Instructions / Assembly

SINGLE DOOR INSTALLATION
1. Measure the Door Opening
If the height of your door
opening is approximately 80”,
you will not need to alter the
door itself. If the opening is
less than 80” high, the door
may be shortened by sawing
o excess from the bottom of
the door panels.
If the opening is less than 80”
high: Stack the door panels
together, secure with masking
tape, measure the amount you
need to trim and make a clear mark on the masking
tape. Cut with a hacksaw or ne tooth saw. You
can use sand paper to smooth any rough edges.
Remove the masking tape.
6. Secure The Anchor Panel
Slide the entire door
against the non-opening
side of the doorway.
With the door panel
hanging naturally, locate
the three holes on the
anchor panel where the
door will be secured to
the jamb. Install the 1”
anchor screws through
the washers and secure the door to the jamb.
7. Install Magnetic Latch Striker Plate
Place the magnetic latch striker plate against the
metal strips on the door edge. Close the door
until it strikes the door jamb. Mark the proper
location of the latch. Secure the latch to the door
jamb with the two 1/2” athead screws.
Secure in
the Channel
Align
Striker
Plate
Closure
Channel
80”
Closure
Channel
96”
Make Sure
All The
Following
Parts Are
Included
With Your
Folding
Door:
Anchor Screws
Tornillos de fijación
Vis d'ancrage
Top Track
Guía superior
Rail pour le haut
Striker Plate
Placa de encastre
Plaque à gâche
Handle
Manija
Poignée
Lead Edge Door
Borde delantero de la puerta
Bord avant de la porte
Top Glides
Patines superiores
Patins pour le haut
Anchor Panel
Panel de fijación
Panneau d'ancrage
Anchor Screw
Tornillo de fijación
Vis d'ancrage
Door Parts Location
HORIZON/FIJI
INSTALLATION INSTRUCTIONS
For quick and easy installation of your folding door,
read these instructions thoroughly. A few minutes of
prior planning will make the job easier and will ensure
years of trouble-free use.
The Tools You Will Need
You will need a small #1 Phillips screwdriver, a tape
measure, a small nail, and a 3/32” drill for screw pilot
holes, a hacksaw or ne tooth saw (saw needed to
trim top track for the appropriate width or to trim
height of panels if opening is less than 80” high); and
masking tape (to secure doors if trimming is neces-
sary.) Safety glasses.
4. Install the Door Panels
Apply track lubricant to each top glide. Swing
one end of the overhead track out of the door
opening to accept the top glides. Decide if you
want the door to open from the left or the right,
then slide all top glides onto the track. Stack the
panels together near the center screw.
5. Secure The Top Track
Swing the track back to its original position.
After making screw pilot holes (with a nail or a
3/32” drill), drive the 3/4” track screws through
all track holes. Set all screws as straight and
tight as possible to assure smooth operation of
the door.
2. Install the Top Track
Cut the Top track 1/8”
shorter than the door
opening. Position the top
track on the top of the
door opening so that it
is straight and centered.
After making a screw pilot
hole (with a nail or 3/32” drill), drive a 3/4” track
screw through the screw hole nearest the center
of the track. Do not tighten. (Tape may be used to
hold the track in place while you mark and drill.)
3. Install the Handles
Tap the two handle attachment pins into one
handle, then t the pins through the door panel
holes. Press the other handle onto the pins.
If necessary, you
may back one
handle with a solid
object and tap the
other handle alter-
nately over each pin
area until the
handles are seated.
Do not strike the middle of either handle.
1 Top Track
1 Magnetic Latch
Striker Plate
2 Handles
2 Handle
Attachment Pins
4 Track Screws
(3/4”)
2 Flathead Screws
(1/2”)
3 Washers
3 Anchor Screws
(1”)
Lubricant
Double Door Installation
Doors can be used as a Double door but due to
the magnets, there will be approximately a 0.25”
gap when the doors are in the closed position.
1. Measure the Door Opening
Divide the width of the opening by two. Cut
each top track to this measurement so that when
installed, the tracks butt against one another in
the center of the door opening.
2. Install One Top Track
On a center line drawn across the top of the door
opening, install either half track and install all
screws in the half track.
3. Install the Handles
Tap the two handle attachment pins into one
handle, then t the pins through the door panel
holes. Press the other handle onto the pins.
Repeat with the other handle.
4. Install the Top Glides
Position top glides over center holes on top of
each full width panel. Snap top glides into place
and make sure they are secure.
To secure the lead edge top glide, place the T
shaped part inside the lead edge and align the
holes. Then insert the female section from the
outside hole through the hole in the T shaped
glide through the other side of the lead edge.
Then insert the threaded male screw into the
female part and tighten until snug. Repeat with
the other door.
5. Install Second Track and Door Panels
Apply track lubricant to each top glide. Install the
two doors in the half track with lead edges facing
each other. Then install the second track and
push one door onto this track. Set a screw at the
track center joint and leave the screw projecting
down 1/2” to prevent glides from passing the
joint.
6. Secure Anchor Panels
Slide one door against the door jamb. With the
door panel hanging naturally, locate the holes on
the anchor panel where the door will be secured
to the jamb. Using the drill, insert the screws and
secure the end anchor panel to the jamb. Repeat
with the other door.
To close the doors, pull together until
magnets latch.