User Manual

ManualsBrandsSpeco ManualsNetworkOnSIP IP Indoor Turret Camera, 4.3mm Lens

’

Rev.1.2 (Oct. 2012)

OIPC21T7B

Owner’s Manual

Summary of content (29 pages)

PAGE 1
OIPC21T7B Owner ’s Manual Owner’s Manual OIPC21T7B Rev.1.2 (Oct.
PAGE 2
OIPC21T7B Owner ’s Manual Directions Be careful not to cause any physical damage by dropping or throwing OIPC21T7B. Especially keep the device out of reach from children. Do not disassemble OIPC21T7B. No After Service is assumed when disassembled. Use only the power adapter provided with OIPC21T7B. Be careful to prevent moisture or water penetration into the unit. Particular attention is needed when installing OIPC21T7B.
PAGE 3
OIPC21T7B Owner ’s Manual Caution Any changes or modifications in construction of this device which are not explicitly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Revision History Date Revision 2012-09-01 1.0 Details First manual revision creation. Rev.1.2 (Oct.
PAGE 4
OIPC21T7B Owner ’s Manual Contents Contents ............................................................................................................ 4 1. Introduction................................................................................................... 6 1.1. Overview .................................................................................................................... 6 1.2. Specification ......................................................................................
PAGE 5
OIPC21T7B Owner ’s Manual 5.2. Cannot connect to the Video .......................................... Error! Bookmark not defined. 5.3. Windows Vista or Windows 7 ......................................... Error! Bookmark not defined. 5.4. Technical Assistance ...................................................... Error! Bookmark not defined. Rev.1.2 (Oct.
PAGE 6
OIPC21T7B Owner ’s Manual 1. Introduction 1.1. Overview The OIPC21T7B is a state-of-the-art, multi-codec (H.264, MJPEG) IP camera (or network camera) built with embedded software and hardware technology. It enables real time transmission of synchronized video of up to D1 and audio data. Remote clients can connect to OIPC21T7B for the real time video data through various client solutions running on PC or mobile phones. Rev.1.2 (Oct.
PAGE 7
OIPC21T7B Owner ’s Manual 1.2. Specification Category Video Sub-Category Details Compression H.264/MJPEG Resolution **Refer to the datasheet. Audio Up N/A (Bi-directional) Down N/A Interface RJ-45, 10/100 Mbps Access network Static, DHCP, PPP/PPPoE Protocol IPv4/6, TCP, UDP, IGMP, ICMP, ICMPv6 etc.
PAGE 8
OIPC21T7B Owner ’s Manual Manual Manual time setting Internet Time Server Synchronize to Time Server DLS Day light saving Active-X SDK support HTTP Source filter Rev.1.2 (Oct.
PAGE 9
OIPC21T7B Owner ’s Manual 1.3. Applications of OIPC21T7B  Security surveillance (buildings, stores, manufacturing facilities, parking lots, banks, government facilities, military, etc.)  Remote monitoring (hospitals, kindergartens, traffic, public areas, etc.)  Teleconference (Bi-directional audio conference). Remote Learning, Internet broadcasting  Weather and environmental observation Rev.1.2 (Oct.
PAGE 10
OIPC21T7B Owner ’s Manual 2. Product Description 2.1. Contents The product package contains followings : Contents OIPC21T7B Power Adaptor CD Quick Reference Guide Description Remarks IP camera OIPC21T7B main unit 12VDC Adaptor Optional item Software & User’s Guide Quick installation guide Rev.1.2 (Oct.
PAGE 11
OIPC21T7B Owner ’s Manual 2.2. Product Preview 2.2.1. Preview OIPC21T7B IP-Installer CMS Software (Speco-NVR) PC software to view and record IP Camera PC software to allocate an IP address to the IP Camera the A/V streaming data transmitted from IP camera. (Simultaneous support of up to 64 IP cameras) Rev.1.2 (Oct.
PAGE 12
OIPC21T7B Owner ’s Manual 2.3. Physical description 2.3.1. External View Figure 2-1. External view of OIPC21T7B 2.4. Functional Description  DC 12V : Power input for supplying 12V DC power.  Line Out Connect speakers with built in amplifier. Audio from remote site is output through Line out in bi-directional audio mode.  100Base-T 100Mbps Ethernet connector (RJ-45).
PAGE 13
OIPC21T7B Owner ’s Manual - LINK/LAN LED (Orange) It will be lit with orange color when network cabling is all right. Blinking orange color indicates that normal data transmission is under way. Off state indicates that there is trouble in network connection.  ALARM IN/OUT and Composite Video Output Figure 2-3 ALARM IN/OUT and Composite Video Output Terminal of OIPC21T7B Used for connecting P/T device, sensor, and composite video output. Pin assignments are as follows.
PAGE 14
OIPC21T7B Owner ’s Manual Photo Coupler NO/ NCType Open CollectorType Sensor1+ Sensor Device Sensor Device Sensor1- +12V GND Sensor Power Supply Sensor Power Supply Figure 2-4. SENSOR Input connection  Factory Default Switch A switch provided for returning the IP camera to factory default state. Open the cover to access the switch. Press the switch for a few seconds while power is applied.
PAGE 15
OIPC21T7B Owner ’s Manual 3. On Site Installation 3.1. Ceiling or Wall Mounting Please follow through the procedures in the order of the numbers for each procedure. 1. Open dome cover as following. 2. Fix the product using 3 screws and anchors Rev.1.2 (Oct.
PAGE 16
OIPC21T7B Owner ’s Manual 3. Combine dome cover. Rev.1.2 (Oct.
