Full Product Manual

ManualsBrandsSPEEDWAY ManualsTools & Hardware3000 lb. 12-Volt Capacity Electric Wench

*Actual product may vary slightly

Please carefully read and save these instructions before attempting to assemble, maintain, install, or operate this product.

Observe all safety information to protect yourself and others. Failure to observe the instructions may result in property

damage and/or personal injury. Please keep instructions for future reference.

For warranty purchases, please keep your dated proof of purchase. File or attach to the manual for safe keeping.

For Customer Service, Call 1-800-348-5004

or e-mail feedback@natitools.com

07253 08/2016

This product contains or, when used, produces a chemical

known to the State of California to cause cancer and birth

defects or other reproductive harm.

(California Health & Safety Code § 25249.5, et seq.)

WARNING

3,000 LB 12 VOLT WINCH

WITH ROLLER FAIRLEAD

Summary of content (10 pages)

PAGE 1
3,000 LB 12 VOLT WINCH WITH ROLLER FAIRLEAD WARNING This product contains or, when used, produces a chemical known to the State of California to cause cancer and birth defects or other reproductive harm. (California Health & Safety Code § 25249.5, et seq.) *Actual product may vary slightly Please carefully read and save these instructions before attempting to assemble, maintain, install, or operate this product. Observe all safety information to protect yourself and others.
PAGE 2
GENERAL SAFETY PRECAUTIONS WARNING: FAILURE TO READ AND FOLLOW THE SAFETY INSTRUCTIONS IN THIS OWNER’S MANUAL BEFORE INSTALLING OR USING YOUR ELECTRIC WINCH COULD RESULT IN DAMAGE TO YOUR WINCH AND SERIOUS OR FATAL INJURY!! Check all safety and environmental conditions prior and during use. Before use, ensure that you are familiar with all winching performance and operation such as speed & direction.
PAGE 3
GENERAL SAFETY PRECAUTIONS CAUTION CUT AND BURN HAZARD To avoid injury to hands and fingers: • Always wear heavy leather gloves when handling a wire rope. • Never let wire rope slip through your hands. • Always be aware of possible hot surface at winch motor, drum or wire rope during or after winch use. CAUTION MOVING PARTS ENTANGLEMENT HAZARD Moving Parts Entanglement Hazard Failure to observe these instructions could lead to minor to moderate injury. • Never apply load to hook tip or latch.
PAGE 4
WINCH & ROLLER FAIRLEAD MOUNTING 1. It is very important that the winch shall be mounted on a flat hard surface in order to make sure the motor, drum and gearbox housing are aligned correctly. 2. If a different mounting plate is used, the thickness shall be 5 mm (3/16”). If different hardware is used, it must be grade 8 minimum. 3. Four (4) included M8x 25L Grade 8.
PAGE 5
HANDLEBAR REMOTE CONTROL MOUNTING Handlebar mounted trigger switch can be operated without removing your hand from the grip. • It is recommended that the switch be installed on the left handlebar. A piece of electrical tape around the handlebar will help prevent rotation of mount on the handle bar. • Do NOT tighten over any hoses or cables. OPERATION CABLE IN AND OUT 1). To determine “ Cable Out “, turn to the “Out” position 2). To determine “ Cable In “, turn to the “In” position 3).
PAGE 6
FREESPOOL FUNTION The freespool allows rapid pay-out of the wire rope for hooking onto a load or anchor points and is operated by a freespool shifter located on the end of the winch. 1). To engage the freespool, turn the freespool shifter counter-clockwise to the “Engaged” position. The winch is now ready for pulling. 2). To disengage the freespool, turn the freespool shifter clockwise to the “Disengaged” position. Wire rope can now be free spooled off the drum.
PAGE 7
). It is very important that the winch shall be mounted on a flat surface, with the wire rope feeding form the bottom of the drum. 8). To rewind wire rope on the drum correctly , it is necessary to keep a slight load on the wire rope while cable in. LUBRICATION All moving parts in the winch are permanently lubricated at the time of assembly. Under normal conditions factory lubrication will suffice. If re-lubrication is necessary after repair or disassembly use a marine type grease.
PAGE 8
TROUBLE SHOOTING When the winch fails to operate after several attempts, or if there is any fault operation while winching, check followings.
PAGE 9
PARTS LIST & ASSEMBLY DIAGRAM Part Description Quantity Part Description Quantity 1 Motor Cover 1 13 Drum 1 2 Motor Shell 1 14 Plastic Plate 1 3 Rotor 1 15 Triangle Plate 1 4 Bear ing 1 16 Base 1 5 Motor Base 1 17 Clutch 1 6 Planetary Gear 1 18 Steel Cable 1 7 Static Ring Gear 1 19 Mounting Plate 1 8 Plastic Plate 1 20 Roller Fairlead 1 9 Tie Rod 2 21 Hook 1 10 Shaft 1 22 Strap 1 11 Spine 1 23 Handlebar Remote 1 12 Spring 1 24 Cont
PAGE 10
Limited Manufacturer Warranty North American Tool Industries (NATI) makes every effort to ensure that this product meets high quality and durability standards. NATI warrants to the original retail consumer a 1-year limited warranty from the date the product was purchased at retail and each product is free from defects in materials. Warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents, repairs or alterations, or a lack of maintenance.