Metered Commercial Original Instructions Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.) www.alliancelaundry.com Installation/Operation Frontload Washers FLW1542C_SVG Part No.
WARNING Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 WARNING For your safety and to reduce the risk of fire or an explosion, do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
Table of Contents Safety Information..................................................................................6 Explanation of Safety Messages....................................................................... 6 Important Safety Instructions........................................................................... 6 Dimensions and Specifications................................................................ 8 Installation........................................................................
Maintenance......................................................................................... 21 User-Maintenance Instructions....................................................................... 21 Lubrication............................................................................................... 21 Cold Weather Care.................................................................................... 21 Care of Your Washer......................................................................
Safety Information Safety Information Explanation of Safety Messages Important Safety Instructions Precautionary statements (“DANGER,” “WARNING,” and “CAUTION”), followed by specific instructions, are found in this manual and on machine decals. These precautions are intended for the personal safety of the operator, user, servicer, and those maintaining the machine.
Safety Information • • • • • • • • • • • • • • Children less than three years should be kept away unless continuously supervised. Do not reach into the washer if the washtub or agitator, if applicable, is moving. Never operate the washer with any guards, panels and/or parts removed or broken. DO NOT tamper with the controls or bypass any safety devices. DO NOT operate individual units if they have been separated from a stack unit. Use your washer only for its intended purpose, washing clothes.
Dimensions and Specifications Dimensions and Specifications Models Equipped With Drain Hose A B D C E J H I F G FLW2333N_SVG A 24 in. [610 mm] B 44.34 in. [1126 mm] C 32 in. [813 mm] D 36.94 in. [938 mm] E* 14.6 in. [371 mm] F 26.875 in. [683 mm] G 2.04 in. [52 mm] H 27.73 in. [704 mm] I (with door closed) 1.59 in. [40 mm] J 13.1 in. [333 mm] * For ADA compliance turn legs out from base 0.5 inches. © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 8 Part No.
Dimensions and Specifications Models With Gravity Drain 1 A B D C E L J K F H G I FLW2334N_SVG 1. 1.5 in. [38 mm] Inside Diameter; 1.86 in. [47 mm] Outside Diameter A 24 in. [610 mm] B 44.34 in. [1126 mm] C 32 in. [813 mm] D 36.94 in. [938 mm] E* 14.6 in. [371 mm] F 26.875 in. [683 mm] G 4.2 in. [107 mm] H 4.1 in. [104 mm] I 2.04 in. [52 mm] J 27.73 in. [704 mm] K (with door closed) 1.59 in. [40 mm] L 13.1 in. [333 mm] * For ADA compliance turn legs out from base 0.5 inches.
Installation Installation NOTE: This appliance is suitable for use in countries having a warm, damp climate. Before You Start Tools Order of Installation Steps For most installations, the basic tools you will need are: 1 2 4 3 5 " 16 9/ 6 7 8 The proper order of steps must be followed to ensure correct installation. Refer to the list below when installing your unit. 1. Position washer near the installation area. 2. Remove the shipping materials. 3. Connect the fill hoses. 4.
Installation 2. Remove two 9/16 inch bolts and washers holding shipping brace to weight. 3. Remove two 9/16 inch bolts and washers holding shipping brace to washer base and remove brace. FLW2358N_SVG Figure 5 7. Replace front access panel. 8. Save all shipping materials. They must be reinstalled any time washer is moved more than four feet. IMPORTANT: Do not lift or transport unit from front or without shipping materials installed.
Installation WARNING 4 1 COLD HOT To prevent personal injury, avoid contact with inlet water temperatures higher than 125° Fahrenheit [51° Celsius] and hot surfaces. 2 8 7 W748 Maximum flow rate for all water temperatures is 2.5 gallons per minute [9.46 liters per minute] ± 15%. 6 1. 2. 3. 4. 5. 6. Filter Screen (Screen must be facing outward) Fill Hose Plain Rubber Washer Cold Water Connection Hot Water Connection Install this end of hose to valve connections at rear of washer 7.
Installation 1 1 2 W005I_SVG 1. Risers (Air cushions) 2. Water Supply Faucets FLW2337N_SVG 1. Shipping Tape Figure 7 Non-Gravity Drain Models - Connect Drain Hose to Drain Receptacle Remove the drain hose from its shipping position on the rear of the washer by removing the shipping tape. IMPORTANT: Drain receptacle must be capable of handling a minimum of 1-3/8 inch [35 mm] outside diameter drain hose. Figure 8 Standpipe Installation 1. Place the drain hose into the standpipe. 2.
Installation Gravity Drain Models - Connect Drain Outlet to Drain System Position and Level the Washer WARNING Maximum flow rate is 24 gallons/minute [90.8 liters/minute]. Flow rates will vary with load type. 1. Remove drain fitting (4 inches [102 mm] long) and hose clamp from accessories bag. Insert drain fitting into drain outlet hose. Clamp hose and fitting. 2. Connect the drain fitting to a vented drain system using a flexible connection (obtain locally). Inside diameter of fitting is 1.53 in.
