................................................ 6 1.1. Overview................................................................................................... 6 1.2. Specification .............................................................................................. 7 1.3. Applications of ONSIP OB1...............
PAGE 5
ONSIP OB1 Owner ’s Manual 6-4. Lens Setting ......................................................................................... 35 6-5. Exposure Setting .................................................................................. 36 6-6. White Balance (White Bal) Setting ........................................................ 38 6-7. WDR Setting ........................................................................................ 39 6-8. Backlight Setting ...................................
PAGE 6
ONSIP OB1 Owner ’s Manual 1. Introduction 1.1. Overview The ONSIP OB1 is multi-codec (H.264, MJPEG) IP camera (or network camera) built with embedded software and hardware technology. It enables real time transmission of synchronized video of up to D1 and audio data. Remote clients can connect to ONSIP OB1 for the real time video/audio data through various client solutions running on PC or smart device. Real time 2-way communication is available through bidirectional audio communication feature.
PAGE 7
ONSIP OB1 Owner ’s Manual 1.2. Specification Category Sub-Category Details Compression H.264 / MJPEG Resolution * Refer to the datasheet. Camera Module Mounting Gimbal 3 Axis Gimbal Audio Up 32 Kbps G.
PAGE 8
ONSIP OB1 Owner ’s Manual ID and Password protection IP filtering for restricting administrative access for audio and bi-audio Time management Sync to PC Synchronize to PC Manual Manual time setting Internet Time Server Synchronize to Time Server Active-X SDK support HTTP Source filter Rev.1.0 (Nov.
PAGE 9
ONSIP OB1 Owner ’s Manual 1.3. Applications of ONSIP OB1  Security surveillance (buildings, stores, manufacturing facilities, parking lots, banks, government facilities, military, etc.)  Remote monitoring (hospitals, kindergartens, traffic, public areas, etc.)  Teleconference (Bi-directional audio conference). Remote Learning, Internet broadcasting  Weather and environmental observation Rev.1.0 (Nov.
PAGE 10
ONSIP OB1 Owner ’s Manual 2. Product Description 2.1. Contents The product package contains followings: Contents ONSIP OB1 Power Adaptor Tools and Mounting Screws CD Quick Reference Guide Description Remarks IP camera ONSIP OB1 main unit 12VDC Adaptor Screws, L-type wrench Software & User’s Guide Quick installation guide Rev.1.0 (Nov.
PAGE 11
ONSIP OB1 Owner ’s Manual 2.2. Product Preview ONSIP OB1 IP-Installer CMS Software (NVR) PC software to view and record Weather proof PC software to allocate an IP Bullet IP Camera address to the IP Camera the A/V streaming data transmitted from IP camera. (Simultaneous support of up to 64 IP cameras) Rev.1.0 (Nov.
PAGE 12
ONSIP OB1 Owner ’s Manual 2.3. Physical description 2.3.1. External View Rear Figure 2-1. External view of ONSIP OB1 2.3.2. Connector information Power LAN Sensor-In Audio-In Audio-Out Figure 2-2. Connector information Rev.1.0 (Nov.
PAGE 13
ONSIP OB1 Owner ’s Manual Focus control OSD control Factory default Figure 2-3. Factory Default switch and Video output connector Rev.1.0 (Nov.
PAGE 14
ONSIP OB1 Owner ’s Manual 2.4. Functional Description  DC 12V: Power input for supplying 12V DC power.  MIC/LINE IN Connect external audio source or microphone.  Line Out Connect speakers with built in amplifier. Audio from remote site is output through Line out in bi-directional audio mode.  100Base-T 100Mbps Ethernet connector (RJ-45)  Alarm In/Out and Audio In Used for connecting alarm sensor, microphone and speaker to ONSIP OB1.
