User Manual

ManualsBrandsSpeco ManualsCamera & PhotoOnSIP IP Indoor Dome Camera, 4.3mm Lens, White Housing

’

Rev.1.0(Nov., 2011)

ONSIP OD8

Summary of content (29 pages)

PAGE 1
ONSIP OD8 Owner ’s Manual ONSIP OD8 Rev.1.0(Nov.
PAGE 2
ONSIP OD8 Owner ’s Manual Directions Be careful not to cause any physical damage by dropping or throwing ONSIP OD8. Especially keep the device out of reach from children. Do not disassemble ONSIP OD8. No After Service is assumed when disassembled. Use only the power adapter provided with ONSIP OD8. Be careful to prevent moisture or water penetration into the unit. Particular attention is needed when installing ONSIP OD8.
PAGE 3
ONSIP OD8 Owner ’s Manual Caution Any changes or modifications to this device could void the warranty. Revision History Date Revision 2011-11-01 1.0 Details First manual revision creation. Rev.1.0(Nov.
PAGE 4
ONSIP OD8 Owner ’s Manual Contents Contents ........................................................................................... 4 1. Introduction ................................................................................... 5 1.1. Overview................................................................................................... 5 1.2. Specification .............................................................................................. 6 1.3. Applications of ONSIP OD8 ........
PAGE 5
ONSIP OD8 Owner ’s Manual 1. Introduction 1.1. Overview The ONSIP OD8 is a state-of-the-art (D1), multi-codec (H.264, MJPEG) IP camera (or network camera) built with embedded software and hardware technology. It enables real time transmission of synchronized video of up to D1 pixels and audio data. Remote clients can connect to ONSIP OD8 for the real time video/audio data through various client solutions running on PC, PDA or mobile phones.
PAGE 6
ONSIP OD8 Owner ’s Manual 1.2. Specification Category Video Sub-Category Details Compression H.264/MJPEG Resolution **Refer to the datasheet. Audio Up 32 Kbps G.726 (Bi-directional) Down 64 Kbps PCM Interface RJ-45, 10/100 Mbps, PoE (802.3af) Access network Static, DHCP, PPP/PPPoE Protocol IPv4/6, TCP, UDP, IGMP, ICMP, ICMPv6 etc.
PAGE 7
ONSIP OD8 Owner ’s Manual Sync to PC Synchronize to PC Manual Manual time setting Internet Time Server Synchronize to Time Server DLS Day light saving Time management Active-X SDK support HTTP Rev.1.0(Nov.
PAGE 8
ONSIP OD8 Owner ’s Manual 1.3. Applications of ONSIP OD8  Security surveillance (buildings, stores, manufacturing facilities, parking lots, banks, government facilities, military, etc.)  Remote monitoring (hospitals, kindergartens, traffic, public areas, etc.)  Teleconference (Bi-directional audio conference). Remote Learning, Internet broadcasting  Weather and environmental observation Rev.1.0(Nov.
PAGE 9
ONSIP OD8 Owner ’s Manual 2. Product Description 2.1. Contents The product package contains followings: Contents ONSIP OD8 Power Adaptor Mounting bracket CD Quick Reference Guide Description Remarks IP camera ONSIP OD8 main unit Default built in standard PoE module (IEEE802.3af) Standard ceiling mount bracket Embedded (Optional item) Software & User’s Guide Quick installation guide Rev.1.0(Nov.
PAGE 10
ONSIP OD8 Owner ’s Manual 2.2. Product Preview 2.2.1. Preview ONSIP OD8 IP-Installer CMS Software (Speco-NVR) PC software to view and record IP Camera PC software to allocate an IP address to the IP Camera the A/V streaming data transmitted from IP camera. (Simultaneous support of up to 64 IP cameras) Rev.1.0(Nov.
PAGE 11
ONSIP OD8 Owner ’s Manual 2.3. Physical description 2.3.1. External View Figure 2-1. External view of ONSIP OD8 2.3.2. Rear panel Serial (pin 1 Mic/Line In Line Out LAN at leftmost) Figure 2-2. Rear panel of ONSIP OD8 Rev.1.0(Nov.
PAGE 12