Installation 3 2 1 NOTE: Hoses can be connected to either nozzle. 4. Refer to supply injection system instructions and label inside washer junction box cover ( Figure 14 ) for electrical connection. 5. Do not attempt to make supply injection electrical connections to points other than those provided specifically for that purpose by the factory. 6. Refer to supply injection system instructions for details on operation. Supply Injection System 6 5 4 1. 2. 3. 4. 5. 6.
Installation 1. Check the power supply for such characteristics as correct voltage, phase, and cycles to be certain they are correct for the washer. 2. Open manual shut-off valves to the washer. 3. Apply power to the washer. 3 2 1 Plug In the Washer Electrical Requirements 120 Volt, 60 Hertz with 3-Prong Earth/Ground Plug NOTE: The wiring diagram is located in the control cabinet.
Installation Standard 120 Volt, 60 Hertz 3-Wire Effective Earth/ Ground Circuit led and connected to a protective earth/ground in accordance with all local codes and ordinances. WARNING 2 3 1 8 Improper connection of the equipment earth/ground conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the unit is properly connected to a protective earth/ground.
Operation Operation Operation Instructions IMPORTANT: Prior to first wash, use an all-purpose cleaner, or a detergent and water solution, and a damp cloth to remove shipping dust from inside of washer. IMPORTANT: Remove all sharp objects from laundry to avoid tears and rips to items during normal machine operation. Load Laundry 1. Load items loosely into wash drum. (21 pounds [9.5 kg] maximum dry clothes load) NOTE: Small items such as baby socks may get caught around the door.
Operation Soil LIGHT MEDIUM Cycle NORMAL PERM PRESS Temp HOT WARM HEAVY DELICATES/ BULKY START COLD 4 S O F T E N E R LIQUID BLEACH P R E W A S H FLW2342N_SVG M A I N W A S H 1 Set Soil Level 3 2 1. 2. 3. 4. Figure 20 FLW2389N_SVG Main Wash Detergent Liquid Bleach Fabric Softener Pre-Wash Detergent 1. Push Soil Level touchpad to select LIGHT, MEDIUM or HEAVY. 2. LED light indicates selection.
Operation DRY2633N_SVG Start Washer MEDIUM Cycle NORMAL PERM PRESS Temp HOT DOOR is lit whenever the door is locked. The door cannot be opened when this light is on. START START flashes one second on and one second off when the full vend price has been satisfied. WARNING To reduce the risk of bodily injury, do not remove laundry from washer until all lights are out, and all moving parts have stopped.
Maintenance Maintenance User-Maintenance Instructions Replacing Hoses Lubrication Hoses and other natural rubber parts deteriorate after extended use. Hoses may develop cracks, blisters or material wear from the temperature and constant high pressure they are subjected to. All moving parts are sealed in a permanent supply of lubricant or are equipped with oilless bearings. Additional lubrication will not be necessary. Do not lubricate the door hinge. If the hinge makes noise, replace the hinge.
Maintenance 1. 2. 3. 4. 5. 6. 7. 8. Disconnect washer from electrical supply. Remove two screws at bottom of front access panel. Rotate bottom of panel out and remove panel. Attach shipping brace to weight and base using four bolts and washers. Refer to Figure 25 . Reinstall front access panel. Go to rear of washer to install rear shipping bolt, washer, spacer assemblies. Insert shipping bolt assemblies into each shipping bolt hole. Refer to Figure 26 .
Troubleshooting Troubleshooting Try these troubleshooting tips before making a service call. They may save you time and money. Washer Symptom Possible Cause/Solution Won’t Fill • • • • • • • • Make sure power cord is plugged all the way into the electrical outlet. Check the laundry room fuse or circuit breaker. Make sure that the controls are properly set. Press START keypad. Make sure that the loading door is closed tightly. Make sure hot and cold water faucets are turned on.
Troubleshooting Washer Symptom Water Leaks Possible Cause/Solution • • • • • • • • Too Many Soap Suds • • • Vibrates/Moves Slightly • • • Check that fill hoses are properly installed on the faucets and the washer’s water mixing valve. Check the condition of the fill hoses. Replace fill hoses every five years. Make sure drain receptacle is not clogged. Check laundry room plumbing. Check the condition of the rubber door gasket for tears or holes. Laundry load may be oversudsing.
Contact Information Contact Information If service is required, contact the nearest Factory Authorized Service Center. Serial Number _______________________________ If you are unable to locate an authorized service center or are unsatisfied with the service performed on your unit, contact: Alliance Laundry Systems Shepard Street P.O. Box 990 Ripon, WI 54971-0990 U.S.A. www.alliancelaundry.
Installer Checklist Installer Checklist Fast Track for Installing the Washer 1 Position Washer Near Installation Area. 5 CHECK Gravity Drain Models Connect Drain Outlet to Drain System. CHECK FLW2339N_SVG1 2 Remove the Shipping Materials and Install Plugs. 6 CHECK Position and Level the Washer. CHECK FLW2359N_SVG FLW2335N_SVG1 3 Connect Fill Hoses. 7 COLD Wipe Out Inside of Washer.
