User Manual

Quick Start Guide
AX1800 Dual Band Gigabit WiFi Router
Model: KX450
Solid on
Awaiting the WPS connection.
Blinking slowly
Starting up or connected to the Internet.
Failed to connect to the Internet.
A device is connected to, or removed from, any port.Blinking rapidly
Blinking for 2 mins
Status Light Description
* Images may dier from actual products.
Flip to the next page to continue with the setup.
4
Turn o your modem, cable the modem to the router’s WAN port.
1
Turn on the modem and wait 2 minutes for it to restart.
Connect the power adapter to the router and turn it on.
2
3
Install Your Router
If your Internet comes from an Ethernet outlet, please connect the router’s WAN port to it, and then follow Step 3 and Part 2: Two Methods to Setup.
If you want to configure this router as an access point(similar to a WiFi extender) to extend the existing network, please refer to the Access Point
Mode section on the next page.
Scan the QR code to
get the video guide.
Customer Service
Servicio al Cliente
Kundendienst
顧客サービス
Scan the QR code,
get Video Setup and more support.
クイックスタートガイド
Guide de démarrage rapide
Schnellstartanleitung
Guida Rapida
www.speedefy.com/help [e-mail]
(1)
(2)
Can Not Connect to WiFi 6 Router Wirelessly?
Some older versions of driver or software for wireless devices may be incompatible with the WiFi 6 router. If you are
experiencing problems connecting to the WiFi 6 router, please update the driver or software for your wireless devices.
How to update the driver?
Check the model for your wireless adapter.
Go to the manufacture’s website for the latest driver version.
(3)
Update the driver. You can also contact the adapter manufacture for further assistance in updating.
Ways to Reset the Router
With the router powered on, press and hold the WPS/RST buon on the back until the Power LED starts blinking.
Log in to the web management page of the router, go to Administration>Device Management, and click Reset.
Go to Speedy WiFi App. On the Tools page, click Reset. The router will reset automatically.
Q1: What connection type to choose if the router failed to detect automatically?
Q2: Why cannot I access the Internet after installing the router?
FAQ
Description
Obtain IP address from ISP automatically. If your ISP does not provide
username and password, choose DHCP to connect.
Ask configurations from your ISP if you are using a static IP.
Applicable to use if your ISP provided a PPPoE username and password.
Type
PPPoE
DHCP
Static IP
For more questions and answers, please visit www.speedefy.com/faq
Try connecting a computer directly to the modem via an Ethernet cable, then check if you have Internet access.
If not, contact your ISP.
Check if the router’s WAN port is connected to the modem properly, and confirm the indicator’s status.
If your wired devices cannot access the Internet:
2) Make sure your PC is set to obtain an IP address automatically and obtain DNS server address automatically.
1 ) Confirm if your PC is connected to a LAN port properly.
If your WiFi-enabled devices cannot access the Internet:
1) Reboot the router and reconnect to the WiFi. If it doesn’t work, factory reset the router and repeat the router
setup process.
Q3: Why cannot I access the web management page?
If the computer is set to a static IP address, change it to obtain an IP address automatically.
Disable the proxy server, if enabled. Also, disable the VPN software.
Disable and re-enable the network adapter being used on your computer.
Q4: How to register an account in Speedy WiFi APP?
Q5: Why my download speed cannot reach the advertised speed rate?
Ensure that hp://speedefywifi.com is correctly entered in the web browser. Alternatively, visit 192.168.3.1
Use another web browser and try again.
Reboot your router and try again.
It is recommended to sign in with a Third-Party login such as Gmail or Apple ID(if using an iOS device).
If you want to register with an email account:
1) Enter your email account and password and click Register.
2) An activation email will be sent to the mailbox. Remember to click the activation link in the email.
PS: 1. Try to use a common browser such as Chrome, Edge, Firefox, and Safari to open the link.
