Metered Commercial Original Instructions Keep These Instructions for Future Reference. CAUTION: Read the instructions before using the machine. (If this machine changes ownership, this manual must accompany machine.) www.alliancelaundry.com Installation/Operation Topload Washers TLW12C_SVG Part No.
WARNING Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 WARNING For your safety and to reduce the risk of fire or an explosion, do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
Table of Contents Safety Information..................................................................................6 Explanation of Safety Messages....................................................................... 6 Important Safety Instructions........................................................................... 6 Dimensions............................................................................................. 8 Installation..............................................................
Control Modes.......................................................................................... 22 Rapid Advance..........................................................................................23 Setting Dipswitches................................................................................... 23 Operation Instructions for MDC Washers........................................................ 23 Add Detergent..................................................................................
Safety Information Safety Information Explanation of Safety Messages Important Safety Instructions Precautionary statements (“DANGER,” “WARNING,” and “CAUTION”), followed by specific instructions, are found in this manual and on machine decals. These precautions are intended for the personal safety of the operator, user, servicer, and those maintaining the machine.
Safety Information • • • • • • • • • • • • • Children less than three years should be kept away unless continuously supervised. Do not reach into the washer if the washtub or agitator, if applicable, is moving. Never operate the washer with any guards, panels and/or parts removed or broken. DO NOT tamper with the controls or bypass any safety devices. Use your washer only for its intended purpose, washing clothes. Always follow the fabric care instructions supplied by the garment manufacturer.
Dimensions Dimensions Metered Models B A 1 C C H J K M L E D I H G F TLW2051N_SVG 1. Pilot Hole A - Electronic Control Models 22.44 in. [570 mm] B - Coin Slide Models 21.56 in. [548 mm] C 51 in. [1295 mm] D - Standard Capacity Meter Case 43 in. [1092 mm] D - High Capacity Meter Case 43.875 in. [1114 mm] E - Electronic Control Models 38.19 in. [970 mm] E - Coin Slide Models 40.38 in. [1026 mm] F 28 in. [711 mm] G 26 in. [660 mm] H 0.44 in. [11 mm] I 36 in.
Dimensions Nonmetered Models A C B H C H I K J G F E TLW2050N_SVG D A 21.56 in. [548 mm] B 51 in. [1295 mm] C 40.38 in. [1026 mm] D 28 in. [711 mm] E 26 in. [660 mm] F 0.44 in. [11 mm] G 36 in. [914 mm] H 41.25 in. [1048 mm] I 28.75 in. [730 mm] J 25.63 in. [651 mm] K 30.5 in. [775 mm] © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 9 Part No.
Installation Installation Before You Start Tools For most installations, the basic tools you will need are: 2 1 2. 3. 4. 5. 6. 7. 8. 9. Wipe out inside of the washer. Connect the fill hoses. Connect the drain hose to the drain receptacle. Position and level the washer. Plug in the washer. Add water to the washer. Check the lid switch. Check installation. Remove the Shipping Brace and Shipping Plug 3 4 5 6 1. Remove the shipping brace from under the lid. 2.
Installation 1 3 2 TLW2099N_SVG Figure 3 TLW2098N_svg Connect Fill Hoses 1. Shipping Brace 2. Shipping Plug 3. Cardboard Base WARNING Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period and before using the washer, turn on all hot water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas.
Installation 8. Continue tightening and rechecking until no leaks are found. Water Supply Requirements Water supply faucets must fit standard 3/4 inch [19 mm] female garden hose couplings. DO NOT USE SLIP-ON OR CLAMPON CONNECTIONS. COLD HOT NOTE: Water supply faucets should be readily accessible to permit turning them off when washer is not being used. 4 1 2 3 C H 8 Recommended cold water temperature is 50° to 75° Fahrenheit [10° to 24° Celsius].
