User Manual
Table Of Contents
- Manual Neos
- Symbols and Notes
- Scope of Delivery and Packaging
- Introduction
- Important Security Advices
- Hook Up
- Rear Panel – Switches & Connections, Basics
- Rear Panel – Power Wiring Diagram
- Rear Panel – Signal Wiring Diagram
- Rear Panel
- Operation
- Control Elements Input Path
- Control Elements Master Path
- DAW-Integration
- Specifications
- Copy Master Recall Settings
- Block Diagram
- Mounting Dimensions
- Mounting Angles
12
Neos
Rear Panel – Power Wiring Diagram
R LREC OUT
L RREC OUT
GND LIFT
GND
R LTAPE Rt.
L RTAPE Rt.
R LMONITOR A
L RMONITOR A
R LMONITOR B
L RMONITOR B
R LALT. OUT
L RALT. OUT
TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK.
DO NOT EXPOSE THIS UNIT RAIN OR MOISTURE.
DISCONNECT MAINS BEFORE REMOVING COVER.
THIS EQUIPMENT MUST BE EARTHED.
WARNING
Neos – Model 1010
www.spl.info
Made in Germany
Serial Number
XLR (BAL.): 1 = GND | 2 = HOT (+) | 3 = COLD (–)
ALT. OUT XLR (UNBAL.):
1 = GND | 2 = HOT (+) | 3 = GND
XLR CONNECTOR WIRING
AVIS: RISQUE DE CHOC ÉLECTRIQUE – NE PAS OUVRIR
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
CONNECT TO EXTERNAL PSU
CONNECT TO EXTERNAL PSU
GND LIFT
GND LIFT
GND LIFT
1 = GND
RECORDING BUS: 2 = HOT (+) | 3 = COLD (–)
MONITOR BUS: 4 = HOT (+) | 5 = COLD (–)
SLAVE CONNECTOR WIRING
DB25 COMPLY WITH TASCAM STANDARD.
PLEASE REFER TO MANUAL FOR DETAILS.
DB 25 CONNECTOR WIRING
INPUTS 1 – 8
INPUTS 9 – 16
INPUTS 17 – 24
LR INS. RETURNLR INS. SENDLR METERINGLR SLAVE
SERIAL NUMBER
230V~50Hz | 2A slow
115V~60Hz | 4A slow
VOLTAGE | FUSE GND LIFT
WARNING:
TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK DO
NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. DISCONNECT MAINS
BEFORE REMOVING COVER. THIS EQUIPMENT MUST BE EARTHED.
AVIS: RISQUE DE CHOC ÉLECTRIQUE - NE PAS OUVRIR
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
POWER
MAINS INPUT
POWER OUTPUT TO AUDIO UNIT
Before you use the Neos, make sure that this voltage selector switch setting reflects
the correct local power line voltage (115V position: 110-120V, 230 V position: 220-240V).
In the drawing above the 230 V position is selected.
BEFORE switching on the external power supply,
connect the external power supply and the Neos
with the multi-pin power cord fixed to the external power supply.
NEVER disconnect the external power supply
from the Neos while the power supply
is still switched on.
First switch off the external power supply
and wait at least one minute before disconnecting.
Otherwise residual currents can cause serious damages!
1
2
3
The rear panel GND lift switches
eliminate hum by separating
the internal ground from the
unit’s housing ground.
If hum occurs, press the
switches to activate GND lift.
spl.info
NEOS
Power Supply Unit
Model 1010-P
MADE IN GERMANY
IMPORTANT:
CONNECT POWER CORD
TO NEOS BEFORE SWITCHING ON POWER!
Use slow blow fuse.