Installation Guide

5. Secure The Top Track
Swing the track back to its
original position. After
making pilot holes (with a nail
or a 3/32” drill bit), drive the
1” track screws through all
track holes. Be sure to set
all screws in track as straight
and tight as possible to ensure
smooth operation
of the door.
6. Secure The Anchor Panel
Use the closure channel to
measure and align the channel
clips. Align the channel on the
non-opening side of the door
jamb. Make sure the top of
the channel is straight up and
down.
Mark each of the ve closure
channel screw holes and
remove the closure channel.
Make pilot holes (with a nail or
a 3/32” drill bit) and install the
channel clips, using ve of the
1” roundhead screws. Align
the clips vertically and press the door anchor panel onto
them until it snaps into place.
7. Secure The Closure Channel
Align the closure channel on the
opening side of the door jamb.
Make sure the channel is straight
up and down.
Mark each of the ve screw holes
(as above). If necessary, cut the
channel to match the door size.
Make pilot holes in door jamb (with
a nail or a 3/32” drill bit) and install
the closure channel, using ve of
the 1” athead screws.
8. Install the Door Locking Clip
Align the locking clip with the predrilled pilot hole located
on the lead edge (between the door handles). Install the
locking clip by using a 1”
athead screw.
Figure A.
Attach the
Striker plate
Door
Magnet
Closure
Channel
80”
Closure
Channel
96”
DOUBLE DOOR DOOR INSTALLATION
1.Measure The Door Opening
Divide the width of the opening by two. Cut each top track
to this measurement so that when installed, the tracks butt
against one another in the center of the door opening.
It is also acceptable to use one track if it will t your opening.
To Trim Height and Top Track
Stack the door panels together and secure with masking
tape. Remove bottom hinge screws. Cut excess with a
hacksaw or ne tooth saw. Cut the top track 1/8”shorter than
the width of the opening. Reinsert hinge screws.
2. Install Top Track
On a center line drawn across the top of the door opening,
install either half track and install all screws in the half track. if
using a single track, use one center screw.
3. Install the Handles
Tap the two handle attachment pins into one handle, then t
the pins through the door panel holes. Press the other handle
onto the pins.
If necessary, you may back one handle with a solid object and
tap the other handle alternately over each pin area until the
handles are seated. Do not strike the middle of either handle.
4. Install The Door Panels
Install the two doors in the half track with lead edges facing
each other. If necessary install the second track and push
one door onto this track. Set a track screw at the track
center joint and leave the screw projecting down 1/2” to
prevent glides from passing the joint.
If using a single track, swing one end of the top track out of
the door opening and slide the top glides for both doors onto
the track near the center screw. Swing the track back to its
original position. After making pilot holes, install the 1” track
screws through all track holes. Be sure to set all screws as
straight and tight as possible to ensure smooth operation of
the door.
5. Secure The Anchor Panel
Use the closure channel to measure and align the channel
clips. Align the channel on the non-opening side of the door
jamb. Make sure the top of the channel is straight up
and down.
Mark each of the ve closure channel screws holes and
remove the closure channel. Make pilot holes (with a nail or
a 3/32 drill bit) and install the channel clips, using ve of the
1” roundhead screws. Align the clips vertically and press the
door anchor other panel onto them until it snaps into place.
Repeat on the other door jamb.
6. Install The Closure Channel
Align the closure channel on the lead edge of this door so
that it is ush with the top and bottom of the door. Mark each
of the ve screw holes on the lead edge and drill ve pilot
holes with a 3/32” bit. Install the closure channel using ve 1”
athead screws.
7. Install Door Locking Clip
Align the locking clip with the predrilled pilot hole located on
the lead edge (between the door handles). Install the locking
clip by using a 1” athead screw.
Channel Clips
125 Rt. 61 Schuylkill Haven, PA 17972
1-800-360-1585 • fax [phone]
www.ltlhomeproducts.com
Figure A