User's Manual

TROUBLESHOOTING GUIDE
PROBLEM
Jet will not start or
has low power.
Jet will not turn.
Jet is flying too low.
Jet is flying too high.
Motors don’t stop when
Controller is turned OFF.
CAUSE
1. Jet not charged.
2. Battery power is drained.
3. Jet was not set to OFF during
charging.
4. Charger/Controller was not set
to “OFF”.
1. Control is not ON.
2. Controller antenna is not extended.
3. It’s a windy day and the winds are
too strong for the plane.
1. Needs more power.
2. The six AA batteries in the
Charger/Controller are drained.
1. Need to decrease power.
1. Set to full throttle.
SOLUTION
1. Charge jet for a complete charge cycle.
2. Replace the Charger/Controller batteries after 20 flights.
3. The jet won’t accept a charge in the ON position. Always set to
“OFF” before charging.
4. The Charger/Controller will NOT charge in the “Control ON” or
“Controller OFF” position. Always set the Charger/Controller to
“CHARGE” before attempting to charge.
1. Set Controller to “Controller ON”
2. Fully extend Controller antenna before flying.
3. Do not fly in winds. Windy conditions will limit and prevent
your ability to control the jet.
1. Push the Throttle UP.
2. Install new batteries.
1. Pull the Toggle DOWN.
1. Turn Controller ON, reduce throttle to 0 and turn
Controller OFF.
IMPORTANT BATTERY INFORMATION
Battery installation should be performed by an adult. Use only batteries
recommended in the instruction sheet. Be careful to install the batteries
with the correct polarity, as indicated.
• Do not mix old and new batteries.
• Do not mix alkaline, standard or rechargeable batteries.
• Battery installation should be done by an adult.
• Non-rechargeable batteries are not to be recharged.
• Rechargeable batteries are to be removed from the toy before being
charged (if removable).
• Rechargeable batteries are only to be charged under adult supervision
(if removable).
• Only batteries of the same or equivalent type as recommended are
to be used.
• Batteries are to be inserted with the correct polarity.
• Exhausted batteries are to be removed from the toy.
• The supply terminals are not to be short-circuited.
• Different types of batteries, or new and used batteries are not to
be mixed.
• Exhausted batteries are to be removed, as they will adversely affect the
performance.
REQUIRED BATTERIES: Charger/Controller takes 6 AA Alkaline Batteries (not included).
Your jet is equipped with a Lithium Polymer battery; please also pay
attention to the following cautions for safe use:
• Do not dispose of battery in fire or heat.
• Do not use or leave the battery near a heat source such as fire or heater.
• Do not strike or throw the battery against hard surfaces.
• Do not immerse the battery in water. Keep the battery in a cool dry
environment.
• When charging, only use the battery charger specifically for that purpose.
• Do not over-charge the battery.
• Do not connect the battery to an electrical outlet.
• Do not directly solder the battery or pierce the battery with a nail or other
sharp objects.
• Do not transport or store the battery together with metal objects such as
necklaces, hairpins, etc.
• Do not disassemble or alter the battery.
• The battery will need to be recharged if the product is not in use for at
least 6 months.
• Turn off your equipment power switch after use.
• As for a used battery, please recycle the battery by covering the terminals
with insulation tape or inserting into an individual polybag.
CAUTION:
PLEASE READ BEFORE CHARGING OR USING BATTERY.
TM
Contains Lithium Polymer
battery. Battery must be
recycled or disposed
of properly.
Manufactured for Spin Master Ltd.
Spin Master Ltd., 450 Front Street West, Toronto, ON M5V 1B6 Canada
Spin Master, Inc., PMB #10053, 300 International Drive, Suite 100,
Williamsville, NY 14221, USA
Spin Master Toys Far East Limited, Rm #1113, 11/F,
Chinachem Golden Plaza, 77 Mody Rd., Tsimshatsui E., Kowloon, HK
North American Consumer Information
Phone: [phone]
www.spinmaster.com
TM and © 2009 Spin Master Ltd. Air Hogs ® is
a registered trademark of Spin Master Ltd. All
rights reserved. Conforms to product safety
standards ASTM F963, regulatory requirements.
Products and colours may vary. Please retain
this information for future reference. Patent
Pending. MADE IN CHINA.
20023561 NTL English REV 0
T44292_0002_20023561_NTL_IS_R2
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation. Warning: Changes or modifications to this unit not
expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment. Note: This equipment has been tested and
found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.
FCC REQUIREMENTS
This Category II radio communication device complies with Industry Canada Standard RSS-310.
Carrier frequency: 27.145 MHz Field Strength: 64.8
dBuV/m at 3m