Installation Instructions for Topload Washers Original Instructions Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.) www.alliancelaundry.com Part No.
Table of Contents Washer Dimensions and Specifications....................................................4 Installation............................................................................................. 5 Before You Start............................................................................................. 5 Supplies..................................................................................................... 5 Order of Installation Steps.............................................
Washer Dimensions and Specifications Washer Dimensions and Specifications Maximum spin speed of washer is 710 RPM. A B C D H G I J F E TLW2075N_SVG *With leveling legs turned into base. A 711 mm [28 in.] B 562 mm [22.13 in.] C *1346 mm [53 in.] D *1022 mm [40.25 in.] E 660 mm [26 in.] F 10 mm [0.4 in.] G 651 mm [25.63 in.] H *737 mm [29 in.] I *1092 mm [43 in.] J *914 mm [36 in.] © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 4 Part No.
Installation Installation Before You Start 1. Position washer near installation area. 2. Remove the shipping brace and shipping plug. 3. Wipe out the inside of the washtub 4. Connect the fill hoses. 5. Connect the drain hose to the drain receptacle. 6. Position and level the washer. 7. Connect the washer to electrical power. 8. Add water to the washer. 9. Check the lid switch. 10. Recheck steps 1-9.
Installation Connect Fill Hoses WARNING Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period and before using the washer, turn on all hot water taps and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. The gas is flammable. Do not smoke or use an open flame during this time.
Installation 4. Make sure the hose from the hot water tap goes to the water mixing valve marked “H” and the hose from the cold tap goes to the valve marked “C”. 5. Thread hose couplings onto valve connections finger tight. Then turn 1/4 turn with pliers. Connecting Hoses To comply with Australian water regulations and Australian standard AS/NZS3500.1, an approved dual check valve backflow prevention device with the watermark must be fitted at the point of connection(s) between the supply and the fitting.
Installation Connect Drain Hose to Drain Receptacle dealer or parts distributor. Installation instructions are supplied with the kit. 1. Remove the drain hose from its shipping position on the rear of the washer by unhooking the hose from the retainer clamp. 2. Install the drain hose into the drain receptacle (standpipe, wall or laundry tub) following the instructions below. 1 NOTE: Drain receptacle must be capable of handling a minimum of 32 mm [1-1/4 inch] outside diameter drain hose.
Installation Laundry Tub Installation For this type of installation, the drain hose MUST be secured to the stationary tub to prevent hose from disloding during use. Refer to Figure 9 . Use the beaded strap (supplied in accessories bag) to secure hose. We recommend leaving the standpipe adapter on the drain hose for this type of installation. 1 TLW2252N_SVG 1. Wood Block Figure 10 4. Place rubber cups (from accessories bag) on all four leveling legs. 1 TLW2222N_SVG 1 1.
Installation 7. Once adjusted, tilt the washer forward on front legs and lower back down into position to set the rear self-leveling legs. 8. Washer must not rock. When washer is level and does not rock, tighten locknuts securely against bottom of washer base. If these locknuts are not tight, washer will not remain stationary during operation. Improper installation or flexing of weak floor will cause excessive vibration.
Installation Earth/Ground Instructions This appliance must be properly connected to protective earth/ ground. In the event of malfunction or breakdown, the earth/ ground will reduce the risk of electric shock by providing a path of least resistance for electric current. The appliance is equipped with a cord having an equipment earth/ ground conductor and a three-prong earth/ground plug.
Installer Checklist Installer Checklist 1 Position Washer Near Installation Area. 6 Position and Level the Washer. NOTE: Tighten locknut after final adjustment. NOTE: Place rubber feet on all four leveling legs. CHECK 2 CHECK Remove the Shipping Brace and Shipping Plug. NOTE: Save the shipping brace and plug. They must be reinstalled whenever washer is moved or transported to a new location.