ONSIP OD8 Owner ’s Manual 2.4. Functional Description  MIC/LINE IN Connect external audio source or microphone.  Line Out Connect speakers with built in amplifier. Audio from remote site is output through Line out in bi-directional audio mode.  100Base-T 100Mbps Ethernet connector (RJ-45) with PoE standard (802.3af). 2 LEDs on the Ethernet connector shows the status of ONSIP OD8 as the followings: - Status LED (Dual Color - Red/Green): It will be lit in green or red depending on the status.
PAGE 13
ONSIP OD8 Owner ’s Manual  RS-232C 3 Pins on the right of the connector are assigned for RS-232 port. Please note that left most pin is numbered as 1. Pin Description 1 Not used 2 Not used 3 RxD (Connect to TxD of the other end) 4 TxD (RxD (Connect to RxD of the other end)) 5 Ground of RS-232C Misc. For debugging & factory use only.  Factory Default Switch A switch provided for returning the IP camera to factory default state. Open the dome cover to access the switch.
PAGE 14
ONSIP OD8 Owner ’s Manual 3. On Site Installation 3.1. Ceiling or Wall Mounting Please follow through the procedures in the order of the numbers for each procedure. Mounting Knob Holes 1. Fix the mounting bracket. Mounting Bracket 2. Seat the IP camera onto the mounting Mounting Knobs bracket. Make sure to align the angular positions of the “mounting knobs” and mating “mounting bracket holes” properly. Once seated, rotate the camera to the right until it is locked. 3.
PAGE 15
ONSIP OD8 Owner ’s Manual 3.2. Embedded mount bracket Please follow through the procedures in the order of the numbers for each procedure. 2. Place the bracket holder above the ceiling Bracket Holder panel through prepared hole. Ceiling Panel 1. Prepare a 165mm diameter hole on the Recessed Mounting Bracket 3. Plug in the recessed mounting bracket Fixing Screws ceiling through the hole. 4. Fix the mounting bracket and bracket holder using two screws. 5.
PAGE 16
ONSIP OD8 Owner ’s Manual Mounting Knob Holes Mounting Knobs Make sure to align the positions of the “mounting knobs” and “mounting knob holes” when you plug in the IP camera into the mounting bracket. Once it is firmly plugged in, twist the IP camera to the right until it is locked. Rev.1.0(Nov.
PAGE 17
ONSIP OD8 Owner ’s Manual 4. Getting Started Brief information for first time operation of ONSIP OD8 is provided in this chapter. 4.1. PC Requirement Audio/Video streaming data received from ONSIP OD8 can be displayed or stored in a PC running client programs. Minimum requirement of the PC is described below: Recommended CPU Pentium IV 3G above Main Memory 1GB above Operating System * Remark Windows XP Web Browser Internet Explorer 6.
PAGE 18
ONSIP OD8 Owner ’s Manual 4.2. Quick Installation Guide 1. Connect PC and ONSIP OD8 to network. 1) Prepare a PC to run programs for the installation and video connection (PC is needed to assign IP address to ONSIP OD8) 2) In case of using PoE, connect the PC and ONSIP OD8 to the network using one of the following ways. If your LAN Switch does not support standard PoE, connect ONSIP OD8 as shown in dotted line in Figure 4-1. The DC power is applied through DC adaptor.
PAGE 19
ONSIP OD8 Owner ’s Manual 2. Install Speco-NVR Speco-NVR is a multi-channel CMS program for to IP camera or Video server. Install Speco-NVR on remote PC to connect to these products. It is needed to assign connection information to Speco-NVR program before connection. Insert the CD provided with product into the PC and install the Speco-NVR. Admin Page Button IP installer Figure 4-2.
PAGE 20
ONSIP OD8 Owner ’s Manual 3 1 2 9 10 5 4 7 6 8 Click on the field in ③ for sorting and rearranging the list. Select network mode that best suits from the drop down list in ⑤. You can choose either Static or ADSL and Auto (DHCP), respectively. If ADSL and Auto are selected, the fields in ⑥ is deactivated. In case of ADSL, fill the User Name and Password in ⑧ with the values provided by your ISP. i) If DDNS service is needed, Check at the box and fill the empty field with hostname you want in ⑦.