Installation 1 1 3 2 2 1. Drain Hose 2. Standpipe 3. Recommended Standpipe Height 36 in. [914 mm] Minimum W005I_SVG 1. Risers (Air cushions) 2. Water Supply Faucets Figure 6 Figure 5 Connect Drain Hose to Drain Receptacle IMPORTANT: The drain hose installation is a very important factor in the washer installation. If care is not taken when the drain hose is installed, a siphoning action can be started which will cause water to be siphoned from the washer during the cycle.
Installation 1 1 2 2 5 4 { 4 3 3 TLW2210N_SVG 1. Drain Hose 2. Cut Drain Hose off at This End to Fit the Washer Installation 3. Standpipe 4. Maximum Standpipe Height Not To Exceed 5 ft. [1.5 m] Low Standpipe Installation If the drain facility is lower than the cabinet top, a siphon break kit, Part No. 562P3, must be installed in the drain hose to prevent siphoning action and drain hose MUST be cut to fit the washer installation. Refer to Figure 8 . Use one No. 25863 Hose Coupling to splice hose.
Installation NOTE: For areas with uneven floors, a No. 566P3 Adjustable Rear Leg Extension Kit is available as optional equipment at extra cost. 8. Verify that unit does not rock. 1 2 • DO NOT operate other appliances on the same circuit. Use separately fused 15 Amp circuits.
Installation Add Water to the Washer WARNING To reduce the risk of an electric shock or fire, DO NOT use an extension cord or an adapter to connect the washer to the electric power source. W082 Earth/Ground Instructions This appliance must be properly connected to protective earth/ ground. In the event of malfunction or breakdown, the earth/ ground will reduce the risk of electric shock by providing a path of least resistance for electric current.
Installation 2. Run washer through one complete cycle to make sure it is operating properly. 2 3 Vending 1 Meter Case 4 The factory mounted coin meter case does not include the service door lock, coin slide (if applicable), coin drawer, coin drawer lock or keys. These parts must be ordered (at extra cost) according to the purchaser’s requirements direct from the manufacturer of your choice. 7 5 NOTE: You have the option of using a screw type lock or a 1/4 turn lock on the meter case service door.
Installation 6. Install coin slide extension assembly onto top of coin slide using two remaining screws and lockwashers. Place lockwasher under head of screws, above bracket “A”. Refer to Figure 16 . 2 1 TLW2164N_SVG 1. Coin Slide Extension Assembly 2. Spring Installed Figure 16 7. Before installing coin slide and extension, make sure ground wire is tucked under control shield to provide clearance for coin slide. Refer to Figure 17 . 1 Installing Coin Slide Assembly Into Meter Case: Option Two 1.
Installation • • • Bit (No. 12 screws) Part No. 282P4 Control panel tamper-resistant screw Part No. 35528 Front panel tamper-resistant screw Part No. 35527 1 The following list is the procedure required to install the Phillips head screw and tamper-resistant screws: 2 WARNING Any disassembly requiring the use of tools must be performed by a suitably qualified service person.
Operation Operation Operation Instructions for Coin Slide Operated and Nonmetered Washers IMPORTANT: Prior to first wash, use an all-purpose cleaner, or a detergent and water solution, and a damp cloth to remove shipping dust from inside of washer. IMPORTANT: Remove all sharp objects from laundry to avoid tears and rips to items during normal machine operation. Add Detergent 1. Pour measured amount of detergent into washtub. Refer to package directions. 2. NEVER POUR UNDILUTED BLEACH DIRECTLY ON LAUNDRY.
Operation DELICATE DELICATE TLW2243N_SVG PERM PRESS COLD PERM PRESS/COLD TLW2244N_SVG PERM PRESS WARM PERM PRESS/WARM TLW2048N_SVG TLW2245N_SVG NOTE: Cycle Selector may be changed any time before first wash fill is complete. Figure 24 Indicator Lights Start Washer IN USE Metered Models 1. Insert money by placing coin(s) in slide. 2. Carefully push slide in as far as possible and then pull slide out as far as possible. 3. The IN USE light will come on indicating start of cycle.
