OWNER’S MANUAL
Table of Contents Product Registration ..2 Important Safety Instructions .. 3 Important Electrical Information .. 4 Important Operation Instructions .5 Assembly instructions for ET288. 6 Assembly instructions for ET388. 9 Operation of Your New Treadmill .. .12 General Maintenance. 15 Service Checklist - Diagnosis Guide .
CONGRATULATIONS ON YOUR NEW TREADMILL AND WELCOME TO THE SPIRIT FAMILY! Thank you for your purchase of this quality treadmill from Spirit Manufacturing, Inc. Your new treadmill was manufactured by one of the leading fitness manufacturers in the world and is backed by one of the most comprehensive warranties available. Through your dealer, Spirit will do all we can to make your ownership experience as pleasant as possible for many years to come.
Important Safety Instructions WARNING - Read all instructions before using this appliance. DANGER - To reduce the risk of electric shock disconnect your Spirit treadmill from the electrical outlet prior to cleaning and/or service work. WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons, install the treadmill on a flat level surface with access to a 120-volt, 15-amp grounded outlet. DO NOT USE AN EXTENSION CORD UNLESS IT IS 14AWG OR BETTER, WITH ONLY ONE OUTLET ON THE END.
Important Electrical Information WARNING! l l l l NEVER use a ground fault circuit interrupt (GFCI) wall outlet with this treadmill. Large switching currents of the drive motor will trip GFCI type outlets, as any appliance with a large motor will. Route the power cord away from any moving part of the treadmill including the elevation mechanism and transport wheels. NEVER remove any cover without first disconnecting AC power.
Important Operation Instructions l l l l l l NEVER operate this treadmill without reading and completely understanding the results of any operational change you request from the computer. Understand that changes in speed and incline do not occur immediately. Set your desired speed on the computer console and release the adjustment key. The computer will obey the command gradually. NEVER use your treadmill during an electrical storm.
Assembly Instructions for ET288 ASSEMBLY PACK CHECK LIST #106 - 5/16 x 23mm Curved Washer (x4) #105 - 5/16 x 18mm Flat Washer (x4) #104 - 5/16 x 1/2 Button Head Socket Bolt (x12) #44 - Safety Key (x1) #109 - Lubricant (x1) #108 - M6 Allen Wrench (x1) #107 - Combination M5 Allen Wrench & Phillips Head Screwdriver (x1) 6 ET288/ET388
n STEP 1 Remove all the parts from the carton and lay the main base frame on a flat level surface. n STEP 2 Connect the cable from the base frame (53) to the cable in the right side upright tube (54) and slide the tube into the base frame tube. Be careful not to pinch the wire harness. Slide the left upright tube into the base frame tube.
n STEP 4 This step is easier if you have someone else helping to hold the console while you connect the wires. Connect the handlebar incline switch wire (121) on the left side to the mating connector (122) of the console. Connect the handlebar speed switch wire (119) on the right side to the mating connector (120) of the console and then connect the computer cable (54) to the mating connector (55) of the console.
Assembly Instructions for ET388 ASSEMBLY PACK CHECK LIST #128 - Speed Nut Clip (6pcs) #120 #130 - 5/16 x 1/2 Button Head Socket Bolt (12pcs) #75 - Safety Key (1pc) 5mm x 16 mm Self-Tappingscrew (6pcs) #30 - Lubricant (1) #132 - M6 Allen Wrench (1pc) #131 - Combination M5 Allen Wrench & Phillips Head Screwdriver (1 pc) 9 ET288/ET388
n STEP 1 Remove all the parts from the carton and lay the main base frame on a flat level surface. n STEP 2 Connect the cable from the base frame (49) to the cable in the right side upright tube (50) and slide the tube into the base frame tube. Be careful not to pinch the wire harness. Slide the left upright tube into the base frame tube. 50 49 n STEP 3 Install, and just hand tighten for now, all eight 5/16 x 1/2 socket head bolts (130). Now tighten all eight bolts as tight as possible.
n STEP 4 This step is easier if you have someone else helping to hold the console while you connect the wires. Connect the handlebar incline switch wire (55) on the left side to the mating connector (38) of the console. Connect the handlebar speed switch wire (54) on the right side to the mating connector (37) of the console and then connect the computer cable (50) to the mating connector (48) of the console. l STEP 5 Secure the console with four 5/16 x 1/2 socket head bolts (130).
Operation of the ET288 & ET388 Treadmill 12 ET288/ET388
GETTING STARTED: Power the treadmill on by plugging it into a grounded wall outlet, then turn on the power switch located at the front of the treadmill below the motor hood. Ensure that the safety key is installed, as the treadmill will not operate without it. When the power is initially turned on, the display will light up and then show an Odometer reading in the Distance window. The odometer reading shows how many virtual miles the treadmill gone.
PROGRAMS: MANUAL: • When the treadmill is powered on the main display will show PO • You can press start or if you want to set the clock to count down press the Enter key. The Time window will be blinking, use the Fast/Slow buttons to adjust the Time. • Press the Start key to begin the program. • Press the Enter key to switch the main data being displayed in the big window. PROGRAMS 1~5: • When the treadmill is powered on, press the Fast/Slow keys to select P1 to P5.
General Maintenance Belt and Bed - Your treadmill uses a very high-efficient low-friction bed. Performance is maximized when the bed is kept as clean as possible. Use a soft, damp cloth or paper towel to wipe the edge of the belt and the area between the belt edge and frame. Also reach as far as practical directly under the belt edge. This should be done once a month to extend belt and bed life. Use water only - no cleaners or abrasives.
TREADBELT TRACKING ADJUSTMENT: The performance of your treadmill is dependent on the frame running on a reasonably level surface. If the frame is not level, the front and back roller cannot run parallel, and constant belt adjustment may be necessary. The treadmill is designed to keep the tread-belt reasonably centered while in use. It is normal for some belts to drift near one side while the belt is running with no one on it.
BELT / DECK LUBRICATION: Do not lubricate with other than Spirit approved lubricant. Your treadmill comes with one tube of lubricant and extra tubes can be ordered directly from Spirit. There are commercially available lube kits, but the only one currently approved by Spirit is Lube-N-Walk. These kits come with an application wand that makes applying the lubrication easier. The kits can be purchased from Spirit or directly from Lube-N-Walk here: http://www.jadfitness.
Service Checklist - Diagnosis Guide Before contacting your dealer for aid, please review the following information. It may save you both time and expense. This list includes common problems that may not be covered under the treadmill s warranty.
Manufacturer s Limited Warranty Effective July 15, 2009 TREADMILL LIMITED WARRANTY Spirit Fitness Inc. warrants all its home use treadmill parts for a period of time listed below, from the date of retail sale, as determined by a sales receipt or in the absence of a sales receipt, eighteen (18) months from the original factory shipping date.