Service Manual D__R440, 460, 480, D_R461, 462, 463, 521, 581, 601, 651, 652, 653 Owner manual
Table Of Contents
- Warnings and Caution
- Table of Contents - Visual
- Introduction
- Failure Analysis
- Inspection
- Differential Carrier Assembly - Parts
- Forward Axle Differential Carrier Removal and Installation
- Installation of Forward Differential Carrier
- Installation of Forward Axle Housing Cover and Output Shaft Bearing Parts
- Rear Axle Differential Carrier Removal and Installation
- Rear Differential Carrier “Installation”
- Differential Lockout
- Differential Lockout Overhaul
- Original Design Lockout Overhaul
- Cylindrical Design Lockout - Overhaul
- Power Divider - Parts Exploded View
- Remove Power Divider
- Remove Power Divider from Differential Carrier (with carrier removed from axle housing)
- Disassemble, Assemble and Overhaul the Power Divider
- Disassemble Power Divider Cover (For Axles with Input Shaft Tapered Roller Bearing)
- Assemble Power Divider Cover (For Axles with Input Shaft Tapered Roller Bearing)
- Inter-axle Differential
- Output Shaft Assembly
- Install Power Divider on Differential Carrier (with carrier assembled to axle housing)
- Install Power Divider on Differential Carrier (with carrier removed from axle housing)
- Measure and Adjust Input Shaft End-Play
- Forward Axle Carrier Assembly (Single Speed) with Diff. Lock - Parts Exploded View
- Rear Axle (Single Speed) - Parts Exploded View
- Forward Axle (Two Speed) - Parts Exploded View
- Rear Axle (Two Speed) - Parts Exploded View
- Disassemble Differential Carrier (with power divider removed)
- Drive Pinion - Parts Exploded View
- Disassemble and Overhaul Drive Pinion
- Install Drive Pinion Assembly
- Install Helical Gear and Pinion Outer Support Bearing - Forward Axle Only
- Wheel Differential Assembly - Parts Exploded View
- Disassemble, Overhaul and Assemble Wheel Differential (Forward and Rear Axles)
- Planetary and 2-Speed Models (Forward and Rear Axles)
- Disassemble Dual Reduction Differential Case
- Assemble Dual Reduction Differential Case
- Install Differential-Forward and Rear Axles
- Measure and Adjust Carrier Assembly
- Wheel Differential Lock - Parts Exploded View
- Install and Adjust Wheel Differential Lock, Dual Range Shifters
- Piston Air Shift Unit
- Air Shift Unit Replacement
- Air Shift Unit Overhaul
- Housing and Rear Cover Assembly - Parts Exploded View
- Seals
- Housing Breather
- Wheel End Seal - Parts Exploded View
- Remove and Overhaul Wheel End Seal
- Wheel Adjustment Systems
- Verify Wheel End-play Procedure
- Lubricate Wheel End
- Lubrication
- Lube Change Intervals
- Change Lube
- Standpipes
- Torque Chart
- Wheel Differential Lock
- Differential Lock Theory of Operation
- Control Systems
- Dual Range Axle Shift Systems
- Troubleshooting
- Proper Vehicle Towing
- Axle Shift System Components
- Inter-Axle Differential Lockout With Interlock Control Valve (straight-air type)
- Theory of Operation
- Power Flow and Torque Distribution
- Lubrication
- Torque Distribution in Low Range
28
Power Divider
7. At this point in disassembly, it is desirable to remove
lube pump drive gear nut. Hold input shaft yoke to se-
cure drive gear, then loosen and remove drive gear
nut.
8. Remove input shaft nut and flat washer.
Note: Some models do not use flat washer as it is built into the
nut.
9. Remove yoke from input shaft using a puller tool.
TIP: A yoke puller tool may be made from the center
section of most gear puller tools, or may be pur-
chased from your local tool distributor.
10. Remove input bearing cage, capscrews, input bear-
ing cover and shim pack.
11. If input shaft bearing cup needs replacement, use ei-
ther of the following recommended practices:
Weld: Place a weld bead around the cup, when the
weld cools the cup will fall out.
Drill: Drill a 1/4 inch size hole through the bearing
cover to the back side of the cup and use a punch to
remove the bearing cup.
Note: Shift fork cannot be removed until lockout unit is disas-
sembled (see Differential Lockout Overhaul on page 20).
Shift fork push rod is secured to the lockout piston with
a nut.
12. Slide input shaft assembly out of cover.
13. Remove sliding clutch.
14. Remove input shaft bearing cone. Temporarily place
lockout sliding clutch over rear of input shaft, teeth
toward bearing cone. Place shaft in press and re-
move.
1 - Sliding clutch
1