PAGE 21
ONSIP OD8 Owner ’s Manual 3. Remote video connection to ONSIP OD8 1) Connection through Web Viewer Web Viewer offers simplest way of video connection to ONSIP OD8. For video connection, enter the IP address of ONSIP OD8 in the URL window of Internet Explorer as : Can be omitted the [e.g.] Port 80 default port of 80 [e.g.] Port 8080 Note : Active-X module should be installed on your PC before actual connection. If your PC is not connected to the internet, you cannot download Active-X module.
PAGE 22
ONSIP OD8 Owner ’s Manual 2) Connection through Speco-NVR Click the camera assignment button for setting camera address. Input the description, address, Ch#, User ID, Password and port and then click the save button. After assignment procedure, you must click the SAVE button. You can see the live video when you click the live view button as below. When you exit Speco-NVR, you have to input the ID/PW, admin/1234. Details for the Speco-NVR can be found in [Speco-NVR User’s Guide].
PAGE 23
ONSIP OD8 Owner ’s Manual 4. Additional settings through connection to the Admin Page All the parameters of new IP camera follows factory default values. For more sophisticated target application it is needed to change parameters. The admin page can be connected through ”http://IP_address:HTTP_port_number”/admin.htm It is needed to enter ID and password of the administrator. Default ID and password are root, admin.
PAGE 24
ONSIP OD8 Owner ’s Manual 5. Trouble Shooting 5.1. No power is applied  In case of Standard PoE (Power over Ethernet) Power supply through standard PoE is possible only when the following conditions are met. 1. Standard PoE is supported on the product. 2. The LAN switch supports standard PoE. Make sure that both the IP camera and the LAN switch support standard PoE (IEEE 802.3af)  In case of DC adaptor If PoE is not applied, the power and network connection should be made through separate cables.
PAGE 25
ONSIP OD8 Owner ’s Manual 5.2. Cannot connect to the Video Check the status of the network connection through PING test. Try the following on your PC : - Start > Run > Cmd > Ping IP address (Ex : Ping 172.16.42.51) - If “Reply from ~” message is returned ( 1 in the figure below), the network connection is in normal state. Try connection to the video again. If the problem persists, or refer to other trouble shooting notes. - If “Request timed out” message is returned.
PAGE 26
ONSIP OD8 Owner ’s Manual 5.3. Windows Vista or Windows 7 Windows Vista and Windows 7 users need to configure UAC (User Access Control) and Privilege Level for proper recording and still video capture in Speco-NVR and Web Viewer. 1. UAC (User Access Control) configuration 1) Double-click “User Accounts” in control panel 2) Double-click “Turn User Account Control on or off” 3) Uncheck “Use UAC to help protect your computer” 2.
PAGE 27
ONSIP OD8 Owner ’s Manual 1. UAC (User Access Control) configuration 1) Double-click “User Accounts” in control panel 2) Double-click “Change User Account Control setting” 3) Set to “Never notify” Rev.1.0(Nov.
PAGE 28
ONSIP OD8 Owner ’s Manual 2. Privilege Level Control 1) Select “NVR” icon on the desktop 2) Click right mouse button and select “properties” 3) Check “Privilege Level” in “Compatibility” tab Rev.1.0(Nov.
PAGE 29
ONSIP OD8 Owner ’s Manual 5.4. Technical Assistance If you need any technical assistance, please contact your dealer. For immediate service please provide the following information. 1. Model name 2. MAC address and Registration number 3. Purchase date 4. Description of the problem 5. Error message Rev.1.0(Nov.