User Manual
Table Of Contents
- 1 Getting Started
- 1 About Your 5020 / 5040 Handset
- 1 Basic Handset Options
- 1 Making Calls
- 1 Answering Calls
- 1 During Calls
- 1 Using the Menu
- 1 Phone Book
- 1 Call Register
- 1 Messages
- 1.1 Writing and Sending a New Message
- 1.2 Saving a New Message in Outbox
- 1.3 Saving a New Message as a Template
- 1.4 Saving a Received Message as a Template
- 1.5 Sending Messages Using Templates
- 1.6 Reading a Message
- 1.7 Replying a Message
- 1.8 Forwarding a Message
- 1.9 Resending a Message
- 1.10 Erasing a Single Template
- 1.11 Erasing a Single Message
- 1.12 Erase All Read Messages from Inbox
- 1.13 Erase All Messages from Inbox
- 1.14 Erase All Messages from Outbox
- 1.15 Erase All Messages
- 1 Status
- 1 Settings
- 1.1 Ringing Volume
- 1.2 Ringing Tone
- 1.3 Alerting Volume
- 1.4 Vibrator
- 1.5 Silent Mode
- 1.6 Auto Key Lock
- 1.7 Backlight
- 1.8 Auto Answer
- 1.9 Out of Range
- 1.10 Bluetooth (only KIRK 5040)
- 1.10.1 Activate Bluetooth Function
- 1.10.2 Pair Wireless Headset with the Handset
- 1.10.3 Deactivate Bluetooth
- 1.10.4 Activate Bluetooth Again
- 1.10.5 Disconnect Wirelees Headset.
- 1.10.6 Connect Wireless Headset again
- 1.10.7 Remove Wireless Headset from the Device List
- 1.10.8 Auto Connect
- 1.10.9 Wireless Headset Volume
- 1.10.10 Switch Between Wireless Headset and Handset
- 1.10.11 Last Number Redial
- 1.11 Advanced...
- 1 General Information
Note: If one of the systems not chosen is removed, the handset remains connected to
the system in use.
1.11.4.3 Creating a Login
To create a login, the system must allow subscriptions to be made. Some systems also
require an Authentication Code (AC). If more than one system currently permits sub-
scription, you will need to know the ID of the system to which you want to subscribe.
Authentication Codes and system ID’s will be provided be the system administrator.
You can subscribe up to 10 systems, that is create 10 logins.
Press
Menu to enter main menu.
Scroll to
Settings and press Select.
Scroll to
Advanced and press Select.
Scroll to
Login and press Select.
Scroll to
Create login and press Select. The handset will start searching for a
system.
Scroll to the found system and press
Select.
If required, enter an AC Code and press
Ok to connect to the system.
Press
Ok.
Note: If the handset is already subscribed to 10 systems, you will have to remove a
subscription before creating a new subscription (refer to “Removing a Login” on page 59).
1.11.4.4 Selecting Login Automatically
When auto login is turned on, the handset automatically change to another system
when necessary. Auto login should only be used when systems are separate, with no
overlaps.
Note: To activate auto login your handset must be subscribed to at least two systems.
Press
Menu to enter main menu.
Scroll to
Settings and press Select.
Scroll to
Advanced and press Select.
Scroll to
Login and press Select.
Scroll to
Auto login and press Select.
If
Off is selected, press Change to select On.
The handset automatically selects a system. The selected system is marked with an
A.