Telemetry Specs - (Developer Guidelines)

Specification for Spektrum X-Bus Telemetry Sensors
Page 19 Rev L
HORNET_ECU_STATE_STEADY = 0x41,
HORNET_ECU_STATE_WAIT_ACC = 0x42,
HORNET_ECU_STATE_ERROR = 0x43,
// undefined states 0x44-0x4F
XICOY_ECU_STATE_Temp_High = 0x50,
XICOY_ECU_STATE_Trim_Low = 0x51,
XICOY_ECU_STATE_Set_Idle = 0x52,
XICOY_ECU_STATE_Ready = 0x53,
XICOY_ECU_STATE_Ignition = 0x54,
XICOY_ECU_STATE_Fuel_Ramp = 0x55,
XICOY_ECU_STATE_Glow_Test = 0x56,
XICOY_ECU_STATE_Running = 0x57,
XICOY_ECU_STATE_Stop = 0x58,
XICOY_ECU_STATE_Flameout = 0x59,
XICOY_ECU_STATE_Speed_Low = 0x5A,
XICOY_ECU_STATE_Cooling = 0x5B,
XICOY_ECU_STATE_Igniter_Bad = 0x5C,
XICOY_ECU_STATE_Starter_F = 0x5D,
XICOY_ECU_STATE_Weak_Fuel = 0x5E,
XICOY_ECU_STATE_Start_On = 0x5F,
XICOY_ECU_STATE_Pre_Heat = 0x60,
XICOY_ECU_STATE_Battery = 0x61,
XICOY_ECU_STATE_Time_Out = 0x62,
XICOY_ECU_STATE_Overload = 0x63,
XICOY_ECU_STATE_Igniter_Fail = 0x64,
XICOY_ECU_STATE_Burner_On = 0x65,
XICOY_ECU_STATE_Starting = 0x66,
XICOY_ECU_STATE_SwitchOver = 0x67,
XICOY_ECU_STATE_Cal_Pump = 0x68,
XICOY_ECU_STATE_Pump_Limit = 0x69,
XICOY_ECU_STATE_No_Engine = 0x6A,
XICOY_ECU_STATE_Pwr_Boost = 0x6B,
XICOY_ECU_STATE_Run_Idle = 0x6C,
XICOY_ECU_STATE_Run_Max = 0x6D,
TURBINE_ECU_MAX_STATE = 0x74
};
enum JETCAT_ECU_OFF_CONDITIONS { // ECU off conditions. Valid only when the
ECUStatus = JETCAT_ECU_STATE_OFF
JETCAT_ECU_OFF_No_Off_Condition_defined = 0,
JETCAT_ECU_OFF_Shut_down_via_RC,
JETCAT_ECU_OFF_Overtemperature,
JETCAT_ECU_OFF_Ignition_timeout,
JETCAT_ECU_OFF_Acceleration_time_out,
JETCAT_ECU_OFF_Acceleration_too_slow,
JETCAT_ECU_OFF_Over_RPM,
JETCAT_ECU_OFF_Low_Rpm_Off,
JETCAT_ECU_OFF_Low_Battery,
JETCAT_ECU_OFF_Auto_Off,
JETCAT_ECU_OFF_Low_temperature_Off,
JETCAT_ECU_OFF_Hi_Temp_Off,
JETCAT_ECU_OFF_Glow_Plug_defective,
JETCAT_ECU_OFF_Watch_Dog_Timer,
JETCAT_ECU_OFF_Fail_Safe_Off,
JETCAT_ECU_OFF_Manual_Off, // (via GSU)
JETCAT_ECU_OFF_Power_fail, // (Battery fail)
JETCAT_ECU_OFF_Temp_Sensor_fail, // (only during startup)
JETCAT_ECU_OFF_Fuel_fail,
JETCAT_ECU_OFF_Prop_fail,
JETCAT_ECU_OFF_2nd_Engine_fail,
JETCAT_ECU_OFF_2nd_Engine_Diff_Too_High,
JETCAT_ECU_OFF_2nd_Engine_No_Comm,
JETCAT_ECU_MAX_OFF_COND
};
typedef struct
{
UINT8 identifier; // Source device = 0x19
UINT8 sID; // Secondary ID
UINT16 FuelFlowRateMLMin; // (BCD) mL per Minute