Use and Care Manual

Architectural Coatings PPG SPEEDHIDE Interior MaxPrime™ Latex Primer/Surfacer
GENERAL DESCRIPTION
PRODUCT DATA
SPEEDHIDE
®
6-4
RECOMMENDED SUBSTRATES
FEATURES / BENEFITS
Our best professional high build interior latex primer formulated to
meet the performance requirements of professional applicators.
SPEEDHIDE Interior MaxPrime Latex Primer/Surfacer ensures
the finish will be a smooth and uniform sheen by minimizing the
differences in both porosity and texture between drywall paper
and joints.It also minimizes drywall imperfections such as minor
sanding grooves, pinholes, and nicks. Recommended for use on
properly prepared interior gypsum wallboard-drywall.
Gypsum Wallboard-Drywall
PRODUCT TYPE: Vinyl Acrylic Latex
SHEEN: Flat
VOLUME SOLIDS: 26% +/- 2%
WEIGHT SOLIDS: 44% +/- 2%
VOC: <50 g/L (0.4 lbs./gal.)
WEIGHT/GALLON: 11.0 lbs. (5.0 kg) +/- 0.2 lbs. (91 g)
COVERAGE: Approximately 400 sq. ft./gal. (37 sq. m/3.78L) per U.S.
Gallon (3.78L) on smooth, nonporous surfaces.
Wet Film Thickness: 4.0 mils
Wet Microns: 101.6
Dry Film Thickness: 1.0 mils
Dry Microns: 25.4
Coverage figures do not include loss due to surface irregularities and
porosity or material loss due to application method or mixing.
DRYING TIME: Dry time @ 77ºF (25ºC); 50% relative humidity.
To Touch: 30 minutes
To Recoat: 1 hour
Drying times listed may vary depending on temperature, humidity, film
build, color, and air movement.
CLEANUP: Clean tools with warm soapy water
DISPOSAL: Contact your local environmental regulatory agency for
guidance on disposal of unused product. Do not pour down a drain or
storm sewer.
FLASH POINT: Over 200ºF (93ºC)
TINTING AND BASE INFORMATION
Refer to the appropriate color formula book, automatic tinting
equipment, and or computer color matching system for color formulas
and tinting instructions.
6-4 White
A1.17
Features Benefits
Provides a uniform base Eliminates flat and shiny spots
Great hiding Hides minor surface imperfections
User friendly Broad application utility
Fast drying Saves time with quick recoat
Easy to sand Saves labor
Easy soap and water clean up No solvent disposal issues
Can help earn LEED 2009 credits Contributes to sustainable design
APPLICATION INFORMATION
Stir thoroughly. When using more than one can of the same color,
intermix to ensure color uniformity. USE WITH ADEQUATE
VENTILATION. KEEP OUT OF REACH OF CHILDREN. Read all
label and Material Safety Data Sheet (MSDS) information prior to
use. MSDS are available through our website or by calling
1-800-441-9695.
Application Equipment: Apply with a high quality brush, roller,
paint pad, or by airless spray equipment. Where necessary,
apply a second coat.
Airless Spray: Pressure 2000 psi, tip 0.015” - 0.021”
Spray equipment must be handled with due care and in
accordance with manufacturer’s recommendation. High-pressure
injection of coatings into the skin by airless equipment may cause
serious injury.
Brush: Polyester/Nylon Brush
Roller: 3/8” - 3/4” nap roller cover
Thinning: Thinning is not usually required. If necessary, thin with
up to 1/4 pint (118mL) of water per U.S. gallon (3.78 L) of paint.
Permissible temperatures during application:
Material: 50 to 90ºF 10 to 32ºC
Ambient: 50 to 100ºF 10 to 38ºC
Substrate: 50 to 100ºF 10 to 38ºC
CONFORMANCE STANDARDS
VOC compliant in all regulated areas
Can help earn LEED
®
2009 credits