Product Manual

Rod Mounted
Set up the laser to the desired grade.
Attach the CR700 to the grade rod clamp.
Attach the assembly to a grade rod.
Adjust deadband (accuracy) and volume as
desired.
Place the grade rod on a height benchmark
or to desired grade.
Adjust the grade rod to “on grade” (green light).
While checking other locations, the LED arrows indicate high or low while
the LCD provide digital distance from grade.
www.spectralasers.com
CR700
Combination Receiver
Machine Mount / Rod Mount
User Guide
Specications
Machine Mounted
Set up the laser to the desired grade. The laser
should be within 200m (660 ft) of the machine.
Plumb the dipper stick. Position the bucket on
height benchmark, or at correct depth.
Attach the CR700 to the C71 magnet clamp.
Adjust deadband to desired accuracy (5, 10 or
25mm).
Attach CR700 assembly to the dipper stick. Adjust height to be on grade
(green lights).
While digging, bring dipper stick to plumb position and lower to dirt depth to
determine height from desired grade.
Notice to Our European Union Customers
For product recycling instructions and more information,
please go to: www.trimble.com/environment/summary.html
Recycling in Europe
To recycle Trimble WEEE,
call: [phone], and
ask for the “WEEE associate,” or
Mail a request for recycling instructions to:
Trimble Europe BV c/o Menlo Worldwide Logistics
Meerheide 45 5521 DZ Eersel, NL
Trimble - Precision Tools
5475 Kellenburger Road
Dayton, Ohio 45424-1099
U.S.A.
[phone] Phone
Toll Free USA 1-888-527-3771
www.spectralasers.com
© 2019, Trimble Inc., All rights reserved.
Reorder PN 1278-0100 Rev A (EN) (01/19)
Trimble warrants the CR700 to be free of defects in material and workmanship
for a period of three years. Trimble or its authorized service center will repair
or replace, at its option, any defective part, or the entire product, for which
notice has been given during the warranty period. If required, travel and per
diem expenses to and from the place where repairs are made will be charged
to the customer at the prevailing rates. Customers should send the product
to Trimble or the nearest authorized service center for warranty repairs
or exchange, freight prepaid. Any evidence of negligent, abnormal use,
accident, or any attempt to repair the product by other than factory-authorized
personnel using Trimble certied or recommended parts, automatically voids
the warranty. The foregoing states the entire liability of Trimble regarding the
purchase and use of its equipment. Trimble will not be held responsible for
any consequential loss or damage of any kind. This warranty is in lieu of all
other warranties, except as set forth above, including any implied warranty
merchantability of tness for a particular purpose, are hereby disclaimed. This
warranty is in lieu of all other warranties, expressed or implied.
Warranty
EMC Declaration of Conformity
This receiver has been tested and found to comply with the limits for a Class B digital
device for radio noise for digital apparatus set out in the Radio Interference Regulations
of the Canadian Department of Communication, and is pursuant to part 15 of the Federal
Communication Commission (FCC) rules. These limits are designed to provide reason-
able protection against harmful interference in a residential installation. This receiver
generates radio frequency. If it’s not used in accordance with the instructions, it may
cause harmful interference to radio or television reception. Such interference can be
determined by turning the receiver off and on. You are encouraged to try eliminating the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the laser and the receiver.
For more information, consult your dealer or an experience
radio/television technician.
CAUTION: Changes or modications to the receiver that are not expressly approved by
Trimble could void authority to use the equipment.
Declaration of Conformity
Application of Council Directive(s): 89/336/EEC
Manufacturer’s Name: Trimble Inc.
Manufacturer’s Address: 5475 Kellenburger Road
Dayton, Ohio 45424-1099 U.S.A.
European Representative Address: Trimble GmbH Am Prime Parc 11
65479 Raunheim, Germany
Model Number: CR700
Conformance to Directive(s): EC Directive 89/336/EEC using
EN55022 and EN50082-1
Equipment Type/Environment: ITE/residential, commercial
& light industrial
Product Standards: Product meets the limit B and
methods of EN55022
Product meets the levels and
methods of IEC 801-2, 8 kV air,
4 kV contact IEC 801-3, 3 V/m
26 to 1000 MHz 80%, @ 1 kHz
Working Radius: 1 m - 460 m (3 ft - 1500 ft)
(Laser dependent):
Laser Detection Height: 127.0 mm (5“)
Numeric Readout Height: 102.0 mm (4“)
Internal Radio: Full 2-way communication, operation
and security lock with paired device
Radio Working Radius: Up to 200 m (660 ft), depending on
orientation, conditions and paired device
Accuracy (Deadband):
Ultra Fine 0.5 mm 0.02 in 1/32 in
Super Fine 1.0 mm 0.05 in 1/16 in
Fine 2.0 mm 0.10 in 1/8 in
Medium 5.0 mm 0.20 in 1/4 in
Coarse 10.0 mm 0.50 in 1/2 in
Machine 25.0 mm 1.00 in 1 in
Reception Angle: 200° (laser and distance dependent)
Strobe Anti-strobe sensor
Detectable Spectrum: 610 nm ... 780 nm
Beeper Volumes: Loud = 110 dBA
Medium = 95 dBA, Low = 65 dBA
LED Grade Indicators: Green on-grade, Red Hi, Blue Low
Brightness: Off, Bright, Super-Bright
Power Supply: 3 x 1.5 Volt “AA” batteries
Battery Life: 60+ hours; 16 continuous backlight
Automatic Shut Off: 30 minutes
Environmental: Waterproof, Dustproof to IP67
Weight without clamp: 471 g (16.6 oz.)
Dimensions w/o clamp 98 x 200 x 37 mm
(3.9” x 7.8” x 1.5”)
Operating Temperature: -20°C...+60°C (-4°F... +140°F)
Storage Temperature: -40°C...+70°C (-40°F...+158°F)
Regulatory CE EMC / RoHS Compliant
*Specifications subject to change without notice.
Vertical Mounted
Set up the laser in vertical mode.
Consider setting CR700 to Drift Alarm (see menu) to enable warning if the
laser is disturbed.
Consider using Planlok to set laser direction. With Planlok, the laser will nd
the CR700. Must use a laser that can be paired with CR700.
CR700 can be placed directly on a oor in a building. Vertical adapter
105516 (sold separately) may be useful to attach to a batter board or tripod.
Attach Clamp
Attach the CR700 to the
C71 magnet clamp for
machine mounting
Attach the CR700 to the
C70 grade rod clamp for
rod mounting
Contents
CR700 Receiver, C71 Magnet Clamp, C70 Grade Rod Clamp,
3 x AA Alkaline Batteries, User Guide
CR700 Quick Start
NOTE: Do not power
up receiving a laser
CR700 is ready after “CAL”
disappears from LCD