F405 V3 0x30 3 A 0 BLS 5 Contents (Click on any section to jump) Part 1 - OverView Specs Overview Dimensions Package FC & ESC Connection Part 2 - SpeedyBee F405 V3 Flight Controller Layout FC’s Peripheral Connection App & FC Configuration FC Firmware Update Specifications Part 3 - SpeedyBee BLS 50A 4-in-1 ESC Layout Connection with Motors & Power Cable ESC Configuration ESC Firmware Update Specifications 1 2 3 4 5 6 7 8 9 10 11 12 13 14 F405 V3 BLS 50A 30x30 Stack User Manual V1.
Part 1 - OverView Specs Overview 1/14 Product Name SpeedyBee F405 V3 BLS 50A 30x30 Stack Flight Controller SpeedyBee F405 V3 ESC SpeedyBee BLS 50A 4-in-1 ESC Bluetooth Supported. For FC & ESC parameter settings Wireless FC Firmware Flashing NOT Supported Wireless Blackbox Dwonload & Analysis NOT Supported Power Input 3-6S LiPo Mounting 30.5 x 30.5mm(4mm hole size ) Dimension 45.6mm(L) x 44mm(W) x 18.3mm(H) Weight 23.
Dimensions 2/14 4mm 7.8mm 30.5mm 1.6mm 44mm 6.1mm 30.5mm 45.6mm 39.4mm 41.6mm 1.6mm 4mm 16.
3/14 Package Option 1 - SpeedyBee F405 V3 50A 30x30 Stack 1 3 9 11 4 5 6 2 10 7 8 1 SpeedyBee F405 V3 Flight Controller x 1 2 SpeedyBee BLS 50A 4-in-1 ESC x 1 3 35V 1500uF Low ESR Capacitor x 1 4 M3 Nylon Nut x 5 5 M3 silicone O Ring x 5 6 M3*8mm Silicone Grommets(for FC) x 5 7 M3*8.1mm Silicone Grommets(for ESC) x 5 8 SH 1.
FC & ESC Connection 4/14 Use the 8-pin cable in the package to connect the FC and the ESC. Or solder 8 wires directly to the 8 pads on each end. Method 1 - Using 8-pin cable Use any end of the 8-pin JST cable to connect the FC to the ESC. F7 V3 Flight Controller BL32 50A 4-in-1 ESC Method 2 - Direct soldering Solder 8 wires to the 8 pads on each end referring to the pad definition below.
Part 2 - F405 V3 Flight Controller Layout 5/14 FPV Cam For Second 4-in-1 ESC Receiver Extra PWM output MCU: F405 Antenna Bluetooth Chip USB TYPC-C Port Orange LED 4-level LED battery indicator Red LED Blue LED BOOT Button Green LED OSD Chip(AT7456E) Gyro(BMI270) Buzzer Betaflight LED GPS&Compass VTX(Analog/DJI) 8pin Connector(to ESC) LED1 LED4 TVS Diode (Anti-volatge spike) 5V 2A BEC SD Card Slot (Use SDSC/SDHC cards, format to 'FAT32' format) 9V 2A BEC LED3 LED2 DJI Air Unit Connector
FC’s Peripheral Connection 6/14 PPM Receiver Model: Phoenix 2 2 Model: Phoenix Joshua Edition 5-36V GND Video 5-36V GND Video GND G/TX M/RX Menu Menu Reciever PPM PPM 5V G SBUS 5V GND CH2 CH1 5V Crossfire Nano Rx 5V T2 SBUS 5V R2 GND CAM CC 5V LED DIN GND GND CH2 RX CH1 TX 5V GND G S9 SIGNAL SERVO 5V G SBUS G 5V GND LED LED Strip Buzzer BZ+ BZ- R1 VTX T1 DIN 9V G LED LED DIN 4V5 R6 RX T6 5V GND VIDEO IRC SDA PGND G SDA 3.
App & FC Configuration 7/14 Get the SpeedyBee App Search ‘SpeedyBee’ on Google Play or App Store. Or download the Android .apk file on our website: https://www.speedybee.com/download.
FC Firmware Update 8/14 SpeedyBee F405 V3 flight controller does not support wireless firmware flashing, so please flash firmware for it on your PC following the steps below: ① Connect the flight controller to the PC with a USB cable ② Open Betafight/Emuflight/INAV configurator on your PC. Take Betaflight configurator as an example, go to the ‘Firmware Flashing’ page, choose the target ‘SPEEDYBEEF405V3’ and flash.
Specifications 9/14 Product Name SpeedyBee F405 V3 30x30 Flight Controller MCU STM32F405 IMU(Gyro) BMI270 USB Port Type Type-C Barometer Built-in OSD Chip AT7456E chip BLE Bluetooth Supported. Used for Flight Controller configuration DJI Air Unit Connection Way Two ways supported: 6-pin connector or direct soldering. Supported. Please use ≤4GB SDSC/SDHC microSD card and should be formatted to Blackbox MicroSD Card Slot FAT16/FAT32 format. Don't use SDXC cards.
Part 3 - SpeedyBee BLS 50A 4-in-1 ESC Layout 10/14 Driver chips MOTOR 4 MOTOR 2 MOTOR 3 MOTOR 1 Capacitor pin hole(GND) BAT- BAT+ Capacitor pin hole(BAT+) 8pin connector(to FC) MCU(BB21) TVS Diode
Connection with Motors & Power Cable 11/14 Motor 4 Motor 2 Motor 3 Motor 1 XT60 Power Cable 1500uF Low ESR Capacitor Note: In order to prevent the stack from being burnt out by voltage spikes on powering up, it is strongly recommended to use the Low ESR capacitor in the package.
ESC Configuration 12/14 1 3 2 If you’d like to use a PC configurator, we recommend the ESC Configurator.
ESC Firmware Update We recommend using the ESC Configurator on your PC to update firmware for this ESC. Please make sure to select ‘JH-50’ as the ESC type for either BLHeli_S or Bluejay.
Specifications 14/14 Product Name SpeedyBee BLS 50A 30x30 4-in-1 ESC Firmware BLHeli_S JH50 Wireless Configuration Full Configuration Supported in the SpeedyBee app PC Configurator Download Link https://esc-configurator.com/ Continuous Current 50A * 4 Burst Current 55A(5S) TVS Protective diode Yes External Capacitor 1500uF Low ESR Capacitor(In the package) ESC Protocol DSHOT300/600 Power Input 3-6S LiPo Power Output VBAT Current Sensor Support (Scale=386 Offset=0) Mounting 30.