Operation Control Modes Power-Up Mode The control enters this mode after power is applied to the washer. In Power-Up Mode, the control will detect the state it was in at power-down to determine what mode to enter. After the control completes operation in the Power-Up Mode, it will enter either the Ready, Test or Run Modes. Ready Mode In Ready Mode, the control will wait for the vend to be satisfied before entering Run Mode.
Operation No Flow Error During a Fill step, the control will wait 30 seconds for the pressure sensor to stabilize and then take an initial water level reading. The control takes a second reading after 4.5 minutes. If the difference between the two readings is not greater than 1.5 inches, the control will set a No Flow Error. This usually indicates that the machine does not have enough water pressure or the pressure value is not changing. The IN USE LED will flash four times to indicate this condition.
Operation TLW2202N_SVG Figure 27 W395I_SVG Figure 25 Set Fabric Selector and Wash Temperature Push touchpad for NORMAL/HOT, NORMAL/WARM, NORMAL/COLD, PERM PRESS/WARM or DELICATES/COLD cycle. Light indicates selection. Load Laundry 1. Load dry clothes loosely into washtub – DO NOT overload! (14 lbs. [6.3 kg] maximum dry clothes load) 2. When washing large items such as shag rugs and bedspreads, add several small items to balance wash load.
Operation To Insert Card SPIN SPIN is lit during the Final Spin portion of the cycle. START START flashes one second on and one second off when the full vend price has been satisfied. Insert card into opening. WARNING To reduce the risk of bodily injury, do not remove laundry from washer until all lights are out, and all moving parts have stopped. W092 The washer will stop (pause) shortly before the first spin. DRY2633N_SVG Figure 30 Start Washer 1.
Maintenance Maintenance User-Maintenance Instructions Cold Weather Care If the unit is delivered on a cold day (below freezing), or is stored in an unheated room or area during the cold months, do not attempt to operate the washer until it has had a chance to warm up. Water from the previous cycle may remain. Care of Your Washer Use only a damp or sudsy cloth for cleaning the control panel. Some cleaning products may harm the finish on the control panel or damage the interior.
Maintenance If the overload protector stops motor again, remove the washer from use and call the service person to correct the problem. © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 27 Part No.
Troubleshooting Troubleshooting Try these troubleshooting tips before making a service call. They may save you time and money. Washer Symptom Won’t Fill Possible Cause/Solution • • • • • • • • • • • • • • Make sure lid is closed. Make sure power cord is plugged all the way into the electrical outlet. Check the laundry room fuse or circuit breaker. Insert coin(s) or card. (metered models only) Check for proper operation of coin slide switch (coin slide models only).
Troubleshooting Washer Symptom Won’t Spin Possible Cause/Solution • • • • • • • • Stops/Pauses During Cycle • • • Make sure lid is closed. Make sure power cord is plugged all the way into the electrical outlet. Check the laundry room fuse or circuit breaker. Insert coin(s) or card. (metered models only) Push START switch to start the washer (nonmetered models only). The motor overload protector may have stopped the cycle.
Contact Information Contact Information If service is required, contact the nearest Factory Authorized Service Center. Model Number If you are unable to locate an authorized service center or are unsatisfied with the service performed on your unit, contact: Alliance Laundry Systems Shepard Street P.O. Box 990 Ripon, WI 54971-0990 U.S.A. www.alliancelaundry.com Phone: +1 (920) 748-3121 Serial Number Please include a copy of your bill of sale and any service receipts you have.
Installer Checklist Installer Checklist Fast Track for Installing the Washer 1 Remove the Shipping Brace and Shipping Plug. 5 CHECK Position and Level the Washer. CHECK TLW2098N_SVG1 TLW2201N_SVG 2 Wipe Out Inside of Washer. 6 CHECK Plug In the Washer. CHECK TLW2289N_SVG TLW2099N_SVG 3 Connect Fill Hoses. 7 Add Water to the Washer. COLD CHECK HOT CHECK TLW2056N_SVG TLW1988N_SVG 4 Connect Drain Hose to Drain Receptacle. 8 CHECK Check Lid Switch.