PAGE 15
ONSIP OB1 Owner ’s Manual Photo Coupler NO/NCType Open CollectorType Sensor1+ Sensor Device Sensor Device Sensor1- +12V GND Sensor Power Supply Sensor Power Supply Figure 2-4. SENSOR input and connection of the sensor  Factory Default Switch A switch provided for returning the IP camera to factory default state. Open the dome cover to access the switch. Press the switch for a few seconds while power is applied. Factory default Figure 2-5. Factory Default Switch Rev.1.0 (Nov.
PAGE 16
ONSIP OB1 Owner ’s Manual 2.5. Accessories for installation Figure 2-6. Accessories for installation of ONSIP OB1. Rev.1.0 (Nov.
PAGE 17
ONSIP OB1 Owner ’s Manual 3. On Site Installation Use Cables and conduits that are suitable for the installation and that are compliant to IP-67. Particular attention should be paid in the installation so that no moisture is allowed to penetrate into the unit through the cables or conduits during the life time of the product. Products of which the internal parts are exposed to moisture because of improper installation are not covered by warranty. 3.1. Bracket Figure 2-7. Bracket installation 1.
PAGE 18
ONSIP OB1 Owner ’s Manual 4. Getting Started Brief information for first time operation of ONSIP OB1 is provided in this chapter. 4.1. PC Requirement Audio/Video streaming data received from ONSIP OB1 can be displayed or stored in a PC running client programs. Minimum requirement of the PC is described below: Recommended CPU Pentium IV 3G above Main Memory 1GB above Operating System * Remark Windows XP Web Browser Internet Explorer 6.
PAGE 19
ONSIP OB1 Owner ’s Manual 4.2. Quick Installation Guide 1. Connect PC and ONSIP OB1 to network. 1) Prepare a PC to run programs for the installation and video connection (PC is needed to assign IP address to ONSIP OB1) 2) Connect ONSIP OB1 as shown in dotted line in Figure 4-1. The DC power is applied through DC adaptor. DC adaptor LAN switch Figure 4-1. Power and network connection Rev.1.0 (Nov.
PAGE 20
ONSIP OB1 Owner ’s Manual 2. Install Speco-NVR Speco-NVR is a multi-channel CMS program for to IP camera or Video server. Install Speco-NVR on remote PC to connect to these products. It is needed to assign connection information to Speco-NVR program before connection. Insert the CD provided with product into the PC and install the Speco-NVR. Admin Page Button IP installer Figure 4-2.
PAGE 21
ONSIP OB1 Owner ’s Manual 3 1 2 9 10 5 4 7 6 8 Click on the field in ③ for sorting and rearranging the list. Select network mode that best suits from the drop down list in ⑤. You can choose either Static or ADSL and Auto (DHCP), respectively. If ADSL and Auto are selected, the fields in ⑥ is deactivated. In case of ADSL, fill the User Name and Password in ⑧ with the values provided by your ISP. If DDNS service is needed, Check at the box and fill the empty field with hostname you want in ⑦. Rev.1.
PAGE 22
ONSIP OB1 Owner ’s Manual 3. Remote video connection to ONSIP OB1 1) Connection through Web Viewer Web Viewer offers simplest way of video connection to ONSIP OB1. For video connection, enter the IP address of ONSIP OB1 in the URL window of Internet Explorer as: Can be omitted the default [e.g.] Port 80 port of 80 [e.g.] Port 8080 Note: Active-X module should be installed on your PC before actual connection. If your PC is not connected to the internet, you cannot download Active-X module.
PAGE 23
ONSIP OB1 Owner ’s Manual 2) Connection through Speco-NVR Click the camera assignment button for setting camera address. Input the description, address, Ch#, User ID, Password and port and then click the save button. After assignment procedure, you must click the SAVE button. You can see the live video when you click the live view button as below. When you exit Speco-NVR, you have to input the ID/PW, admin/1234. Details for the Speco-NVR can be found in [Speco-NVR User’s Guide].
