Spicer Drive Axles ® Illustrated Parts List Spicer® Drive Axles AXIP-0487 July 2011 FS140 Models
Table of Contents General Information........................................................................................................................................... 2 How To Use Illustrated Parts List..................................................................................................................... 2 Model Identification . ...................................................................................................................................... 3 Axle Parts Explode.
General Information General Information How To Use Illustrated Parts List Ordering Parts • This parts book is organized in sections according to parts servicing requirements. Use the Contents or page headings and colored tabs to find information. • Use this book to order parts for your Dana® Spicer® Axle. • For convenience, part numbers have been included for all pieces of the carrier assembly. Some of these parts, such as the carrier and caps, are serviced only in kits or assemblies.
Model Identification Model Identification Locating Model Designation Information • Axle Model Identification, Part Number and Serial Number are located on a tag at the axle centerline. This information will help to locate information in this book and to identify the correct parts for servicing. Drive Axles 4 5 3 Spicer® CUST. PART NO. SPEC. MODEL PART NO. SPEC. MODEL PART NO. RATIO MADE IN: 2 CUST. PART NO. SERIAL NO. 6 Spicer® SERIAL NO. RATIO 1 MADE IN: 7 Drive Axle Assembly Tag 1.
Model Identification Using Model Designation to Identify Axle Components • The Axle Model Identification number contains information that is important to understand when purchasing service parts or new components. The Model Identification number provides important vehicle, capacity and application information and model features. Use this guideline to understand your Axle Model Identification. If you need assistance, contact your Roadranger representative.
Models Models The following models are included in this publication: Single Reduction Models Model Axle Capacity Gear Size S17-140 17,000 Lbs 13.4” Hypoid S19-140 19,000 Lbs* 13.4” Hypoid *Note: Up to 19,800 lbs. GAWR for approved school bus applications.
Axle Parts Explode Axle Parts Explode 12 11 10 13 10 30 27 29 16 15 14 23 26 22 21 20 9 28 19 24 25 9 10 8 7 6 5 4 3 2 1 6 17 18
Axle Parts List Axle Parts List Item Part Name Qty KIT - BEARING 1 Pinion Nut 1 2 End Yoke & Slinger Assy 1 3 Pinion Oil Seal 1 4 Outer Pinion Bearing Cone 1 5 Outer Pinion Bearing Cup 1 6 Bearing Pre-Load Spacer 1 7 Inner Pinion Bearing Cup 1 8 Inner Pinion Bearing Cone 1 9 Ring Gear & Drive Pinion - NSS 1 10 Diff Carrier-n-Cap Assy.
Pinion Bearing Spacers Pinion Bearing Spacers Pinion Bearing Spacer Kit P/N: 504039 Part Number 130543 130545 130547 130549 130551 130553 * 130555 130557 130559 130561 130563 * 130565 * 130567 * 130569 130571 130573 * 130575 * 130577 * 130579 130581 130583 * 130585 130587 130589 130591 130593 Spacer (mm) 27.230 27.280 27.330 27.390 27.440 27.490 27.540 27.590 27.610 27.640 27.660 27.690 27.720 27.740 27.770 27.790 27.820 27.840 27.870 27.890 27.920 27.940 27.970 28.000 28.050 28.100 Thickness (in) 1.
Gear & Pinion Kits Ring Gear & Pinion Identification Dana has highly developed primary axle gearing which is only used in matched sets. These sets are identified by the mating parts listed below. Within any Dana production drive axle or genuine Spicer® Gear & Pinion service kits, these mated part numbers will appear. Because they are developed as a set with precision machining, never mix gears and pinions from different mated sets within an axle. Shortened gearing life, noise and failure may occur.
Axle Housing Parts Explode Axle Housing Parts Explode 5 6 3b 6 6 5 5 5 5 5 3a 2 5 5 5 6 6 Carrier to Housing Fasteners (Viewed from front of axle) 4 5 4 6 1 Axle Housing Parts List Item Description Qty 1 Axle Shaft - 39 Inv 2 2 Axle Housing 1 3 KIT-BREATHER VALVE ASSY 1 3a Hose & Clamp 1 3b Vent 1 KIT-AXLE HOUSING HARDWARE 4 Washer 14 5 Capscrew, Carrier to Hsg - Short 5 6 Capscrew, Carrier to Hsg - Long 9 7 Wheel Brg Nut - outer 2 8 Wheel Brg Nut - inner 2 9 Washer - Wheel Brg Loc
Axle Housings Axle Housings Axle Series Tag I.D.
Axle Shafts Axle Shafts Part No. 133963 12 Qty 2 Spline 39 Body O.D. 1.81 Shaft Length 40.118 Spline Length 4” Flange O.D. 6.625 Flange Holes 8(.
Service Carriers Service Carriers S140 Standard Carrier 13.40” (340mm) Hypoid Gearing Side Gear # 127367 Ratio 3.31 3.58 3.73 3.91 4.10 4.30 4.56 4.88 5.29 5.57 6.14 6.
Yokes & Flanges Yokes & Flanges Spicer yoke part numbers shown below are PRODUCTION part numbers and are for reference only. The part numbers needed for service may vary. Please contact Driveshaft Division for price & availability of service yokes. For additional Yoke information reference Dana Bulletin ABIB-0607. STYLE X Half Round A C B S140 Series - 39 Inv. Spline Production Yoke & Slinger 100-4-1431-1X 6-4-10321-1X 14 Series Style Dim. A Dim. B SPL100 X 4.750” 1.625” 1710 X 5.250” 1.
Oil Seal Installation Tools Oil Seal Installation Tools Oil seal installation tools are available for installing drive axle pinion seals. Using these tools ensures proper installation of the seal. Failure to use these tools may result in an improperly installed or damaged seal.
Aftermarket Group ForDana spec‘ing or service assistance, call 1.800.621.8084 or visit our website at www.spicerparts.com PO Box 321 Toledo, Ohio 43697-0321 Warehouse Distributor: Dana Commercial Vehicle1.800.621.8084 Products Group OE Technology Dealers: 1.877.777.5360 3939 Drive Maumee, Ohio, USA 43537 www.spicerparts.com www.dana.com AXIP-0487 Printed in U.S.A. Copyright Dana Limited, 2012. All rights reserved. Dana Limited.
