Instruction Manual

ManualsBrandsSper Scientific ManualsMeasuring instruments800002 Infrared IR Thermometer

SPECIFICATIONS

Accuracy 10°C to 150°C-2% of

reading or 2°C, whichever

is greater*

Resolution 1°C 10 to 150°C

1°F 50 to 302°F

0.1°C 10.0 to 110.0°C

0.1°F 50.0 to 230.0°F

Emissivity Setting 0.10 to 0.95 with a factory

preset of 0.95

Temperature

Sensor

Thermocouple pie

Measurement

Wavelength

Region

6 to 12 micrometers

Distance Factor D/S: Approx. 10:1

D=Distance, S=Size of

spot

Sampling Time Approx. 1 second

Data Output RS232 PC Serial Interface

Operating

Temperature

0 to 50°C (32 to 122°F)

Operating

Humidity

Less than 80% RH

Power Supply 9v Battery (included)

Power Current Approx. DC 4.8 mA

Dimension of

Meter

180 x 72 x 32 mm (7.1 x

2.8 x 1.3 inch)

Dimension of

Probe

31.5 mm diameter cylinder

x 170 mm

(1.25” dia. X 6.75”)

Weight 385g/13.5 oz.

Display 13 mm (0.5 inch) digit LCD

Accessories Instruction Manual,

Battery, Carrying Case

NARROW SPOT

IR THERMOMETER

800002

INSTRUCTION MANUAL

Summary of content (6 pages)

PAGE 1
SPECIFICATIONS Accuracy Resolution 10°C to 150°C-2% of reading or 2°C, whichever is greater* 1°C 10 to 150°C 1°F Emissivity Setting Temperature Sensor Measurement Wavelength Region Distance Factor 50 to 302°F 0.1°C 10.0 to 110.0°C 0.1°F 50.0 to 230.0°F 0.10 to 0.95 with a factory preset of 0.95 Thermocouple pie 6 to 12 micrometers Sampling Time D/S: Approx. 10:1 D=Distance, S=Size of spot Approx.
PAGE 2
TABLE OF CONTENTS BATTERY REPLACEMENT Features 3 Front Panel Description 4 Measurement Procedure 5 How to Hold the Probe when Measuring 6 Emissivity 7 Calculating & Adjusting Emissivity 7 Factors Affecting Measurement 8 RS232 Serial Interface 10 Battery Replacement 11 Specifications 12 WARRANTY “LBT” will appear in the upper left of the display when the battery outputs less than 6.5 to 7.5 v. You should replace the battery as soon as possible.
PAGE 3
RS232 SERIAL INTERFACE This instrument works with the Sper Scientific Intelligent Software and the RS232 serial connection to output data directly to your computer. You can also use it with other software using the RS232 output via 3.5 mm terminal (Fig1-14). The connector output is a 16 digit data stream which can be utilized by the user’s specific needs. A RS232 cable (Sper Scientific 840055) or equivalent is required to link the meter to the PC serial port. The cable must have a 3.
PAGE 4
FRONT PANEL DESCRIPTION 1. Display 2. Data HOLD Button 3. °C/°F Scale Selection Button 4. Memory RECORD Button 5. Memory RECALL Button 6. POWER Switch 7. 1° / 0.1° Resolution Selection Switch 8. Battery Compartment Cover 9. IR Probe Socket 10. Emissivity Adjustment VR 11. IR Probe Main Body 12. IR Probe Sensing Head This is especially important when the difference between the ambient temperature and the object temperature are significantly different. 3.
PAGE 5
the object with the IR probe, adjust the “Emissivity Adjust VR” (Fig.1-10) with a small flat head screwdriver until the readings match. • • Turning the VR to the left (counterclockwise) will adjust the emissivity to 0.10 to 0.94. Turn the VR all the way to the right to reset the probe to 0.95. MEASUREMENT PROCEDURE 1. Plug the IR probe plug (Fig.1-9) into the meter input socket (Fig.1-13). 2. Turn meter on using the POWER switch (Fig.1-6). 3. Choose scale using the °C/°F button (Fig.1-3).
PAGE 6
. Data Hold: During measurement, the “HOLD” button (Fig.1-2) will hold the measure value and the LCD will show “D.H.” in the upper left of display. Pressing the “HOLD” a second time will release the data hold function. 7. Data Record: The recording function displays the minimum and maximum readings. To start, press the “RECORD” button (Fig.1-4). “REC” will show in the lower left of the display. With “REC” on: • Press “RECALL”. “MAX” will show in the display with the maximum temperature value.