Installation Instructions for Frontload Washers Original Instructions Keep These Instructions for Future Reference. CAUTION: Read the instructions before using the machine. (If this machine changes ownership, this manual must accompany machine.) www.speedqueen.com Part No.
Table of Contents Washer Dimensions................................................................................ 4 Installation............................................................................................. 5 Before You Start............................................................................................. 5 Tools..........................................................................................................5 Parts Included...............................................
Washer Dimensions Washer Dimensions A B D C J E H F G I FLW2450N_SVG Figure 1 A 24.06 in. [611 mm] B 40.42 in. [1027 mm] C 32 in. [813 mm] D 39.61 in. [1006 mm] E* 14.6 in. [371 mm] F 26.875 in. [683 mm] G 2.04 in. [52 mm] H 27.73 in. [704 mm] I (with door closed) 1.59 in. [40 mm] J 13.1 in. [333 mm] * For ADA compliance turn legs out from base 0.5 inches. © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 4 Part No.
Installation Installation Before You Start Parts Included Tools An accessories bag has been shipped inside your washer. It includes: For most installations, the basic tools you will need are: 1 • • • • • • 2 4 3 5 Parts Needed " 16 9/ Two fill hoses are required for installation. Order 807239 Hose Kit if needed. Kit includes two fill hoses color-coded for hot and cold water. 6 If using any other hoses, follow these requirements: 7 • • 8 • FLW2376N_SVG 1. 2. 3. 4. 5. 6. 7. 8.
Installation NOTE: For best performance and to minimize vibration or movement, install washer on a solid, sturdy and level floor. Some floors may need to be reinforced, especially on a second floor or over a basement. Do not install the washer on carpeting, soft tile or other weakly supported structures. Remove Shipping Materials 1. Remove two screws at bottom of front access panel. Rotate bottom of panel out and remove panel. FLW2451N_SVG Figure 3 2.
Installation Water Supply Requirements Water supply faucets must fit standard 3/4 inch [19 mm] female garden hose couplings. DO NOT USE SLIP-ON OR CLAMPON CONNECTIONS. NOTE: Water supply faucets should be readily accessible to permit turning them off when washer is not being used. Recommended cold water temperature is 50° to 75° Fahrenheit [10° to 24° Celsius]. Recommended maximum hot water temperature is 125° Fahrenheit [51° Celsius]. Warm water is a mixture of hot and cold water.
Installation IMPORTANT: Drain receptacle must be capable of handling a minimum of 1-1/4 inch [32 mm] outside diameter drain hose. the cold faucet goes to the valve marked “C”. Refer to Figure Figure 7 . 6. Then, using a pliers, screw approximately 1/4 turn. IMPORTANT: DO NOT cross thread or overtighten couplings. This will cause them to leak. 7. Turn water on and check for leaks. 8. If leaks are found, turn off the water, unscrew hoses and reinstall them until there are no leaks.
Installation Position and Level the Washer Wall Installation For installations of this type, the drain hose MUST be secured to one of the fill hoses using the beaded strap from accessories bag. Refer to Figure 9 . WARNING Washers elevated above floor level must be anchored to that elevated surface, base or platform.
Installation 2 Plug In the Washer 3 1 Electrical Requirements 120 Volt, 60 Hertz with 3-Prong Earth/Ground Plug NOTE: The wiring diagram is located in the control cabinet. WARNING 6 5 To reduce the risk of fire, electric shock, serious injury or death, all wiring and protective earth/ground connections MUST conform with the latest edition of the National Electrical Code, ANSI/NFPA No. 70, and such local regulations as might apply.
Installation Standard 120 Volt, 60 Hertz 3-Wire Effective Earth/ Ground Circuit led and connected to a protective earth/ground in accordance with all local codes and ordinances. WARNING 1 2 Improper connection of the equipment earth/ground conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the unit is properly connected to a protective earth/ground.
Installer Checklist Installer Checklist Fast Track for Installing the Washer 1 Position Washer Near Installation Area. 5 CHECK Position and Level the Washer. CHECK FLW2453N_SVG1 2 Remove the Shipping Materials and Install Plugs. 6 CHECK Wipe Out Inside of Washer. CHECK FLW2454N_SVG FLW2455N_SVG 3 Connect Fill Hoses. CHECK 7 COLD HOT CHECK FLW2304N_SVG 4 Plug In the Washer. TLW2289N_SVG Connect Drain Hose to Drain Receptacle.