PAGE 24
ONSIP OB1 Owner ’s Manual 4. Additional settings through connection to the Admin Page All the parameters of new IP camera fallows factory default values. For more sophisticated target application it is needed to change parameters. The admin page can be connected through ”http://IP_address:HTTP_port_number”/admin.htm It is needed to enter ID and password of the administrator. Default ID and password are admin, 1234.
PAGE 25
ONSIP OB1 Owner ’s Manual 5. Trouble Shooting 5.1. No power is applied  In case of DC adaptor If PoE is not applied, the power and network connection should be made through separate cables. It is recommended to use DC adaptor supplied by provider for the feeding of the power. In case of replacing the DC power supply, make sure that the power supply meets with the power requirement of the IP camera to prevent damage or malfunction. Rev.1.0 (Nov.
PAGE 26
ONSIP OB1 Owner ’s Manual 5.2. Cannot connect to the Video Check the status of the network connection through PING test. Try the following on your PC: - Start > Run > Cmd > Ping IP address (Ex : Ping 172.16.42.51) - If “Reply from ~” message is returned ( 1 in the figure below), the network connection is in normal state. Try connection to the video again. If the problem persists, or refer to other trouble shooting notes. - If “Request timed out” message is returned.
PAGE 27
ONSIP OB1 Owner ’s Manual 5.3. Windows Vista or Windows 7 Windows Vista and Windows 7 users need to configure UAC (User Access Control) and Privilege Level for proper recording and still video capture in Speco-NVR and Web Viewer. 1. UAC (User Access Control) configuration 1) Double-click “User Accounts” in control panel 2) Double-click “Turn User Account Control on or off” 3) Uncheck “Use UAC to help protect your computer” 2.
PAGE 28
ONSIP OB1 Owner ’s Manual 1. UAC (User Access Control) configuration 1) Double-click “User Accounts” in control panel 2) Double-click “Change User Account Control setting” 3) Set to “Never notify” Rev.1.0 (Nov.
PAGE 29
ONSIP OB1 Owner ’s Manual 2. Privilege Level Control 1) Select “NVR” icon on the desktop 2) Click right mouse button and select “properties” 3) Check “Privilege Level” in “Compatibility” tab Rev.1.0 (Nov.
PAGE 30
ONSIP OB1 Owner ’s Manual 5.4. Technical Assistance If you need any technical assistance, please contact your dealer. For immediate service please provide the following information. 1. Model name 2. MAC address and Registration number 3. Purchase date 4. Description of the problem 5. Error message Rev.1.0 (Nov.
PAGE 31
ONSIP OB1 Owner ’s Manual 6. Appendix - OSD menu control To control OSD menu, there are two methods. First is Video setup page in Administration Tool using Internet Browser as below. Rev.1.0 (Nov.
PAGE 32
ONSIP OB1 Owner ’s Manual Scond is OSD menu controller on camera as below. Rev.1.0 (Nov.
PAGE 33
ONSIP OB1 Owner ’s Manual 6-1. OSD All camera functions are menu driven for easy use. 6-2. Preset Mode 1. Preset : INDOOR / OUTDOOR / LOW LIGHT / HALLWAY / LOBBY / ELEVATOR. - Used for a quick and easy setup for the installation environment. 6-3. Menu Setup 1. Press the Function Setup switch. - Main setup menu is displayed on the monitor screen. 2. Select a desired function using the Function Setup switch. - Place the cursor over a desired item. 3.
PAGE 34
ONSIP OB1 Owner ’s Manual 4. To finish the setting, select 'RETURN' and press the Function Setup switch. ☞ NOTE ■ An item with the ◀ icon also has sub menus. To select a sub menu, select an item with the icon and press the Function Setup switch. ■ An item with the - - - icon is unavailable due to function settings. Rev.1.0 (Nov.