PAGE 17
OIPC21T7B Owner ’s Manual 4. Getting Started Brief information for first time operation of OIPC21T7B is provided in this chapter. 4.1. PC Requirement Audio/Video streaming data received from OIPC21T7B can be displayed or stored in a PC running client programs. Minimum requirement of the PC is described below: Recommended CPU Dual Core 3Ghz 3G above Main Memory 2GB above Operating System * Remark Windows XP Web Browser Internet Explorer 8.
PAGE 18
OIPC21T7B Owner ’s Manual 4.2. Quick Installation Guide 1. Connect PC and OIPC21T7B to network. 1) Prepare a PC to run programs for the installation and video connection (PC is needed to assign IP address to OIPC21T7B) 2) OIPC21T7B as shown in dotted line in Figure 4-1. The DC power is applied through DC adaptor. DC adaptor LAN switch Figure 4-1. Power and network connection Install “IP installer and set IP parameters on OIPC21T7B Insert the CD provided with product into the PC.
PAGE 19
OIPC21T7B Owner ’s Manual 2. Install Speco-NVR Speco-NVR is a multi-channel CMS program for to IP camera or Video server. Install Speco-NVR on remote PC to connect to these products. It is needed to assign connection information to Speco-NVR program before connection. Insert the CD provided with product into the PC and install the Speco-NVR. Admin Page Button IP installer Figure 4-2.
PAGE 20
OIPC21T7B Owner ’s Manual 3 1 2 9 10 5 4 7 6 8 Click on the field in ③ for sorting and rearranging the list. Select network mode that best suits from the drop down list in ⑤. You can choose either Static or ADSL and Auto (DHCP), respectively. If ADSL and Auto are selected, the fields in ⑥ is deactivated. In case of ADSL, fill the User Name and Password in ⑧ with the values provided by your ISP. If DDNS service is needed, Check at the box and fill the empty field with hostname you want in ⑦. Rev.1.
PAGE 21
OIPC21T7B Owner ’s Manual 3. Remote video connection to ONSIP O2D3 1) Connection through Web Viewer Web Viewer offers simplest way of video connection to ONSIP O2D3 . For video connection, enter the IP address of ONSIP O2D3 in the URL window of Internet Explorer as: Can be omitted the [e.g.] Port 80 default port of 80 [e.g.] Port 8080 Note : Active-X module should be installed on your PC before actual connection. If your PC is not connected to the internet, you cannot download Active-X module.
PAGE 22
OIPC21T7B Owner ’s Manual 2) Connection through Speco-NVR Click the camera assignment button for setting camera address. Input the description, address, Ch#, User ID, Password and port and then click the save button. After assignment procedure, you must click the SAVE button. You can see the live video when you click the live view button as below. When you exit Speco-NVR, you have to input the ID/PW, admin/1234. Details for the Speco-NVR can be found in [Speco-NVR User’s Guide].
PAGE 23
OIPC21T7B Owner ’s Manual 4. Additional settings through connection to the Admin Page All the parameters of new IP camera follows factory default values. For more sophisticated target application it is needed to change parameters. The admin page can be connected through ”http://IP_address:HTTP_port_number”/admin.htm It is needed to enter ID and password of the administrator. Default ID and password are admin, 1234.
PAGE 24
OIPC21T7B Owner ’s Manual 5. Trouble Shooting 5.1. No power is applied  In case of DC adaptor If PoE is not applied, the power and network connection should be made through separate cables. It is recommended to use DC adaptor supplied by provider for the feeding of the power. In case of replacing the DC power supply, make sure that the power supply meets with the power requirement of the IP camera to prevent damage or malfunction. Rev.1.2 (Oct.
PAGE 25
OIPC21T7B Owner ’s Manual 5.2. Cannot connect to the Video Check the status of the network connection through PING test. Try the following on your PC : - Start > Run > Cmd > Ping IP address (Ex : Ping 172.16.42.51) - If “Reply from ~” message is returned ( 1 in the figure below), the network connection is in normal state. Try connection to the video again. If the problem persists, or refer to other trouble shooting notes. - If “Request timed out” message is returned.
PAGE 26
OIPC21T7B Owner ’s Manual 5.3. Windows Vista or Windows 7 Windows Vista and Windows 7 users need to configure UAC (User Access Control) and Privilege Level for proper recording and still video capture in Speco-NVR and Web Viewer. 1. UAC (User Access Control) configuration 1) Double-click “User Accounts” in control panel 2) Double-click “Turn User Account Control on or off” 3) Uncheck “Use UAC to help protect your computer” 2.
PAGE 27
OIPC21T7B Owner ’s Manual 1. UAC (User Access Control) configuration 1) Double-click “User Accounts” in control panel 2) Double-click “Change User Account Control setting” 3) Set to “Never notify” Rev.1.2 (Oct.
PAGE 28
OIPC21T7B Owner ’s Manual 2. Privilege Level Control 1) Select “NVR” icon on the desktop 2) Click right mouse button and select “properties” 3) Check “Privilege Level” in “Compatibility” tab Rev.1.2 (Oct.
PAGE 29
OIPC21T7B Owner ’s Manual 5.4. Technical Assistance If you need any technical assistance, please contact your dealer. For immediate service please provide the following information. 1. Model name 2. MAC address and Registration number 3. Purchase date 4. Description of the problem 5. Error message Rev.1.2 (Oct.