Service Manual D__R440, 460, 480, D_R461, 462, 463, 521, 581, 601, 651, 652, 653 Owner manual
Table Of Contents
- Warnings and Caution
- Table of Contents - Visual
- Introduction
- Failure Analysis
- Inspection
- Differential Carrier Assembly - Parts
- Forward Axle Differential Carrier Removal and Installation
- Installation of Forward Differential Carrier
- Installation of Forward Axle Housing Cover and Output Shaft Bearing Parts
- Rear Axle Differential Carrier Removal and Installation
- Rear Differential Carrier “Installation”
- Differential Lockout
- Differential Lockout Overhaul
- Original Design Lockout Overhaul
- Cylindrical Design Lockout - Overhaul
- Power Divider - Parts Exploded View
- Remove Power Divider
- Remove Power Divider from Differential Carrier (with carrier removed from axle housing)
- Disassemble, Assemble and Overhaul the Power Divider
- Disassemble Power Divider Cover (For Axles with Input Shaft Tapered Roller Bearing)
- Assemble Power Divider Cover (For Axles with Input Shaft Tapered Roller Bearing)
- Inter-axle Differential
- Output Shaft Assembly
- Install Power Divider on Differential Carrier (with carrier assembled to axle housing)
- Install Power Divider on Differential Carrier (with carrier removed from axle housing)
- Measure and Adjust Input Shaft End-Play
- Forward Axle Carrier Assembly (Single Speed) with Diff. Lock - Parts Exploded View
- Rear Axle (Single Speed) - Parts Exploded View
- Forward Axle (Two Speed) - Parts Exploded View
- Rear Axle (Two Speed) - Parts Exploded View
- Disassemble Differential Carrier (with power divider removed)
- Drive Pinion - Parts Exploded View
- Disassemble and Overhaul Drive Pinion
- Install Drive Pinion Assembly
- Install Helical Gear and Pinion Outer Support Bearing - Forward Axle Only
- Wheel Differential Assembly - Parts Exploded View
- Disassemble, Overhaul and Assemble Wheel Differential (Forward and Rear Axles)
- Planetary and 2-Speed Models (Forward and Rear Axles)
- Disassemble Dual Reduction Differential Case
- Assemble Dual Reduction Differential Case
- Install Differential-Forward and Rear Axles
- Measure and Adjust Carrier Assembly
- Wheel Differential Lock - Parts Exploded View
- Install and Adjust Wheel Differential Lock, Dual Range Shifters
- Piston Air Shift Unit
- Air Shift Unit Replacement
- Air Shift Unit Overhaul
- Housing and Rear Cover Assembly - Parts Exploded View
- Seals
- Housing Breather
- Wheel End Seal - Parts Exploded View
- Remove and Overhaul Wheel End Seal
- Wheel Adjustment Systems
- Verify Wheel End-play Procedure
- Lubricate Wheel End
- Lubrication
- Lube Change Intervals
- Change Lube
- Standpipes
- Torque Chart
- Wheel Differential Lock
- Differential Lock Theory of Operation
- Control Systems
- Dual Range Axle Shift Systems
- Troubleshooting
- Proper Vehicle Towing
- Axle Shift System Components
- Inter-Axle Differential Lockout With Interlock Control Valve (straight-air type)
- Theory of Operation
- Power Flow and Torque Distribution
- Lubrication
- Torque Distribution in Low Range
6
General Information
Ring Gear and Pinion
Note: Ring gear and drive pinion are matched parts and must
be replaced in sets.
1 - Part number
2 - Number of ring gear teeth
3 - Manufacturing numbers
4 - Matching gear set number
5 - Number of pinion teeth
6 - Date code
7 - Indicates genuine Spicer parts
8 - Heat code
41-8
SPICER
127381
OF
NL2
17
127
8-41
127428
SPICER
17
G
6-39
JD77
85405
86
5
2
3
1
7
8
L
7
0
3
8
1
4
L7038
4
7
G
3
127
0H
6
8
6