PAGE 35
ONSIP OB1 Owner ’s Manual 6-4. Lens Setting Using this function, you can control the screen brightness. 1. When the SETUP menu screen is displayed, select 'LENS' by using the Function Setup switch so that the arrow indicates 'LENS'. 2. DC: You can adjust the minimum shutter and maximum value of ESC shutter mode. ☞ NOTE ■ If color rolling occurs when using a DC lens, set Shutter to Fixed (---). Rev.1.0 (Nov.
PAGE 36
ONSIP OB1 Owner ’s Manual 6-5. Exposure Setting 1. When the SETUP menu screen is displayed, select 'EXPOSURE' by using the Function Setup Switch. 2. Select a desired mode using the Function Setup switch. ◆ SHUTTER : You can select either auto or manual shutter. * --- : Shutter speed is fixed at 1/60sec(1/50sec) * ESC : Select this to control the shutter speed automatically. If ESC is selected, the shutter speed is automatically controlled depending on the ambient illumination of the subject.
PAGE 37
ONSIP OB1 Owner ’s Manual * LOW : Allows automatic gain control from 5.3dB to 32dB. * HIGH : Allows automatic gain control from 5.3dB to 37dB. ◆ INTENSIFY : When it is night or dark, the camera automatically detects then light level and maintains a clear picture if this mode is activated. * OFF : Deactivates the INTENSIFY function. * AUTO : Activates the INTENSIFY function. ◆ RETURN : Select this to save the changes in the EXPOSURE menu and return to the SETUP menu.
PAGE 38
ONSIP OB1 Owner ’s Manual 6-6. White Balance (White Bal) Setting Use the White Balance function to adjust the screen color. 1. When the SETUP menu screen is displayed, select 'White Bal' by using the function Setup switch so that the arrow indicates 'White Bal'. 2. Select a desired mode using the Function Setup switch. ※ Select one of the following 5 modes, as appropriate for your purpose. ◆ ATW : Select this when the color temperature is between 1,700˚K and 11,000˚K.
PAGE 39
ONSIP OB1 Owner ’s Manual 6-7. WDR Setting WDR illuminates darker spots of an image while retaining the same light level for brighter spots to even out the overall brightness of images with high contrast between bright and dark spots. 1. When the SETUP menu screen is displayed, select 'WDR' by using the switch so that the arrow indicates 'WDR'. 2. Use the switch to change the WDR level according to the contrast between bright and dark areas.9 Rev.1.0 (Nov.
PAGE 40
ONSIP OB1 Owner ’s Manual 6-8. Backlight Setting Unlike conventional cameras, the 650Line Intensifier3™ Series are designed to deliver a distinctive subject and background at the same time, even when the subject is backlight, by using the features of the proprietary W-V DSP chip. 1. When the SETUP menu screen is displayed, select 'BACKLIGHT' by using the Function Setup switch so that the arrow indicates 'BACKLIGHT'. 2. Select a desired mode using the Function Setup switch.
PAGE 41
ONSIP OB1 Owner ’s Manual ☞ NOTE ■ Because there can be a difference in the effectiveness of HLC according to the amount of light area in the screen, optimize the installation angle for the best HLC performance. ■ When dark, the HLC is only activated when a bright light exceeding a specific size in NIGHT ONLY mode. ■ The HLC is not activated in day light or when bright light is not present at night in NIGHT ONLY mode. ■ BLC Function doesn't work in the B/W mode of the DAY/NIGHT menu. Rev.1.0 (Nov.
PAGE 42
ONSIP OB1 Owner ’s Manual 6-9. SPECO DNR Setting This function reduces the background noise in a low luminance environment. 1. When the SETUP menu screen is displayed, select 'SPECO DNR' by using the Function Setup switch so that the arrow indicates 'SPECO DNR'. 2. Select a desired mode using the Function Setup switch. ◆ OFF : Deactivates SPECO DNR. Noise is not reduced. ◆ ON : Activates SPECO DNR so that noise is reduced. 3. Set the SPECO DNR mode to 'ON' and press the Function Setup switch.
