Use and Care Manual

Architectural Coatings Speedhide Interior/Exterior Masonry Hi Fill Latex Block Filler
GENERAL DESCRIPTION
PRODUCT DATA
SPEEDHIDE
®
6-15XI
RECOMMENDED SUBSTRATES
FEATURES / BENEFITS
Speedhide block filler is formulated to meet the performance
requirements of professional applicators. This one component
acrylic latex block filler provides excellent filling properties on
interior and exterior bare porous surfaces of light-weight concrete
or cinder block as well as cured concrete and masonry.
Concrete/Masonry Block
Masonry
Stucco
PRODUCT TYPE: Vinyl Acrylic
SHEEN: Flat
VOLUME SOLIDS: 50% +/- 2%
WEIGHT SOLIDS: 70% +/- 2%
VOC: <50 g/L (0.4 lbs./gal.)
WEIGHT/GALLON: 14 lbs. (6.4 kg) +/- 0.2 lbs. (91 g)
COVERAGE: Approximately 100 sq. ft./gal. (37.2 sq. m/3.78L) per
U.S. Gallon (3.78L) on smooth, nonporous surfaces.
Wet Film Thickness: 16 mils
Wet Microns: 406
Dry Film Thickness: 8 mils
Dry Microns: 203
Coverage figures do not include loss due to surface irregularities and
porosity or material loss due to application method or mixing.
DRYING TIME: Dry time @77ºF (25ºC); 50% relative humidity.
To Touch: 1 hour
To Recoat: 18 hours with water-based coatings
48 hours with solvent-based coatings
To Full Cure: 30 days
Drying times listed may vary depending on temperature, humidity, film
build, color, and air movement.
CLEANUP: Clean tools with warm, soapy water.
DISPOSAL: Contact your local environmental regulatory agency for
guidance on disposal of unused product. Do not pour down a drain or
storm sewer.
FLASH POINT: Over 200ºF (93ºC)
TINTING AND BASE INFORMATION
Refer to the appropriate color formula book, automatic tinting
equipment, and or computer color matching system for color formulas
and tinting instructions.
6-15XI White
Colors can be approximated by using the section and % listed in the
Voice of Color Formula Book index. Computer Color Matching system
or Autotinter. Do not use colorants G, J, M, V and Z.
Some colors, drastic color changes, or porous substrates may require
more than one coat to achieve a uniform finish.
Features Benefits
Excellent filling properties Provides smooth surface for subsequent priming and topcoating
Good adhesion Minimizes peeling and cracking
Easy application Easy to apply and provide sheen uniformity
Low VOC, <50g/L Meets the most stringent VOC regulations nationwide
MPI #4 approval Meets strict performance and aesthetic requirements
CONFORMANCE STANDARDS
Can help earn LEED v4 points in the EQ Low-Emitting
Materials Credit and the MR Building Product Disclosure and
Optimization – Environmental Product Declarations Credit
VOC compliant in all regulated areas
MPI approval in category #4
LIMITATIONS OF USE
Apply when air, surface and product temperatures are above 50ºF
(10ºC) and at least 5º F (3ºC) above the dew point. For exterior
application avoid applying late in the day when dew or
condensation are likely to form or if rain is anticipated.
Not recommended for immersion service or use below grade, or
where the concrete block to be coated rests directly on an
underground footer or slab in direct contact with the earth, or
where moisture might penetrate the block and get behind the
block filler to cause a coating failure.
Do not apply over silicone-type water repellents. Exterior
applications must be topcoated.
PROTECT FROM FREEZING
Read Label and Safety Data Sheet Prior to Use. See other cautions on last page.
5-Gallon (18.9 L)
PACKAGING