2. Check the JUNK MAIL of the mailbox if you can not find the activation email.
Check the Internet speed and link quality from your ISP. If the Internet is 100Mbps, you can get up to 12.5MBps
download speed. (1 Byte=8 bits) Actual speeds may vary due to transmission loss.
Place the router in a central location instead of the corner to improve wireless performance. All antennas should
be upright.
Devices under 2.4G WiFi will get a lower speed than 5G WiFi. Also, the wired connection will deliver a higher
speed than a wireless connection.
Check if there are multiple users sharing the connection at the same time. Try to limit their speed, or if required,
even block them in the web management page or Speedy WiFi App.
Try to connect the gigabit port of the modem to the router using a cat5e Ethernet cable, or beer.
Note: If you fail to register, try to use a common email such as Outlook, Gmail or Yahoo and try again.
AP (Access Point) Mode
In this mode, the Speedefy router can work as a WiFi extender to turn a wired network into a wireless network,
extending the WiFi range.
(1)
(2)
(3)
(4)
Connect a computer to the Speedefy router.
Use an Ethernet cable, or wirelessly by joining the default SSID printed on the label.
Connect the existing router to the Speedefy Router.
Cable Speedefy router’s WAN or LAN port to your existing router’s Ethernet port, as shown above.
Log in to the Speedefy router.
Visit hp://speedefywifi.com in a browser. Complete the instructions if this is the first time you're seing
up the router.
Enable AP Mode.
Go to Internet Seings, select AP, and click Save.
Wait for the router to reboot. It will complete the AP
Mode setup automatically.
Caution!
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Operating frequency: 2412-2462MHz, 5150-5250MHz, 5725-5850MHz
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can
determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules.
This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmier must be installed
to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or
transmier. End-users and installers must be provided with antenna installation instructions and consider removing the no-collocation statement.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
CE Mark Warning
Declaration of Conformity
This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take
adequate measures. Operations in the 5.15-5.25GHz band are restricted to indoor use only. This equipment should be installed and operated with
minimum distance 20cm between the device and your body.
NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. (2) To avoid
unnecessary radiation interference, it is recommended to use a shielded RJ45 cable.
WARNING: The mains plug is used as disconnect device, the disconnect device shall remain readily operable.
Hereby, SHENZHEN TENO NETWORK TECHNOLOGIES CO., LTD. declares that the radio equipment type KX450 is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address: hps://www.speedefy.com/regulations-ce/
Operating Frequency:
2.4 GHz: EU/2400-2483.5MHz (CH1-CH13)
5 GHz: EU/5150-5250MHz (CH36-CH48)
EIRP Power (Max.):
2.4 GHz: 19.86 dBm
5 GHz: 22.96 dBm
Software Version: V16.03.15.XX
Caution: (KX450)
Adapter Model: BN074-A18012U/ BN074-A18012B/ BN074-A18012E
Manufacture: SHENZHEN HEWEISHUN NETWORK TECHNOLOGY CO., LTD.
Input: 100 - 240V AC, 50/60Hz, 0.6A
Output: 12V 1.5A
: DC Voltage
RECYCLING
This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled
pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment.
User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.
Operating Temperature: 0°C - 40°C
Operating Humidity: (10% - 90%) RH, non-condensing
2 4IPTV/3WPSReset WANPOWER 1
Connect the included AC power adapter.
Connect an Ethernet cable to this port, and to a
broadband Internet cable/DSL or fiber modem.
Connect Ethernet cables to these ports, and to
wired devices on your network.
WPS: Press it to connect to the WPS-enabled
network devices.
Reset: Use a sharp object to press it for 8
seconds to factory reset your router.
Power Port
Reset
WPS
WAN Port
LAN Ports
( 1, 2, 3,4 )
Router
Modem
Power Adapter
Modem
Power Buon
Power Adapter
WAN
Power
Internet
DSL or
Cable
Ethernet
Cable
4WPSReset WAN 1 2 IPTV/3POWER
WAN