Phonitor One d Headphone Monitoring Amplifier 32 Bit/768 kHz DA converter EN DE NUMBER One IN SOUND
1 Read the security advices on page 6! 2 Read the installation instructions of the included external power supply on page 8. 9 Connect the line out to the inputs of your analog audio device to benefit from the 32-bit Velvet Sound™ DA converter. The Line Out has always unity gain – it is not controlled by the volume knob. 3 Make sure that the power switch on the rear is set to Off (Off = out position / ON = in position). 10 Switch the Phonitor One d on by pressing the power button.
5 12 3 10 4 11 9 12 7 6 8 EN DE Phonitor One d 3
Specifications 4 Analog inputs & outputs; 6.35 mm (1/4") TRS Jack (balanced), RCA USB, 32-Bit AD/DA Input gain (max.) +22.5 dBu USB (B), PCM sample rates 44.1/48/88.2/96/176.4/192/ 352.8/384/705.6/768 kHz Input impedance Line In 2 (balanced) 20 kΩ Common mode rejection < 60 dB USB (B), DSD over PCM (DoP), sample rates 2.8 (DSD64), 5.6 (DSD128), 11.2 (DSD256) MHz Input impedance Line In 1 (unbalanced) 47 kΩ 0 dBFS calibrated to 15 dBu Output gain (max.
Headphones Output; 6.35 mm (1/4") TRS Jack Internal Power Supply Wiring Tip = Left, Ring = Right, Sleeve = GND Source impedance 20 Ω Frequency range (-3 dB) 10 Hz - 200 kHz Noise (A-weighted, 600 Ω) -97 dBu THD + N (0 dBu, 10 Hz – 22 kHz, 600 Ω) 0,002 % THD + N (0 dBu, 10 Hz – 22 kHz, 32 Ω) 0,013 % External Power Supply Max output power (600 Ω) 2 x 190 mW AC/DC switching adapter Mean Well GE18/12-SC Max output power (250 Ω) 2 x 330 mW DC plug (+) pin 2.1mm; (-) outside ring 5.
Security Advices Before starting up the device: • Read thoroughly and follow the security advices. • Read thoroughly and follow the manual. • Observe all warning instructions on the device. • Please keep the manual as well as the security advices in a safe place for future reference. Warning Always follow the security advices listed below to avoid serious injuries or even deadly accidents due to electric shocks, short circuit, fire or other dangers.
Do not place the device in a location where it may come into contact with corrosive gases or salty air. This may result in malfunction. Before moving the device, remove all connected cables. When setting up the device, make sure that the mains socket outlet you are using is easily accessible. If some trouble or malfunction occurs, immediately turn off the power switch and disconnect the power supply from the mains socket outlet.
Installation Instructions External Switching Power Supply Installation • Before attaching the DC plug of an adapter to equipment, please unplug the adapter from the AC power and verify the unit is within the voltage and current rating on the equipment. • Keep the linkage between the adapter and its power cord tightly as well as connecting the DC plug to equipment properly. • Protect the power cord from being trodden on or being squashed.
Phonitor One d Headphone Monitoring Amplifier 32 Bit/768 kHz DA converter EN DE NUMBER Phonitor One d One IN SOUND 9
1 Lesen Sie die Sicherheitshinweise auf Seite 14! 8 Schließen Sie Ihren Computer oder Ihr Tablet/ Smartphone am USB-Eingang an. 2 Lesen Sie die Installationsanleitung des mitgelieferten Steckernetzteils auf Seite 16! 9 Schließen Sie an den Line-Ausgang Ihr analoges Gerät an, um in den Genuss des 32-Bit Velvet Sound™ DA-Konverters zu kommen. 3 4 Achten Sie darauf, dass sich der Netzschalter auf der Rückseite in der Aus-Stellung befindet (Schalter nicht gedrückt).
5 12 3 10 4 11 9 12 7 6 8 EN DE Phonitor One d 11
Technische Daten Analoge Ein- und Ausgänge; 6,35mm Stereoklinkenbuchsen (symmetrisch), Cinch USB, 32-Bit AD/DA USB (B), PCM-Abtastraten: 44,1/48/88,2/96/176,4/192/ 352,8/384/705,6/768 kHz Eingangspegel (max.) +22.
Kopfhörerausgang Interne Stromversorgung; Schaltnetzteil mit Sekundärtraformator 6,35mm Stereoklinkenbuchse Spitze = links, Ring = rechts, Schaft = GND Quellwiderstand 20 Ω Frequenzgang (- 3 dB) 10 Hz - 200 kHz Rauschen (A-bewertet, 600 Ω) -97 dBu THD + N (0 dBu, 10 Hz – 22 kHz, 600 Ω) 0,002 % THD + N (0 dBu, 10 Hz – 22 kHz, 32 Ω) 0,013 % Max. Ausgangsleistung (600 Ω) 2 x 190 mW Max. Ausgangsleistung (250 Ω) 2 x 330 mW Max.
Sicherheitshinweise Vor der Inbetriebnahme des Gerätes: • • • • Lesen und befolgen Sie diese Sicherheitshinweise. Lesen und befolgen Sie diese Anleitung. Beachten Sie alle Warnhinweise auf dem Gerät. Bewahren Sie die Bedienungsanleitung mit den Sicherheitshinweisen auf, damit Sie später darin nachschlagen können.
Platzieren Sie das Gerät nicht an einem Ort, an dem es in Kontakt mit korrosiven Gasen oder salzhaltiger Luft gelangen könnte. Dadurch kann es zu Fehlfunktionen kommen. Entfernen Sie alle angeschlossenen Kabel, bevor Sie das Gerät bewegen. Vergewissern Sie sich beim Aufstellen des Geräts, dass die von Ihnen verwendete Netzsteckdose leicht erreichbar ist. Sollten Probleme auftreten oder es zu einer Fehlfunktion kommen, schalten Sie das Gerät sofort aus, und ziehen Sie das Netzteil aus der Steckdose.
Installationsanleitung externes Steckernetzteil Bestimmungsgemäßer Gebrauch MEAN WELL Spannungswandler sind für die Versorgung von elektrischen Verbrauchern bestimmt und erfüllen die Anforderungen der RoHS (2011/ 65/EG), Niederspannungsrichtlinie (2014/35/EU) und der EMV-Richtlinie (2014/30/EU).