User's Manual

Instruction
US
Cautions
Note
FCC Part 15 Compliance ISED Regulatory Compliance
User Manual
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device
must accept any interference received, including
interference that may cause undesired operation.
•CAUTION: Changes or modifications not expressly
approved by the party responsible for compliance
could void the user’s authority to operate the product.
•Note: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to
radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged
to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment
and receiver.
- Connect the equipment into an outlet on a circuit
dierent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. This
equipment should be installed and operated with
minimum distance 20cm between the radiator and
your body. This transmitter must not be co-located
or operating in conjunction with any other antenna
or transmitter.
This device contains licence-exempt transmitter(s)/receiv-
er(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including
interference that may cause undesired operation
of the device.
L’émetteur exempt de licence contenu dans le présent
appareil est conforme aux CNR d’Innovation, Sciences
et Développement économique Canada applicables
aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes :
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
This equipment complies with IC RSS-102 radiation
exposure limits set forth for an uncontrolled environment.
This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter.
This equipment should be installed and operated with
minimum distance 20cm between the radiator and
your body.
Cet équipement est conforme aux limites d'exposition
aux radiations IC CNR-102 établies pour un environnement
non contrôlé. Cet émetteur ne doit pas être situé ou
fonctionner conjointement avec une autre antenne ou
un autre émetteur. Cet équipement doit être installé et
utilisé avec une distance minimale de 20 cm entre le
radiateur et votre corps.
IC warning
Specification
This device contains licence-exempt transmitter(s)/re-
ceiver(s) that comply with Innovation,
Science and Economic Development Canada’s
licence-exempt RSS(s). Operation is subject to the
following two conditions:
1. This device may not cause interference; and
2. This device must accept any interference, including
interference that may cause undesired operation
of the device.
Cet appareil contient des émetteurs / récepteurs
exemptés de licence conformes aux RSS (RSS)
d'Innovation, Sciences et Développement
économique Canada. L'exploitation est autorisée aux
deux conditions suivantes :
1. l'appareil ne doit pas produire de brouillage, et
2. l'utilisateur de l'appareil doit accepter tout brouillage
radio électrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement."
1. Do not exert excess force on the product.
2. Do not disassemble the product or let it come into
direct contact with heat or water.
3. Be careful when using the product in a hot or humid
environment as it may damage the circuit.
4. Do not place magnetized chip cards (e.g. ID cards, credit
cards) near the product as magnets may demagnetize
the cards and cause them to malfunction.
5. Do not place a foreign object between the charger and
then iPhone as the magnetic force may weaken.
6. Medical devices (e.g. pulse measuring device, hearing
aid) may indirectly interfere with the product; keep them
at least 20cm away from the product.
7. Keep away from children.
* The product image herein is provided as an example
and user's guide for the portable high-speed wireless
charger and may dier from the actual product.
* For smartphones that do not support wireless charging,
you need to use a separate wireless charging patch or
wireless charging case.
• Model : PF2009
• Input : DC 5.0V 1.5A, 9.0V 1.67A
• Output : 5.0W / 7.5W
• Dimensions (Not include Cable) : 62 x 62 x 6mm /
2.44 x 2.44 x 0.24in
• Weight (Include Built-in Cable) : 47g / 1.66oz
B Class Equipment (Equipment for home use)
* This product is mainly for home use with radio wave
acceptability registration; therefore, it can be used in all
areas.
Spigen PowerArc
ArcField™ Magnetic
Wireless Charger
for iPhone 12 Series
PF2009
Caution
20W USB-C PD Power Adapter is Recommended
for high-speed wireless charging.
USB Power Adapter is not included.
20W USB-C PD
Power Adapter
1
2
iPhone 12 series
O X
Do not pull on the
built-in cable when
detaching the wireless
charger. Pulling hard
on the cable will cause
short circuits.
X
K
Cutting Line (자르는�선)
Folding Line (접는�선)
PF2009_메뉴얼�수정
칼선/접선
(Cutting/Folding line)
작업자�의견
(Designer
comment)
*단순업무�외�기재�필요
지류
(Material)
ART 120
HAN
47x93mm
Ver.
SKU
0 -
작업일
(Date)
자재�사이즈
(Size)
20. 11. 3
작업자
(Designer)
후가공
(Process)