PAGE 43
ONSIP OB1 Owner ’s Manual 6-10. Day/Night Setting You can display pictures in color or black and white. 1. When the SETUP menu screen is displayed, select 'DAY/NIGHT'by using the Function Setup switch so that the arrow indicates 'DAY/NIGHT'. 2. Select a desired mode using the Function Setup Switch according to the picture display you want. ◆ COLOR : The picture is always displayed in color. ◆ B/W : The picture is always displayed in black and white.
PAGE 44
ONSIP OB1 Owner ’s Manual - BURST MODE : You can turn on or off the burst signal on B/W mode. - DURATION : You can select brightness of illumination about changing the day/night mode. - DWELLTIME : You can select the duration time about changing the day/night mode. →3s, 5s, 7s, 10s, 15s, 20s, 30s, 40, 60s * The day/night switching point of the camera can be adjusted. ☞ NOTE ■ When AGC in the EXPOSURE menu is 'OFF', '---' mode operates as like selecting 'COLOR' mode and 'AUTO' mode can not be selected.
PAGE 45
ONSIP OB1 Owner ’s Manual 6-11. Special Setting 1. When the SETUP menu screen is displayed, select 'SPECIAL' by using the Function Setup switch so that the arrow indicates 'SPECIAL'. 2. Select a desired mode using the Function Setup switch. Rev.1.0 (Nov.
PAGE 46
ONSIP OB1 Owner ’s Manual ◆ IMAGE ADJ. : 1) When the SETUP menu screen is displayed, select 'IMAGE ADJ' by using the Function Setup switch so that the arrow indicates 'IMAGE ADJ'. 2) Select a desired mode using the Function Setup switch. * V-REV : You can flip the picture vertically on the screen. * H-REV : You can flip the picture horizontally on the screen. * D-ZOOM : You can use a digital zoom of x1 ~ x16.
PAGE 47
ONSIP OB1 Owner ’s Manual ◆ CAM TITLE: If you enter a title, the title will appear on the monitor. 1) If the SPECIAL menu screen is displayed, use the Function Setup switch so that the arrow indicates 'CAM TITLE'. 2) Set it to 'ON' by using the Function Setup switch. 3) Press the Function Setup switch. 4) Use the Function Setup switch to move to a desired letter and select the letter by pressing the Function Setup switch. Repeat this to enter multiple letters. You can enter up to 15 letters.
PAGE 48
ONSIP OB1 Owner ’s Manual ☞ NOTE ■ When the CAM TITLE menu is ‘OFF’, no title will be displayed on the monitor screen even if you enter one. ■ Only English is available in this mode. ■ If you move the cursor to CLR and press the Function Setup switch, all the letters are deleted. To edit a letter, change the cursor to the bottom left arrow and press the Function Setup switch. Move the cursor over the letter to be edited, move the cursor to the letter to be inserted and then press the Function Setup switch.
PAGE 49
ONSIP OB1 Owner ’s Manual indicates ‘MOTION DET’. 2) Set up the mode using the Function Setup switch. - SENSITIVITY: You can select up to 8 MD areas. When SENSITIVITY number is high, motion detection sensitivity is increased to recognize even small movement. - AREA MODE: Determines whether to use the MD area selected in SENSITIVITY. - SEL POS: Determines which of the 4 vertices of each MD area is to be used. - XPOS: Determines the coordinate of the horizontal axis for SEL POS.
PAGE 50
ONSIP OB1 Owner ’s Manual 6-12. RETURN Setting Select a desired RETURN mode using the Function Setup Switch. - SAVE: Save the current settings and RETURN the MAIN SETUP menu. - NOT SAVE: Do not save the current settings and RETURN the MAIN SETUP menu. - RESET: Resets the camera settings to the factory defaults. Language, Communication and Monitor Settings are not initialized. Rev.1.0 (Nov.