Service Manual D__R440, 460, 480, D_R461, 462, 463, 521, 581, 601, 651, 652, 653 Owner manual
Table Of Contents
- Warnings and Caution
- Table of Contents - Visual
- Introduction
- Failure Analysis
- Inspection
- Differential Carrier Assembly - Parts
- Forward Axle Differential Carrier Removal and Installation
- Installation of Forward Differential Carrier
- Installation of Forward Axle Housing Cover and Output Shaft Bearing Parts
- Rear Axle Differential Carrier Removal and Installation
- Rear Differential Carrier “Installation”
- Differential Lockout
- Differential Lockout Overhaul
- Original Design Lockout Overhaul
- Cylindrical Design Lockout - Overhaul
- Power Divider - Parts Exploded View
- Remove Power Divider
- Remove Power Divider from Differential Carrier (with carrier removed from axle housing)
- Disassemble, Assemble and Overhaul the Power Divider
- Disassemble Power Divider Cover (For Axles with Input Shaft Tapered Roller Bearing)
- Assemble Power Divider Cover (For Axles with Input Shaft Tapered Roller Bearing)
- Inter-axle Differential
- Output Shaft Assembly
- Install Power Divider on Differential Carrier (with carrier assembled to axle housing)
- Install Power Divider on Differential Carrier (with carrier removed from axle housing)
- Measure and Adjust Input Shaft End-Play
- Forward Axle Carrier Assembly (Single Speed) with Diff. Lock - Parts Exploded View
- Rear Axle (Single Speed) - Parts Exploded View
- Forward Axle (Two Speed) - Parts Exploded View
- Rear Axle (Two Speed) - Parts Exploded View
- Disassemble Differential Carrier (with power divider removed)
- Drive Pinion - Parts Exploded View
- Disassemble and Overhaul Drive Pinion
- Install Drive Pinion Assembly
- Install Helical Gear and Pinion Outer Support Bearing - Forward Axle Only
- Wheel Differential Assembly - Parts Exploded View
- Disassemble, Overhaul and Assemble Wheel Differential (Forward and Rear Axles)
- Planetary and 2-Speed Models (Forward and Rear Axles)
- Disassemble Dual Reduction Differential Case
- Assemble Dual Reduction Differential Case
- Install Differential-Forward and Rear Axles
- Measure and Adjust Carrier Assembly
- Wheel Differential Lock - Parts Exploded View
- Install and Adjust Wheel Differential Lock, Dual Range Shifters
- Piston Air Shift Unit
- Air Shift Unit Replacement
- Air Shift Unit Overhaul
- Housing and Rear Cover Assembly - Parts Exploded View
- Seals
- Housing Breather
- Wheel End Seal - Parts Exploded View
- Remove and Overhaul Wheel End Seal
- Wheel Adjustment Systems
- Verify Wheel End-play Procedure
- Lubricate Wheel End
- Lubrication
- Lube Change Intervals
- Change Lube
- Standpipes
- Torque Chart
- Wheel Differential Lock
- Differential Lock Theory of Operation
- Control Systems
- Dual Range Axle Shift Systems
- Troubleshooting
- Proper Vehicle Towing
- Axle Shift System Components
- Inter-Axle Differential Lockout With Interlock Control Valve (straight-air type)
- Theory of Operation
- Power Flow and Torque Distribution
- Lubrication
- Torque Distribution in Low Range
37
Power Divider
Power Divider
Disassemble Output Shaft
Snap ring is spring steel and may pop off. Wear safety glass-
es when removing.
1. Mount shaft assembly in vise, using brass vise jaw
protectors. Remove snap ring, side gear and bearing
cone assembly.
2. Remove output shaft o-rings. If replacement is nec-
essary, remove bushing mounted in end of output
shaft.
Note: Output Shaft Bushings: In September 1994, a bushing-
less output shaft design change was implemented on
production 461, 521 and 581 model axles. Replace bush-
ings only if originally equipped.
3. Remove bearing cone from side gear using press and
split-type puller.
Assemble Output Shaft
Note: Lubricate parts with gear lube during assembly.
1. Press bearing cone on output shaft side gear.
Provide protection against possible gear teeth damage dur-
ing press operation.
2. Mount output shaft in a vise. Lubricate and install o-
rings. If removed, install bushing in end of output
shaft.
Note: Tandem Axles built after September 1994 are equipped
with bushingless output shafts. Verify output shaft de-
sign before attempting to install a bushing.
Snap ring is spring steel and may pop off. Wear safety glass-
es when installing.
3. Install side gear and bearing cone assembly. Install
snap ring, be careful not to over stretch the snap ring
when installing it into the shaft.
WARNING
CAUTION
WARNING