Instructions / Assembly

ManualsBrandsSpeedi-Products ManualsHeating, Ventilation, and Air Conditioning5 in. B-Vent 90-Degree Round Adjustable Elbow

Installation

Instructions

Type “B” Gas Vent

Model E/R 3" – 8"

ECCO TYPE “B” GAS VENT AND ACCESSORIES

ARE FOR USE ONLY WITH LISTED CATEGORY 1

GASFIRED APPLIANCES OR APPLIANCES

LISTED FOR USE WITH TYPE “B” GAS VENT.

TEMPERATURE AT THE OUTLET OF THE

APPLIANCE SHALL NOT EXCEED 245°C 470°F.

ECCO Type B Gas Vent and accessories are for venting

listed Natural Gas or Liquid Propane Category 1

appliances only. ECCO Type B Gas Vent Systems may be

used on other gas-burning appliances, providing the

appliance is certified for use with Type B Gas Vent, the

installation conforms to the appliance manufacturer’s

certified installation instructions, and the installation is

acceptable to the requirements of the local authority

having jurisdiction. Type B Gas Vent shall not be used to

vent flue products from incinerators, combination gas/

oil appliances, oil-fired, or wood-burning appliances. If

there is a question about the use of Type B Gas Vents,

contact the appliance manufacturer, the authority

having jurisdiction, or ECCO Manufacturing™ for further

information.

www.eccomfg.com

MH-12111

Vent sizing and installation are to be made in accordance with the

applicable codes shown below.

In USA

Connection to appliance and vent sizing to be

in accordance with the NATURAL FUEL GAS

CODE, ANSI Z223.1 (NFPA 54), NFPA 211, GAMA

VENTING TABLES, and/or the requirements of the

local authorities having jurisdiction.

In Canada

Connection to appliance and vent sizing to

be in accordance with the NATURAL GAS

INSTALLATION CODE, CAN/CGA-B149.1 or

the PROPANE INSTALLATION CODE,

CAN/CGA-B149.2, and/or the requirements

of the local authorities having jurisdiction.

Tested to UL441 “Gas Vent” basic standard.

Summary of content (8 pages)

PAGE 1
Installation Instructions Type “B” Gas Vent Model E/R 3" – 8" ECCO TYPE “B” GAS VENT AND ACCESSORIES ARE FOR USE ONLY WITH LISTED CATEGORY 1 GAS-FIRED APPLIANCES OR APPLIANCES LISTED FOR USE WITH TYPE “B” GAS VENT. TEMPERATURE AT THE OUTLET OF THE APPLIANCE SHALL NOT EXCEED 245°C (470°F). In Canada Connection to appliance and vent sizing to be in accordance with the NATURAL GAS INSTALLATION CODE, CAN/CGA-B149.1 or the PROPANE INSTALLATION CODE, CAN/CGA-B149.
PAGE 2
Figure 1 Read through all of these instructions before beginning your installation. Failure to install as described in these instructions will void the manufacturer’s warranty and may have an effect on insurance and UL listing. Keep these instructions for future reference. RAINCAP (HIGH WIND) See Table 1 General Type B Gas Vents are for venting listed Natural Gas or Liquid Propane Category I appliances only.
PAGE 3
Table 1 Roof Pitch Flat to 7/12 Over 7/12 to 8/12 Over 8/12 to 9/12 Over 9/12 to 10/12 Over 10/12 to 11/12 Over 11/12 to 12/12 Over 12/12 to 14/12 Over 14/12 to 16/12 Over 16/12 to 18/12 Over 18/12 to 20/12 Over 20/12 to 21/12 Min. Height from Roof to Lowest Discharge Opening (Ft.) 1.0 1.5 2.0 2.5 3.25 4.0 5.0 6.0 7.0 7.5 8.0 Figure 2 11) Rain Caps Rain caps may be susceptible to blockage through freezing moisture in areas of low ambient temperature. Consult authority having jurisdiction.
PAGE 4
) Pipe Assembly Sections of ECCO B-Vent round pipe are joined together in the following ways: Figure 3 • Sizes 3", 4", 5" – Align the seams, slide the upper vent over the lower vent and rotate the upper vent 1/4 turn to the left. • Sizes 6", 7", 8" – Align the seams, slide the upper vent over the lower vent and snap the lock into place. • Correctly assembled pipes will have the bottom end of the vent meeting the step of the adjoining vent.
PAGE 5
Installation with White Metal Products Inc. and Metal-Fab Oval B-Vent (USA only) Figure 2A Figure 2B • When connecting ECCO Round B-Vent to White Metal Products/Metal Fab Oval B-Vent (as shown in Figure 2A and 2B), assemble the components together and secure with (2) #8 × 1/4" sheet metal screws. • Care must be taken not to pierce or damage the inner flue gas conduit. Check the connection to ensure that the inner conduit is not damaged and that the joint is gas tight and safe for use.
PAGE 6
Finish Collar Type “B” Gas Vent Installation Model E/R 3" – 8" Support Ring Rain Cap Storm Collar Available: Standard Spun (optional) Aluminum Tee Reducer w/Tabs Support Plate Roof Flashing Available: 1/12 – 7/12 Pitch 8/12 – 12/12 Pitch Flat Flashing All available soldered (optional) B-Vent to B-Vent Adaptor Hanger Strap Support Assembly 3", 4", and 5" Sizes To join vent pipes: align the seams, slide the upper vent over the lower vent, and rotate the upper vent 1/4 turn to the left Hanger Provisi
PAGE 7
Gas Vent, Type B — Limited Lifetime Warranty This limited LIFETIME warranty is granted by ECCO Manufacturing™, a division of ECCO Heating Products Ltd. 19860 Fraser Highway Langley B.C. Canada V3A 4C9 (Hereinafter referred to as “Warrantor”). IN NO EVENT WILL WARRANTOR BE LIABLE TO YOU OR ANY OTHER PERSON FOR ANY DAMAGES, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES.
PAGE 8
19860 Fraser Highway Langley, BC V3A 4C9 Phone: 604-530-4151 Fax: 604-530-1133 Toll Free: 1-877-955-4805 #21 – 11150 38th Street, S.E. Calgary, AB T2C 2Z6 Phone: 403-720-0895 Fax: 403-720-0897 Toll Free: 1-877-955-4815 www.eccomfg.com 20001 87th Avenue S.