Installation Instructions for Topload Washers Original Instructions Keep These Instructions for Future Reference. CAUTION: Read the instructions before using the machine. (If this machine changes ownership, this manual must accompany machine.) www.speedqueen.com Part No.
Table of Contents Dimensions and Specifications................................................................ 4 Installation............................................................................................. 5 Before You Start............................................................................................. 5 Supplies..................................................................................................... 5 Parts Included....................................................
Dimensions and Specifications Dimensions and Specifications A B C D H G I J F E TLW2340N_SVG A 28 in. [711 mm] B 22.13 in. [562 mm] C (to controls) Electronic Control: *41.25 in. [1048 mm] Knob Control: *40.75 [1035 mm] D *53 in. [1346 mm] E 26 in. [660 mm] F 0.4 in. [10 mm] G 25.63 in. [651 mm] H *29 in. [737 mm] I *42.75 in. [1086 mm] J *36 in. [914 mm] *With leveling legs turned into base. © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 4 Part No.
Installation Installation Before You Start Parts Included Supplies An accessories bag has been shipped inside your washer. It includes: For most installations, the basic supplies you will need are: • • • • • 2 1 3 Two filter screen washers Two plain rubber washers Four rubber feet Beaded strap Product literature Parts Needed Two fill hoses are required for installation. Order 807239 Hose Kit if needed. Kit includes two fill hoses color-coded for hot and cold water.
Installation Remove the Shipping Brace and Shipping Plug Wipe Out Inside of Washtub Prior to first wash, use an all purpose cleaner or a detergent and water solution and a damp cloth to remove shipping dust from inside of washtub. 1. Remove the shipping brace from under the lid. 2. The shipping plug will be released from the base of the washer when removing the cardboard base from the washer.
Installation NOTE: Water supply faucets should be readily accessible to permit turning them off when washer is not being used. IMPORTANT: Turn off water supply whenever there will be an extended period of non-use. 4 Recommended cold water temperature is 50° to 75° Fahrenheit [10° to 24° Celsius]. Recommended maximum hot water temperature is 125° Fahrenheit [51° Celsius]. Warm water is a mixture of hot and cold water.
Installation NOTE: Machine will not drain if standpipe is higher than 8 feet [2438 mm]. 2. Place the drain hose into the standpipe. IMPORTANT: To prevent siphoning, do not place any ribbed portion of the drain hose into the standpipe. 3. Remove the beaded strap from accessories bag and place around standpipe and drain hose, approximately 12 inches [300 mm] down from the top of pipe. Refer to Figure 5 . 1 3 a. Insert the end of the beaded strap into the larger hole found on the end of the strap. b.
Installation Laundry Tub Installation 4. Place rubber cups (from accessories bag) on all four leveling legs. For this type of installation, the drain hose MUST be secured to the stationary tub to prevent hose from disloding during use. Use the beaded strap (supplied in accessories bag) to secure hose. 1 5 1 2 4 TLW2284N_SVG 1. Beaded Strap (tape if necessary) 1. 2. 3. 4. 5. Figure 8 Position and Level the Washer 1. Position washer so it has sufficient clearance for installation and servicing. 2.
Installation Plug In the Washer Standard 120 Volt, 60 Hertz 3-Wire Effective Earth/ Ground Circuit Electrical Requirements 120 Volt, 60 Hertz with 3-Prong Earth/Ground Plug NOTE: The wiring diagram is located in the control hood. 1 WARNING 2 3 6 8 To reduce the risk of fire, electric shock, serious injury or death, all wiring and protective earth/ground connections MUST conform with the latest edition of the National Electrical Code, ANSI/NFPA No. 70, and such local regulations as might apply.
Installation led and connected to a protective earth/ground in accordance with all local codes and ordinances. Check Lid Lock To check lid lock, start a cycle. Once the red Lid Locked status light is lit and stops flashing, make sure the lid has locked. WARNING Improper connection of the equipment earth/ground conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the unit is properly connected to a protective earth/ground.
Installer Checklist Installer Checklist Fast Track for Installing the Washer 1 Remove the Shipping Brace and Shipping Plug. 5 CHECK Position and Level the Washer. CHECK TLW2201N_SVG TLW2280N_SVG1 2 Wipe Out Inside of Washtub. 6 CHECK Plug In the Washer. CHECK TLW2289N_SVG TLW2281N_SVG1 3 Connect Fill Hoses. CHECK 7 Check Lid Lock. CHECK COLD HOT TLW1988N_SVG 4 Connect Drain Hose to Drain Receptacle. CHECK TLW2288N_SVG Refer to the manual for more detailed information.
