Service Manual D__R440, 460, 480, D_R461, 462, 463, 521, 581, 601, 651, 652, 653 Owner manual
Table Of Contents
- Warnings and Caution
- Table of Contents - Visual
- Introduction
- Failure Analysis
- Inspection
- Differential Carrier Assembly - Parts
- Forward Axle Differential Carrier Removal and Installation
- Installation of Forward Differential Carrier
- Installation of Forward Axle Housing Cover and Output Shaft Bearing Parts
- Rear Axle Differential Carrier Removal and Installation
- Rear Differential Carrier “Installation”
- Differential Lockout
- Differential Lockout Overhaul
- Original Design Lockout Overhaul
- Cylindrical Design Lockout - Overhaul
- Power Divider - Parts Exploded View
- Remove Power Divider
- Remove Power Divider from Differential Carrier (with carrier removed from axle housing)
- Disassemble, Assemble and Overhaul the Power Divider
- Disassemble Power Divider Cover (For Axles with Input Shaft Tapered Roller Bearing)
- Assemble Power Divider Cover (For Axles with Input Shaft Tapered Roller Bearing)
- Inter-axle Differential
- Output Shaft Assembly
- Install Power Divider on Differential Carrier (with carrier assembled to axle housing)
- Install Power Divider on Differential Carrier (with carrier removed from axle housing)
- Measure and Adjust Input Shaft End-Play
- Forward Axle Carrier Assembly (Single Speed) with Diff. Lock - Parts Exploded View
- Rear Axle (Single Speed) - Parts Exploded View
- Forward Axle (Two Speed) - Parts Exploded View
- Rear Axle (Two Speed) - Parts Exploded View
- Disassemble Differential Carrier (with power divider removed)
- Drive Pinion - Parts Exploded View
- Disassemble and Overhaul Drive Pinion
- Install Drive Pinion Assembly
- Install Helical Gear and Pinion Outer Support Bearing - Forward Axle Only
- Wheel Differential Assembly - Parts Exploded View
- Disassemble, Overhaul and Assemble Wheel Differential (Forward and Rear Axles)
- Planetary and 2-Speed Models (Forward and Rear Axles)
- Disassemble Dual Reduction Differential Case
- Assemble Dual Reduction Differential Case
- Install Differential-Forward and Rear Axles
- Measure and Adjust Carrier Assembly
- Wheel Differential Lock - Parts Exploded View
- Install and Adjust Wheel Differential Lock, Dual Range Shifters
- Piston Air Shift Unit
- Air Shift Unit Replacement
- Air Shift Unit Overhaul
- Housing and Rear Cover Assembly - Parts Exploded View
- Seals
- Housing Breather
- Wheel End Seal - Parts Exploded View
- Remove and Overhaul Wheel End Seal
- Wheel Adjustment Systems
- Verify Wheel End-play Procedure
- Lubricate Wheel End
- Lubrication
- Lube Change Intervals
- Change Lube
- Standpipes
- Torque Chart
- Wheel Differential Lock
- Differential Lock Theory of Operation
- Control Systems
- Dual Range Axle Shift Systems
- Troubleshooting
- Proper Vehicle Towing
- Axle Shift System Components
- Inter-Axle Differential Lockout With Interlock Control Valve (straight-air type)
- Theory of Operation
- Power Flow and Torque Distribution
- Lubrication
- Torque Distribution in Low Range
40
Power Divider
Install Power Divider on Differential Carrier
(with carrier removed from axle housing)
The following instructions pertain to installation of power di-
vider on differential carrier with carrier removed from axle
housing.
1. If output shaft side gear bearing cup was removed,
press bearing cup in carrier. Use a press and appro-
priate sleeve or use a brass drift and a mallet. Tap
bearing cup into its bore making certain cup is evenly
and firmly seated.
2. Lubricate o-rings, then install output shaft assembly
in carrier.
3. Insert axial spring and thrust button in the end of the
output shaft.
Note: Early model axles may not be equipped with axial spring
and thrust button. If your axle was not equipped with
these parts, go to step 4.
4. Install inter-axle differential assembly on output shaft
side gear (with nuts facing away from output shaft
side gear).
5. Apply silicone gasket compound on carrier mating
surface.
Note: Gasket compound will set in 20 minutes. Install power
divider before compound sets or reapply.
6. Attach chain hoist to input yoke and install power di-
vider assembly. During installation, rotate input shaft
to engage input shaft splines with inter-axle differen-
tial. After installation, rotate input shaft again. Output
shaft should turn when input shaft is rotated if as-
sembly is correct.
1 - Input Shaft
2 - Thrust button (Part #51228)
3 - Axial spring (Part #51238)
4 - Output shaft
2
3
1
4