Service Manual D__R440, 460, 480, D_R461, 462, 463, 521, 581, 601, 651, 652, 653 Owner manual
Table Of Contents
- Warnings and Caution
- Table of Contents - Visual
- Introduction
- Failure Analysis
- Inspection
- Differential Carrier Assembly - Parts
- Forward Axle Differential Carrier Removal and Installation
- Installation of Forward Differential Carrier
- Installation of Forward Axle Housing Cover and Output Shaft Bearing Parts
- Rear Axle Differential Carrier Removal and Installation
- Rear Differential Carrier “Installation”
- Differential Lockout
- Differential Lockout Overhaul
- Original Design Lockout Overhaul
- Cylindrical Design Lockout - Overhaul
- Power Divider - Parts Exploded View
- Remove Power Divider
- Remove Power Divider from Differential Carrier (with carrier removed from axle housing)
- Disassemble, Assemble and Overhaul the Power Divider
- Disassemble Power Divider Cover (For Axles with Input Shaft Tapered Roller Bearing)
- Assemble Power Divider Cover (For Axles with Input Shaft Tapered Roller Bearing)
- Inter-axle Differential
- Output Shaft Assembly
- Install Power Divider on Differential Carrier (with carrier assembled to axle housing)
- Install Power Divider on Differential Carrier (with carrier removed from axle housing)
- Measure and Adjust Input Shaft End-Play
- Forward Axle Carrier Assembly (Single Speed) with Diff. Lock - Parts Exploded View
- Rear Axle (Single Speed) - Parts Exploded View
- Forward Axle (Two Speed) - Parts Exploded View
- Rear Axle (Two Speed) - Parts Exploded View
- Disassemble Differential Carrier (with power divider removed)
- Drive Pinion - Parts Exploded View
- Disassemble and Overhaul Drive Pinion
- Install Drive Pinion Assembly
- Install Helical Gear and Pinion Outer Support Bearing - Forward Axle Only
- Wheel Differential Assembly - Parts Exploded View
- Disassemble, Overhaul and Assemble Wheel Differential (Forward and Rear Axles)
- Planetary and 2-Speed Models (Forward and Rear Axles)
- Disassemble Dual Reduction Differential Case
- Assemble Dual Reduction Differential Case
- Install Differential-Forward and Rear Axles
- Measure and Adjust Carrier Assembly
- Wheel Differential Lock - Parts Exploded View
- Install and Adjust Wheel Differential Lock, Dual Range Shifters
- Piston Air Shift Unit
- Air Shift Unit Replacement
- Air Shift Unit Overhaul
- Housing and Rear Cover Assembly - Parts Exploded View
- Seals
- Housing Breather
- Wheel End Seal - Parts Exploded View
- Remove and Overhaul Wheel End Seal
- Wheel Adjustment Systems
- Verify Wheel End-play Procedure
- Lubricate Wheel End
- Lubrication
- Lube Change Intervals
- Change Lube
- Standpipes
- Torque Chart
- Wheel Differential Lock
- Differential Lock Theory of Operation
- Control Systems
- Dual Range Axle Shift Systems
- Troubleshooting
- Proper Vehicle Towing
- Axle Shift System Components
- Inter-Axle Differential Lockout With Interlock Control Valve (straight-air type)
- Theory of Operation
- Power Flow and Torque Distribution
- Lubrication
- Torque Distribution in Low Range
15
Differential Carrier Assembly
Differential Carrier
Assembl
y
Rear Axle Differential Carrier Removal and Installation
Removal of Rear Differential Carrier
Perform the following steps:
1. Block the vehicle.
2. Drain axle lubricant.
3. Disconnect air line if working on a differential lock ax-
le. (See Differential Lockout Section).
4. Disconnect inter-axle driveline.
5. Remove axle stud nuts and axle shafts (If used, re-
move lock washers and taper dowels).
The differential lock 461/521/581 models use axle shafts
with different spline length (4" or 11"). Axle shafts may also
be location specific with various wheel equipment. Do not
misplace axle shafts from their intended location.
TIP: To loosen dowels, hold a brass drift in the center of the
shaft head and strike drift with a sharp blow using a hammer.
Do not lie under carrier after fasteners are removed. Use
transmission jack to support differential carrier assembly
prior to loosening fasteners.
Do not strike the shaft head with a steel hammer. Do not use
chisels or wedges to loosen shaft or dowels.
6. Remove capscrews, nuts and lock washers.
7. Remove differential carrier assembly.
WARNING
CAUTION
1 - Carrier fasteners
2 - Carrier assembly
3 - Rear axle assembly
4 - Axle shaft
5 - Nut
6 - Lock washer
2
3
4
6
5
1