Instructions / Assembly

• Small #1 Phillips type screwdriver • tape measure
• small nail • 3/32” drill bit for pilot holes • hacksaw
or ne tooth saw (saw needed to trim top track for
the appropriate width or to trim height of panels if
opening is less than 80” high) • masking tape (to
secure doors if trimming is necessary)
• Safety glasses.
SINGLE DOOR INSTALLATION
1. Measure the Door Opening
If the height of your door
opening is approximately 80”,
you will not need to alter the
door itself. If the opening is
less than 80” high, the door
may be shortened by sawing
o excess from the bottom of
the door panels (end without
holes).
If you need to trim the
height of the door: Stack the
door panels together, secure
with masking tape and cut with a hacksaw or ne
tooth saw. Cut the overhead track 1/8” shorter
than the width of the opening.
The width of the door cannot be altered.
7. Secure The Anchor Panel
Slide the entire door against
the non-opening side of
the doorway. With the door
panel hanging naturally,
locate the holes on the
anchor panel where the door
will be secured to the jamb.
Using the drill, insert the
screws and secure the end anchor panel
to the jamb.
8. Install Magnetic Latch Striker Plate
Place the magnetic latch striker plate against the
magnet on the lead edge. Close the door until it
strikes the door jamb. Mark the top and bottom
location of the striker plate on the jamb. Align the
striker plate on the marked location and secure
to the jamb with two athead screws.
SIENNA
INSTALLATION INSTRUCTIONS
For
quick and easy installation of your folding door,
read these instructions thoroughly. A few minutes
of prior planning will make the job easier and will
ensure years of trouble-free use.
The Tools You Will Need
Double Door Installation
Doors can be used as a Double door but due to the
magnets, there will be approximately a 0.25” gap
when the doors are in the closed position.
1. Measure the Door Opening
Divide the width of the opening by two. Cut each top
track to this measurement so that when installed, the
tracks butt against one another in the center of the
door opening.
2. Install One Top Track
On a center line drawn across the top of the door
opening, install either half track and install all screws
in the half track.
3. Install the Handles
Tap the two handle attachment pins into one handle,
then t the pins through the door panel holes. Press
the other handle onto the pins.
Repeat with the other handle.
4. Install the Top Glides
Position top glides over center holes on top of each
full width panel. Snap top glides into place and make
sure they are secure.
To secure the T-style lead edge top glide, place the T
shaped part inside the lead edge and align the holes.
Then insert the female section from the outside hole
through the hole in the T shaped glide through the
other side of the lead edge. Then insert the threaded
male screw into the female part and tighten until snug.
Repeat with the other door.
5. Install Second Track and Door Panels
Apply track lubricant to each top glide. Install the two
doors in the half track with lead edges facing each
other. Then install the second track and push one door
onto this track. Set a screw at the track center joint
and leave the screw projecting down 1/2” to prevent
glides from passing the joint.
6. Secure Anchor Panels
Slide one door against the door jamb. With the door
panel hanging naturally, locate the holes on the anchor
panel where the door will be secured to the jamb.
Using the drill, insert the screws and secure the end
anchor panel to the jamb. Repeat with the other door.
To close the doors, pull together until
magnets latch.
Secure in
the Channel
Align
Striker
Plate
Closure
Channel
80”
Closure
Channel
96”
Asegúrela en
el canal
Alinee
la placa
de
encastre
Make Sure All
The Following
Parts Are
Included With
Your Folding
Door:
Anchor Screws
Tornillos de jación
Top Track
Guía superior
Striker Plate
Placa de encastre
Handle
Manija
Lead Edge
Borde delantero de la puerta
Top Glides
Patines superiores
Anchor Panel
Panel de jación
T-Style Top Guide
Patín superior en forma de T
Magnet
Magnética
Door Parts Location
Handle
Handle
1 Overhead Track
2 Handles Pins
12 Track & Anchor
Screws
3 Flathead Screws
(1 Spare)
1 Magnetic Latch
Striker Plates
Female & Male
Connectors
1 T Style
Top-Glide
8 Top Glides
(1 Spare)
4. Install The Top Glides
Position top glides over center holes on top of
each full width panel.
Snap top glides into
place and make sure
they are secure. To
secure the T-style
lead edge top glide,
place the T shaped
part inside the lead
edge and align the
holes. Then insert
the female section
from the outside hole
through the hole in
the T shaped glide
through the other side
of the lead edge.
Then insert the threaded male screw into the
female part and tighten until snug.
5. Install the Door Panels
Apply track lubricant to each top glide. Swing
one end of the top track out of the door opening
to accept the top glides. Decide if you want the
door to open from the left or the right, then slide
all top glides onto the track. Stack the panels
together near the center screw.
6. Secure The Top Track
Swing the track
back to its original
position. After
making pilot holes
(with a nail or a
3/32”drill bit), drive
the track screws
through all track
holes. Set all
screws as straight
and tight as possible
to ensure smooth operation of the door.
2. Install the Top Track
Position the top track
on the top of the
door opening so that
it is straight and
centered. After
making a pilot hole
(with a nail or 3/32”
drill bit), drive a track
screw through the
screw hole nearest the center of the track. Do
not tighten. (Tape may be used to hold the track
in place while you mark and drill.)
3. Install the Handles
Tap the two handle
attachment pins into
one handle, then t
the pins through the
door panel holes.
Press the other handle
onto the pins.
If necessary, you may back one handle with a
solid object and tap the other handle alternately
over each pin area until the handles are seated.
Do not strike the middle of either handle.
1 Tube
of Track
Lubricant
Installation pdfs, videos, warranty registration and
replacement parts can be found on our website under
the Product Support section.
125 Route 61 • Schuylkill Haven, PA 17972
1.800.360.1585 • fax [phone]
www.ltlhomeproducts.com • e-mail: [e-mail]